• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.610-612
• /
• 2013

A novel balanced distributed amplifier (DA) was proposed using novel impedance transforming MEMS baluns. The impedance transforming MEMS balun is matched to $50{\Omega}$ at one input port and $25{\Omega}$ at two output ports. It is based on the electric field mode-change method, thus it is strongly independent of frequency and very compact. The novel balanced DA consists of two $25{\Omega}$-matched DAs and these are combined by $50{\Omega}$-to-$25{\Omega}$ baluns. Theoretically, it has two times wider bandwidth and power capability than the conventional DA. So as to verify the proposed concept, we designed and fabricated a conventional DA and the proposed one using 0.15-${\mu}m$ GaAs pHEMT technology.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.626-632
• /
• 1995

In this paper, The effect of the impedances in SNOSFET's memory devices has been developed. The effect of source and drain impedances measured by means of two bias resistances - field effect bias resistance by inner region, external bias resistance. The effect of the impedances by source and drain resistance shows the dependence of the function of voltages applied to the gate. It shows the differences of change in source drain voltage by means of low conductance state and high conductance state. It shows the delay of threshold voltages. The delay time of low conductance state and high conductance state by the impedances effect shows 3[.mu.sec] and 1[.mu.sec] respectively.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.5
• /
• pp.719-725
• /
• 2014

Transient of Electric railway vehicle occurs when change to another state. The duration of the transient phenomenon only takes a few second. During this time is considered, the present of short circuit current and the normal state, the energy is present in the form of a magnetic field. Recognized by the vibration of the transient voltage or transient current at witch energy is present in the field. This paper is presented the result of transient characteristics by transformer % impedance at the time of opening and closing of the main circuit Breaker on the electric railway vehicle.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.3
• /
• pp.171-180
• /
• 2020

This paper presents the implementation and control methods of a battery simulator. The proposed battery simulator can emulate the dynamic characteristics of any actual battery using the second RC ladder model of the equivalent circuit. Moreover, it can emulate the variation of impedance, which is the result of the change of battery characteristics due to the aging effect. The parameters of the battery simulator can be derived from the sequence of tests of the actual battery or only from the data supplied by the battery manufacturer. Proposed methods for the battery simulator are tested by extensive experiments. Test results show that the proposed battery simulator can emulate not only the dynamic characteristics but also the aging effects of the actual battery in real time.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.160-166
• /
• 1998

In this research a 2-dimensional motion generator composed of two linear motors was developed. The inertia, damping and/or stiffness characteristics of the motion generator can be changed on the real-time basis by properly regulating the force generated by the linear motors. That is, active impedance is implemented without actual change in the physical structure of the motion generator. Control of the motor force is carried out by controlling the input currents supplied to the linear motors based on the combination of the PI controller and feedforward controller. This motion generator can be used to measure a kinesthetic sense associated with the human arm and thus to develop the products for which the kinesthetic sense is taken into account.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.4
• /
• pp.239-244
• /
• 2015

Each biological tissue has endemic electrical characteristics owing to various differences such as those in cellular arrangement or organization form. The endemic electrical characteristics change when any biological change occurs. This work is a preliminary study surveying the changes in the electrical characteristics of biological tissue caused by radiation exposure. For protection aganinst radiation hazards, therefore the electrical characteristics of living tissue were evaluated after development of the automatic control measurement system using LabVIEW. No alteration of biological tissues was observed before and after measurement of the electrical characteristics, and the biblogical tissues exhibited similar patterns. Through repeated measurements using the impedance/gain-phase analyzer, the coefficient of variation was determined as within 10%. The reproducibility impedance phase difference in electrical characteristics of the biological tissue did not change, and the tissue had resistance. The absolute value of impedance decreased constantly in proportion to the frequency. It has become possible to understand the electrical characteristics of biological tissues through the measurements made possible by the use of the developed. automatic control system.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.689-696
• /
• 2021

In this paper, in order to apply Prognostics and Health Management(PHM) to an electronic system or circuit, a circuit capable of detecting and predicting defect characteristics inside the system or circuit is implemented, and the results are described. In the previous study, we demonstrated that the frequency of the amplitude of S-parameter changed as the circuit defect progressed. These characteristics were measured by network analyser. but in this study, even if the same defect detection method is used, a circuit is proposed to check the progress of the defect, the remaining time, and the occurrence of the defect without large measurement devices. The circuit is designed to detect the change in impedance that generates changes of S-parameter, and it is verified through simulation using the measurement results of Bond-wires.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.320-321
• /
• 2006

In this work, impedance Spectroscopic analysis was applied to study the effect of plasma treatment on the surface of indium-tin oxide (ITO) anodes using $CF_4g$ as and to model the equivalent circuit for organic light emitting diodes (OLEDs) with the $CF_4$ plasma treatment of ITO surface at the anodes. This device with ITO/TPD/$Alq_3$/LiF/Al structure can be modeled as a simple combination of a resistor and a capacitor. The $CF_4$ plasma treatment on the surface of ITO shifts the vacuum level of the ITO as a result of which the barrier height for hole injection at the ITO/organic interface is reduced. The Impedance spectroscopy measurement of the devices with the $CF_4$ plasma treatment on the surface of ITO anodes shows change of values in parallel resistance ($R_p$) and parallel capacitance ($C_p$).

• BMB Reports
• /
• v.41 no.2
• /
• pp.126-131
• /
• 2008

The folding of aptamer immobilized on an Au electrode was successfully detected using label-free electrochemical methods. A thrombin binding DNA aptamer was used as a model system in the presence of various monovalent cations. Impedance spectra showed that the extent to which monovalent cations assist in folding of aptamer is ordered as $K^+$ > $NH_4^+$ > $Na^+$ > $Cs^+$. Our XPS analysis also showed that $K^+$ and $NH_4^+$ caused a conformational change of the aptamer in which it forms a stable complex with these monovalent ions. Impedance results for the interaction between aptamer and thrombin indicated that thrombin interacts more with folded aptamer than with unfolded aptamer. The EQCM technique provided a quantitative analysis of these results. In particular, the present impedance results showed that thrombin participates a folding of aptamer to some extent, and XPS analysis confirmed that thrombin stabilizes and induces the folding of aptamer.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.3
• /
• pp.771-783
• /
• 1996

A desing technique of 8 ports variable wave impedance generator (8P-VWIG) is described. The design technique employs not only a numerical algorithm to find the structure with arbitrary characteristic impedance, but also a numerical solution to analyze the uniform elementrognentic fields established inside the generator. The 8P-VWIG so obtained is shown to have good performance with the VSWR of less than 1.4 at any frequency of interest below which higher order mode begin to propagate. The measured first resonant frequency is 152.1 MHz. The 8P-VWIG is designed based on the concept of an expanded multi-transmission line(8 channel). It is especially useful for the electronmagnetic interference(EMI) and electronmagnetic susceptibility(EMS) testing since it maximizes usable test crosssectional area, and its is easy change the polarization, vertical or horizontal, of field.