• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.13-18
• /
• 2016

This paper presents a design of an impedance transformer (IT) with high frequency selectivity characteristics. The frequency selectivity can be controlled by even- and odd-mode impedance of a shunt coupled transmission line (TL). For experimental validation, a 50- to $20-{\Omega}$ IT was implemented at a center frequency ($f_0$) of 2.6 GHz for the long-term evolution signal. The measured results were in good agreement with the simulations, showing a return loss higher than 19 dB over a passband bandwidth of 0.63 GHz (2.28-2.91 GHz) and good sharp frequency selectivity characteristic near to the passband. The series coupled TL provides a transmission zero at 5.75 GHz, whereas the shunt coupled TL provides three transmission zeros located at 2 GHz, 3.1 GHz, and 7.14 GHz.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.2
• /
• pp.74-80
• /
• 2000

In this paper, we present a control method of mobile power assist systems. Most of mobile power assist systems have a heavy base for preventing easy tumbling, so continual movement of the base during operations causes high energy consumption and gives the high risk of human injury. Furthermore, the slow dynamics of the base limits the frequency bandwidth of the whole system. Thus we propose a cooperation control method of the mobile base and manipulator, which removes the unnecessary movements of the base. In our scheme, the mobile base does not move until the center of gravity(C.G) of the system goes outside a safety region. When C.G. reaches the boundary of the safety region, the base starts moving to recover the manipulator's initial configuration. By varying the parameters of a human impedance controller, the operator is warned by a force feedback that C.G. is on the marginal safety region. Our scheme is implemented by assigning a nonlinear mass-damper-spring impedance to the tip of the manipulator. Our scheme is implemented by a nonlinear mass-spring impedance to the tip of the manipulator. The experimental results show the efficacy of the proposed control method.

• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.85-91
• /
• 2015

We investigated the structure of inductive coupler and its magnetic coupling to increase the transmission coefficient for power line communication. A Rogowski coil, which is an air-cored inductive coupler, and a magnetic cored coupler were fabricated to analyze the transmission coefficient for different coupler parameters. This paper proposes the impedance matching method using lumped elements and an impedance transformer to increase the transmission coefficient. In the experiment, the transmission coefficient of the proposed system was increased in both narrowband and broadband cases, and a trade-off between the transmission coefficient and the bandwidth was shown. This method will be useful for the further study of impedance matching with the load variation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.282-289
• /
• 2014

In this paper, the UWB (Ultra Wide Band) band-pass filter (BPF) with compact-size using impedance mismatching in transmission line and SIR (Stepped Impedance Resonator) instead of open stubs is presented. The proposed BPF have 103 % of bandwidth and 11.2 GHz of center frequency, respectively. In additional, the operation frequencies of the suggested BPF are 4.8 GHz to 16 GHz. In this structure, the length of the transmission line is reduced to half compared with the original one by impedance mismatching technique with low frequency band (sub harmonics) and harmonic components. Also, the open stub can be used for SIR due to reduced size. Experimental results show that the insertion and return losses are 0.35 dB and 15.1 dB, respectively and the filter size is $8.92{\times}10.6mm^2$. The proposed BPF is in good agreement.

• Journal of electromagnetic engineering and science
• /
• v.13 no.2
• /
• pp.113-119
• /
• 2013

We developed a transformed, symmetrical, mushroom-like surface without via holes in cells focused on a 2.4-GHz WLAN band. Each slot in the novel type structure plays a key role in modeling at the desired frequencies. The designed artificial magnetic conductor (AMC) has several advantages, including a small size, a wider bandwidth, a short reflecting distance to the antenna, and easy fabrication because there are no via holes. Overall dimensions of the AMC cell are 21 mm $(Width){\times}21mm$ $(Height){\times}2.6mm$ (Thickness), and the bandwidth is about three times wider (11.7%) compared to that of a conventional AMC (4.0%). For evaluating the performance of the proposed structure, a reflector, which periodically consists of the designed AMC cells, was developed. The antenna with the investigated AMC reflector not only works within a quarter of the wavelength because of the extremely high wave impedance generated by the AMC cells on the surface of the structure but also reduces the specific absorption rate (SAR). Electromagnetic field (EMF) exposure to a human phantom was analyzed by applying the designed reflector to the 2.4-GHz dipole antenna in a tablet PC. The calculated peak SAR averaged over 1 g was 0.125 W/kg when the input power was 1 W and the antenna was located at 20 cm from the human phantom. However, the SAR value was only 0.002 W/kg (i.e., 98.4% blocked) when the designed reflector was inserted in front of the antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.551-558
• /
• 2012

This paper presents a dual band loop-type ground antenna using lumped-elements that control the impedance bandwidth and resonant frequency. The dual-band operation of the proposed antenna is realized by inserting an additional resonated loop feed structure into the reference ground antenna. As the proper value of the capacitor and the inductor are chosen, the impedance bandwidth of our antenna with voltage standing wave ratio(VSWR) equal to 3 is 85 MHz and 725 MHz at the 2.45 and 5.5 GHz frequency band, respectively. Its validity is demonstrated via both the computed and measured results. Good antenna patterns and efficiencies are achieved at the dual frequency bands, as well as the physically small antenna element size($10{\times}5mm^2$).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.740-747
• /
• 2019

In this paper, an antenna applicable to WLAN and WiMAX frequency bands is designed, fabricated, and measured. The proposed antenna is designed to have two branch strip line in the patch plane and a rectangular slit in the ground plane based on microstrip feeding for triple band characteristics and added a vertical strip in the ground plane to enhance impedance bandwidth characteristics. The proposed antenna is designed on a substrate with a relative permittivity of 4.4, a thickness of 1.0 mm, and has a size of $18.0mm(W1){\times}37.3mm$ (L4+L5+L7). From the fabricated and measured results, impedance bandwidths of 480 MHz (2.32 to 2.80 GHz) for 2.4/2.5 GHz band, 810 MHz (3.22 to 4.03 GHz) for 3.5 GHz band, and 1,820 MHz (5.05 to 6.87 GHz) for 5.0 GHz band were obtained based on the impedance bandwidth. Measured 3D pattern and gains are displayed.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.119-126
• /
• 2019

In this paper, a monopole antenna applicable to WLAN standardization is designed, fabricated, and tested. The proposed antenna is designed to have three microstrip lines based on microstrip feeding method and inserted one stub to enhance impedance characteristics. Then, it obtained triple band characteristics of the proposed antenna. We adjusted and optimized the lengths and width of the three microstrip lines and one inserted stub to obtain the required impedance bandwidth for this paper. The proposed antenna has $23.0mm(W){\times}53.1mm(L1)$ on a dielectric substrate of $24.0mm(W1){\times}60.0mm(L){\times}1.0mm$ size. From the fabrication and measurement results, bandwidths of 158 MHz (841 to 1000 MHz) for 900 MHz band, 630 MHz (2.32 to 2.95 GHz) for 2400 MHz band, and 1,040 MHz (4.95 to 5.99 GHz) for 5000 MHz band were obtained based on the impedance bandwidth. The fabricated antenna also obtained the measured gain and radiation pattern characteristics in the required triple band of the proposed antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.1 s.92
• /
• pp.84-91
• /
• 2005

In this papers, we study the characteristics of dual band PIFA(Planar Inverted F antenna) for handy phones using H-type silt in the antenna radiators. Slit types on the antenna radiator vary resonance mechanism of the antenna and affect reactance component of impedance for the antenna. Therefore the antennas resonate at the dual band(cellular -band, Korea-PCS band), the bandwidth, input impedance and radiation patterns of the proposed antenna is affected by the silt length on the radiators. In order to demonstrate the validity of the proposed theory, it is implementation the antenna of the 4 types. From results for the experiment of the implementation antenna, -5 dB bandwidth of return loss is content with the allocated bandwidth of Cellular and Korea-PCS system the gains of the antenna is about -8$\~$ - 1 dB, the radiation patterns for x-polarized or y-polarized are omnidirectional pattern. From above the results of this papers, it is conclude mobile phones antenna for handy phones using this papers results.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.1
• /
• pp.78-84
• /
• 2008

In this paper, the reconfigurable annular ring slot antenna with circular polarization diversity is proposed for SDMB(Satellite Digital Multimedia Broadcasting) system. The proposed antenna consists of a ring slot with four tuning stubs. Four PIN diodes are attached to switch circular polarization diversity. By switching the diodes ON or OFF, the proposed antenna can be operated either RHCP mode or LHCP mode. The experimental result shows that the proposed antenna has an impedance bandwidth(VSWR${\leq}$2) of 570MHz(2.47-3.04GHz) at LHCP mode, an impedance bandwidth (VSWR${\leq}$2) of 560MHz(2.45-3.01GHz) at RHCP mode, a maximum gai of 3.1dBi at RHCP mode, 4.76dBi at LHCP mode. The 3dB CP bandwidth of about 100MHz at both RHCP and LHCP mode is achieved at the center frequency 2.63GHz. The proposed antenna is suitable for application such as mobile satellite communications, WLAN(Wireless Local Area Networks), and broadband wireless communication systems.