• Advances in aircraft and spacecraft science
• /
• v.5 no.6
• /
• pp.615-632
• /
• 2018

Mechanical buckling of a rectangular functionally graded plate is obtained in the current paper using a refined higher-order shear and normal deformation theory. The impact of transverse normal strain is considered. The material properties are microscopically inhomogeneous and vary continuously based on a power law form in spatial direction. Navier's procedure is applied to examine the mechanical buckling behavior of a simply supported FG plate. The mechanical critical buckling subjected to uniaxial and biaxial compression loads are determined. The numerical investigation are compared with the numerical results in the literature. The influences of geometric parameters, power law index and different loading conditions on the critical buckling are studied.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.6
• /
• pp.58-62
• /
• 2015

When an emergency generator is running, it supplies the power for critical loads. Generator protection requires the consideration of many abnormal conditions that may occur with generators include overvoltages and ground faults. Modern day power systems create harmonics within the electrical network that can have an impact upon the associated protective system. This paper focuses on the analysing of the cause and development of a solution for the malfunction of induction disc type overcurrent ground relay by generation of harmonics during emergency generator operation.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.2
• /
• pp.28-34
• /
• 1998

Powder metallurgy processes are able to form Net-Shape products and have been widely used in the production of automobile parts to improve its productivity. However, because of pores in powder products, the toughness of powder products are generally poor. Therefore, forged products are used in parts which suffer severe fatigue loads. In this paper, the choice of powder materials and production processes such as mixing, compaction, sintering, heat treatment to produce automobile spline hub are studied. Three type of materials are selected and processed and its microstructure and properties are investigated by tensile test, compression ring test, and impact test. Materials and processing methods are selected from the results. Finally, experimental spline hubs are manufactured by selected processes from selected powders and proved by torsional durability test.

• Structural Engineering and Mechanics
• /
• v.2 no.2
• /
• pp.157-171
• /
• 1994

A general approach to the dynamic time-history analysis of the reactor core is presented in this paper as a part of the fuel assembly qualification program. Several detailed core models are set up to reflect the placement of the fuel assemblies within the core shroud. Peak horizontal responses are obtained for each model for the motions induced form earthquake. The dynamic responses such as fuel assembly deflected shapes and spacer grid impact loads are carefully investigated. Also, the sensitivity responses are obtained for the earthquake motions and the fuel assembly non-linear response characteristics are discussed.

• Proceedings of the KIEE Conference
• /
• 2000.11a
• /
• pp.95-97
• /
• 2000

In this paper, static marginal loss factors are calculated that represent the impact of marginal network losses on nodal prices at the transmission network connection points at which generators and loads are located. These static marginal loss factors are approximately calculated based on the KEPCO's expected summer peak load data of year 2000. Based on comparison analysis of marginal loss factors on generation energy resources, we can find the characteristics of each plants according to its energy resources in KOREA.

• Journal of KSNVE
• /
• v.6 no.6
• /
• pp.709-715
• /
• 1996

In recent years, the piping vibration in many Power Plants is being increased by the aged generating facilities due to a long time use. Generally, the pressure fluctuations associated with the flow-induced excitations in this case are broadband in nature. Mainly, the dominant sources of vibration are a vortex-shedding, plane waves and boundary layer turbulence. The peak level of the spectrum is proportional to the dynamic head. A severe disturbance in pipeline results in the generation of intense broadband internal sound waves which can propagate through the piping system. The characteristic frequencies of operating loads of 20%, 57%, 70%, 100% are 4 - 6 Hz and coincide with the results from impact hammering test and FEM analysis. We chose the wire energy absorbing rope restraint as a vibration reduction method after reviewing the various conditions such as site, installing space and economic cost etc. After installation, the vibration level was reduced about 54% in velocity.

• Wind and Structures
• /
• v.19 no.2
• /
• pp.185-197
• /
• 2014

Ventilation and fire safety design in road tunnels are one of the most complex issues that need to be carefully considered and analysed in the designing stage of any potential upgrade of ventilation and other fire safety systems in tunnels. Placement road tunnels space has an important influence on fire safety, especially when considering the effect of adverse wind conditions that significantly influence ventilation characteristics. The appropriate analysis of fire and smoke control is almost impossible without the use of modern simulation tools (e.g., CFD) due to a large number of influential parameters and consequently extensive data. The impact of the strong wind is briefly presented in this paper in the case of a longitudinally ventilated road tunnel Kastelec, which is exposed to various severe wind conditions that significantly influence its fire safety. The possibility of using CFD simulations in the analysis of the tunnel placement in space terms negative effect of wind influence on the tunnel ventilation is clearly indicated.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.10-14
• /
• 2006

FBG sensors are able to measure the strain of structures more easily and durable than electronic resistance gages and thus many researches are on the way to apply the FBG sensor for response monitering of infrastructures. This study investigates the deflection estimation technique using FBG sensors. Several FBG sensors are multiplexed in single optical fiber and installed. in parallel pairs along the length of the structure. The measured strains at the top and bottom of a cross section can be transferred to the curvature of the section which can be used to calculate its displacement. It has been demonstrated that the estimated deflections using the FBG sensor are compared well with the readings from displacement transducers. The results show that the proposed instrumentation technique is capable of estimating the vertical deflection of the structures for various loading conditions including impact and dynamic loads, which is crucial in the structural health monitoring.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.562-567
• /
• 2001

In this study, performance of reinforced railroad roadbeds with the slag(HMS-25) and soil were investigated through the real scale railroad roadbed tests. Several real scale reinforced railroad roadbeds were constructed in the laboratory with different subgrade conditions and were tested with the estimated actual train loads including the impact loading of train. The affecting factors such as plastic ＆ elastic settlement roadbed layers as well as surface of rails were measured. The settlement at rail surface and roadbed surface of case of soil and slag roadbed comparative with good roadbed site were 2.3, 5.7 times and 1.9, 1.6 times, respectively.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.1028-1032
• /
• 2005

Life cycle assessment(LCA) has been developed from the concept of life cycle thinking. Life cycle thinking implies that everyone in the whole chain of a product's life cycle, from cradle to grave, has a responsibility and a role to play, taking into account all the relevant external effects. LCA is an analytical tool for identifying environmental loads and assessing the environmental impact in the whole chain of a product's life cycle. In Europe and Japan, LCA and ecodesign study for railway industry have been actively carried out recently. However, LCA for railway industry in domestic is still infant. LCA is standardized in International Organization of Standardization(ISO), base on the ISO 14040 standards, 307 life cycle inventory(LCI) database for infrastructure and base materials have been established in total since 1999. Some of LCI database can use in performing LCA for trains and railway infrastructure, but still not enough to derive accurate LCA result. Therefore, railway oriented LCA methodology and LCI DB are needed to be developed.