• Proceedings of the IEEK Conference
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.335-338
• /
• 1998

This paper presents calculated results for the infinite phased arrays of the probe-fed rectagualr microstrip patches. A numerical model that is based on a rigorous Green's function and galerkin solutionsis is described. In an arbitrary scan plane, the input impedance and the input reflection coefficient versus the scand angle are calculated. The effects of substrate parameters on the phased arry antenna are considered. The scan blindness phenomenon due to the surface wave is observed and the input impedance bandwidth in the arbitrary scan plane is calculated.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 한국전자파학회 2001년도 종합학술발표회 논문집 Vol.11 No.1
• /
• pp.106-110
• /
• 2001

In this paper, a broadband sleeve monopole antenna using a loading coil in sleeve is proposed. The antenna of the proposed structure has the same of the single sleeve monopole antenna, except for using the coil instead of the inner conductor in sleeve. As a result, it is found that the bandwidth is 1.239～2.154 GHz(above 53.9%) for S$\sub$11/=-10dB(VSWR<2), and the antenna impedance is good for a communication system and feeder which the impedance has 50$\Omega$.

• Proceedings of the IEEK Conference
• /
• 대한전자공학회 2000년도 ITC-CSCC -1
• /
• pp.199-202
• /
• 2000

The U-slot patch antenna has been found experimentally to provide impedance and gain bandwidths. Experiment and simulation results include impedance bandwidth, copolar and crosspolar-pattern characteristics and gain measurements. If one of the parameters such as patch width or feed position is varied, U-slot patch can also function as a dual-frequency antenna.

• Journal of the Korean Institute of Telematics and Electronics
• /
• 제5권1호
• /
• pp.13-25
• /
• 1968

A detailed analysis of the transistor wide-band feedback amplifiers using the hybrid-$\pi$ equivalent circuit has been made. It is considered both for the low freqnency and for the high frequency. The expressions of the gain, bandwidth. input impedance and output impedance have been presented. It is shown that a series feedback amplifier should be driven from the voltage source and should drive into the low resistance load, and a shunt feedback amplifier should be driven from the current source and should drive into the high resistance load. It is also shown that these stages can be coupled without use of the buffer stage or coupling transformer.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1744-1746
• /
• 1996

Surface impedance boundary condition(SIBC) concepts are introduced into the finite-difference time-domain(FDTD) method. Lossy conductors are replaced by surface impedance boundary computations reducing the soluton space and producing significant computational savings. Specifically, a surface impedance boundary condition is developed to reduce a lossy dielectric half-space. Since Maxwell's eqations are solved directly, the reflected and transmitted pulse amplitude demonstrate how the reflection and transmision coefficient determine reflected wave amplitude. In this paper, two implementations of reflection coefficient are presented. One implementation is a standard FDTD technique and the other is a FDTD using surface impedence boundary condition(FDTD-SIBC) that are applicabIe over a very large frequency bandwidth. Particulary, an efficient way to transform the time domain results to frequency domain is presented. Thus, frequency domain results are presented in one dimension and are compared with exact results.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권5호
• /
• pp.687-694
• /
• 2016

A differential power amplifier operating at millimeter-wave frequencies is demonstrated using a 65-nm CMOS technology. All of the input, output, and inter-stage network are implemented by transformers only, enabling impedance matching with low loss and a wide bandwidth. The millimeter-wave power amplifier exhibits measured small-signal gain exceeding 12.6 dB over a 3-dB bandwidth from 45 to 56 GHz. The output power and PAE are 13 dBm and 11.7%, respectively at 50 GHz.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• 제51권12호
• /
• pp.573-577
• /
• 2002

We designed wideband HTS antennas which consists of two triangle -radiation patches using a $YBa_2Cu_3O_{7-X}$ (YBCO) superconducting thin film. The major limitation of high-Tc superconducting (HTS) microstrip antennas is the narrow bandwidth due to the high Q and thin substrate. Defining bandwidth as the frequency range over which standing wave ratio (SWR) 2:1 or less, HTS antenna bandwidths are typically 0.85 % to 1.1 %. Thus considerable effort has been focused on developing antennas for broadband operation. To calculate input impedance and design of the broadband HTS antennas a moment method technique was used. The HTS antenna fabricated in this work was designed for K-band, which is useful band for satellite to satellite communications. The bandwidth obtained was a significant 6.7 % and the other measured performance of our HTS antenna, including the bandwidth, radiation Pattern, efficiency, standing wave ratio (SWR) and return losses was reported.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.523-526
• /
• 2002

We designed wideband HTS antennas which consists of two triangle-radiation patches using a YBa$_2$Cu$_3$O$\sub$7-x/ (YBCO) superconducting thin film. The major limitation of high-Tc superconducting (HTS) microstrip antennas is the narrow bandwidth due to the high Q and thin substrate. Defining bandwidth as the frequency range over which standing wave ratio (SWR) 2:1 or less, HTS antenna bandwidths are typically 0.85% to 1.1%. Thus considerable effort has been focused on developing antennas for broadband operation. To calculate input impedance and design of the broadband HTS antennas a moment method technique was used. The HTS antenna fabricated in this work was designed for K-band, which is useful band for satellite-to-satellite communications. The bandwidth obtained was a significant 6.7% and the other measured performance of our HTS antenna, including the bandwidth, radiation Pattern, efficiency, standing wave ratio (SWR) and return losses was reported.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제24권6호
• /
• pp.581-585
• /
• 2013

A technique to expand the operating impedance bandwidth of a microstrip patch antenna is presented. The antenna is fed by a truncated T-shaped microstrip line on the ground plane with the rectangular slot. The proposed microstrip patch antenna offers wide bandwidth characteristics with the rectangular slot which has optimized size and position on the ground plane. The simulation result shows a fractional bandwidth of 127.8 %(0.65 to 2.95 GHz) at VSWR 2:1.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제10권5호
• /
• pp.727-737
• /
• 1999

Printed microstrip antennas are known to have limitations in terms of bandwidth and efficiency all imposed by the presence of the dielectric substrate. In this paper, to overcome these limitations, rather than using a superstrate geometry, the printed circuit is etched out of metal and supported in "strategic points" by(metallic or nonmetallic) post. The main motivation for this work was to obtain the wide bandwidth microstrip antennal which exhibits a higher efficiency than conventional ones. In this paper, to increase the bandwidth, patch sizes, electrical thickness and impedance matching are considered.