• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.118-124
• /
• 2017

To investigate and analyze the cause of the failure of the connecting rod bolt and the crank pin bearing bolt of the diesel engine of this study, the following results were obtained through site surveying, the investigation of literature referring to similar failures, testing and inspection of the fracture surface, and the experience of the researchers. The fractured crank pin bearing bolt of the diesel engine is estimated to be damaged later than the connecting rod bolt. From the shape of fracture surface, it is evident that the failed connecting rod bolt is fractured by fatigue failure due to abnormally repeated loads (e.g. loosening of the connecting bolt, etc.), and is not failed by brittle fractures due to the impact load. The surface of the U-nut on the fractured connecting rod bolt has been worsening due to the improper use of lubricant (agent for prevention of thread fixing) and no usage of separating the each connecting rod on each cylinder. Moreover, there is the possibility that those poor surface conditions of the fractured connecting rod bolt have affected the failure of the connecting rod bolt of the main engine. And it could be assumed that the mechanical characteristic and manufacturing process of the failed connecting rod bolt and crank pin bearing bolt, which were made by a domestic company, conform to the design requirements for those bolts.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.11
• /
• pp.891-899
• /
• 2013

This paper suggests a test and evaluation procedure of conformal load-bearing antenna structure(CLAS) for high speed military jet application. A log periodic patch type antenna was designed for multi-band communication and navigation antenna. Carbon/Glass fiber reinforced polymer was used as a structure supporting aerodynamic loads and honeycomb layer was used to improve antenna performance. Multi-layers were stacked and cured in a hot temperature oven. Gain, VSWR and polarization pattern of CLAS were measured using anechoic chamber within 0.15~2.0 GHz frequency range. Tension, shear, fatigue and impact load test were performed to evaluate structural strength of CLAS. Antenna performance test after every structural strength test was conducted to check the effect of structural test to antenna performance. After the application of new test and evaluation procedure to validate a new CLAS, a design improvement was found.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.5
• /
• pp.323-334
• /
• 2020

Since boundary layer transition has a significant impact on the aero-thermodynamic performance of hypersonic flight vehicles, capability of accurate prediction of transition location is essential for design and performance analysis. In this study, γ-Re_θt model is improved to predict transition of hypersonic boundary layers and validated. A coefficient in the production term of the intermittency transport equation that affects the transition onset location is constructed and applied as a function of Mach number, wall temperature, and freestream stagnation temperature based on the similarity numerical solution of compressible boundary layer. To take into account a Mach number dependency of transition onset momentum thickness Reynolds number and transition length, additional correlation equations are determined as function of Mach number and applied to Re_θc and F_length correlations of the baseline model. The suggested model is implemented to a commercial CFD code in consideration of practical use. Analysis of hypersonic flat plate and circular cone boundary layers is carried out by using the model for validation purpose. An improvement of prediction capability with respect to variation of Mach number and unit Reynolds number is identified from the comparison with experimental data.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.12 no.3
• /
• pp.41-63
• /
• 2004

The area covered by product liability in broadest sense is so vast that an attempt to analyse all its impact on the aviation world risk. Every effort has been made to confine our review of subject a closely as possible to its influence on aircraft manufacturers, airlines and passengers, in spite of strong connections with other spheres of commercial. Product Liability in aviation is the liability of aircraft's manufacturer, processor or non-manufacturing seller for injury to the person or property of a buyer or third party caused by a product which has been sold. Here-in a product is aircraft, third party is passengers who suffered damage by defective design, defective construction, inadequate instructions for handling in aircraft. Whenever a product turns out to be defective after it has been sold, there are under Anglo-American law three remedies available against the aircraft's manufacturer (1) liability for negligence (2) breach of warranty (3) strict liability in tort. There are Under continental law Three remedies available against the aircraft's manufacturer (1) liability for defective warranty (2) liability for non-fulfillment of obligation (3) liability in tort. It is worth pointing out here an action for breach of warranty or for defective warranty, for non-fulfillment of obligation is available only to direct purchaser on the basis of his contract with the aircraft's manufacturer, which of course weakness its range and effectiveness. An action for tort offers the advantage of being available also to third parties who have acquired the defective product at a later stage. In tort, obligations are constituted not only by contract, but also by stature and common law. In conclusion, There in no difference in principle of law. In conclusion I would like to make few suggestions regarding the product liability for aircraft's manufacturer. Firstly, current general product liability code does not specify whether government offices(e.g. FAA) inspector conducted the inspection and auditory certificate can qualify as conclusive legal evidence. These need to be clarified. Secondly, because Korea is gaining potential of becoming aircraft's manufacturer through co-manufacturing and subcontracting-manufacturing with the US and independent production, there needs legislation that can harmonize the protection of both aircraft's manufacturers and their injured parties. Since Korea is in primary stage of aviation industry, considerate policy cannot be overlooked for its protection and promotion. Thirdly, because aircraft manufacturers are risking restitution like air-carriers whose scope of restitution have widened to strict and unlimited liability, there needs importation of mandatory liability insurance and national warranty into the product liability for aircraft's manufacturers. Fourthly, there needs domestic legislation of air transportation law that clearly regulates overall legal relationship in air transportation such as carrier & aircraft manufacturer's liability, and aviation insurance.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.4
• /
• pp.257-262
• /
• 2019

Lattice steel towers for overhead transmission lines have been replaced by tubular steel poles due to the visual impact of large and complex shape of truss type. Demand for tubular steel poles consisting of a single frame member continues to grow because of its advantages such as visual minimization, architectural appeal and minimal site consumptions. However, there are some constraints on the transportation and construction. As the diameter of tower base has been enlarged, it may exceed minimum height limit required to pass the tunnel in case of land transportation. Also, in a narrow place where it is not easy to secure the installation areas such as mountainous places, there might be some areas wherein it must secure a wide working space so that large vehicles and working cranes will be allowed to enter. In this paper, we presented a vertical separated tubular steel pole, which is a new type of support that can be implemented for general purpose such as mountainous areas or narrow areas to improve the issues raised by breaking away from the conventional design and fabrication methods. Technical approaches for overcoming the limit of the cross-sectional size is to separate and modularize the cross-section of the tubular steel pole designed with a size that cannot be carried or assembled, and to lighten it with a weight capable of being transported and assembled in a narrow space or mountainous area. As a result of this research, it will be possible to enter small and medium sized vehicles in locations where it is restricted to transport by large-sized vehicles. In the case of mountainous areas, it will be possible to divide it into a weight capable of being carried by a helicopter and it will be easy to adjust and fabricate it with individual modules. Furthermore, in order to break away from the traditional construction method, we proposed the equipment that can be applied to the assembly of Tubular Steel Pole without using a large crane in locations where there is no accessible road or in locations wherein large cranes cannot enter. In particular, this paper shows the movable assembling equipment and some methods that are specialized for vertical separated tubular steel pole consisting of members with reduced weight. The proposed assembly equipment is a device for assembling the body of the Tubular Steel Poles. It will be installed inside the support and the modules can be lifted by using the support itself.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.594-600
• /
• 2018

Landscape law was enacted in 2007 after the development of the Korea Planning Support System (KOPSS) in 2006. In addition, KOPSS was utilized by many local governments to improve reliability and optimization in 2010. In 2014, landscape law was fully revised, and it is likely to have a considerable impact on municipal ordinances and deliberations, which may have a considerable effect on the results of landscape reviews. This paper presents an analysis and verification of changes in the subject of deliberation by the amendment of the law and system, the method of deliberation, the composition of the scenery committee, and the introduction of KOPSS. We also propose a direction for improving the landscape deliberation system. As a result, the change of the number of deliberation items repeatedly increased and decreased due to the change of the deliberation subject and deliberation management according to the total revision of the resultant laws and institutions. In sum, it affected the deliberation decisions.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2017.04a
• /
• pp.595-597
• /
• 2017

Despite rapid growth of the global SW market, the Korean market still has a long way to go to impact global power nations. What is the reason that holds back of the No. 1 high-speed Internet country in terms of SW development? It is lack of the foundation for development of the Korean SW industry. In this context, the Korean government declared SW-oriented society and developed polices for each sector; Regarding movement that tries to apply the SW partitioning order institution in public sector to IT projects, this research aims to study SI project problems expected when conducting the SW partitioning order institution and improvements focusing on the public sector that accounts for about 30% of the entire SW industry. SW partitioning order institution is divided into planning-design and development-realization stages, which may cause problems when it is applied to SI projects. As such, the study analyzed SI projects and separate and partitioning order, exemplary cases and examples of industrial projects related to partitioning order, and drew improvement measures from institutional, technological and managerial viewpoints. The research aims to help people involved in IT projects sell SW at proper prices and improve the environment, and presents directions to create a system that strengthens competitiveness of the SW industry and SI projects by providing solutions to problems that suppliers and demanders should recognize before implementing the SW partitioning order institution.

• Journal of Korean Society of Transportation
• /
• v.32 no.2
• /
• pp.83-92
• /
• 2014

Weather condition is one of the crucial factors affecting travelers' mode choice. Nevertheless, there are numerous indefinite traffic phenomena under various weather conditions. This study was conducted to verify the hypothesis that transit riderships decrease as precipitation increases. To clarify the relationship between precipitation and transit ridership, a seemingly unrelated regression model was employed with data such as daily precipitation and daily transit riderships of 3 transit modes (bus, metro, and shuttle bus) collected in Busan for recent 24 months. The estimation results show that transit riderships decreased as the daily precipitation increased when the daily precipitation is greater or equal to 10mm/day (0.169%, 0.101%, and 0.172% reduction in bus, metro, and shuttle bus riderships, respectively, when the daily precipitation increased by 1mm). When comparing the impact of precipitation on transit riderships by modes using a cross-equation parameter restriction test, the decrease in metro ridership is relatively insensitive to the change in precipitation. However, the negative coefficient of precipitation in the metro ridership estimation model indicates that the transit users in Busan may alter their mode to taxi or automobile and/or may give up the trip itself in bad weather condition.

• Journal of Science Education
• /
• v.34 no.2
• /
• pp.193-202
• /
• 2010

This study investigated the impact of student-centered instructions on students' academic achievement in science and on their attitudes toward science. Participants included 208 middle school students. The pre- and post-test control group design was employed. The control group was designed to have traditional instructions while experimental group 1 was applied both student-centered instructions and traditional instructions, and experimental group 2 was applied student-centered instructions only. The chaper of "Stimulus and Response" was selected for this study, and students were treated for 15 hours. Data were analysed using ANOVA. Results indicated that student-centered instruction had a significant effect on students' academic achievement(p<.01). The improvement of achievement through student-centered lesson is neither depending on genders nor previous academic achievement levels. Student-centered instruction also had a significant effect on students' attitudes toward science(p< .01). Only half of the class if a student-centered lessons and improve attitudes toward science could be. The improvement of the attitudes toward science through student-centered instruction is not depending on genders. But, student-centered instruction was more effective on the average student and the lower level students than the upper level students.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.334-334
• /
• 2013

In the past decade, the infrared detectors based on intersubband transition in quantum dots (QDs) have attracted much attention due to lower dark currents and increased lifetimes, which are in turn due a three-dimensional confinement and a reduction of scattering, respectively. In parallel, focal plane array development for infrared imaging has proceeded from the first to third generations (linear arrays, 2D arrays for staring systems, and large format with enhanced capabilities, respectively). For a step further towards the next generation of FPAs, it is envisioned that a two-dimensional metal hole array (2D-MHA) structures will improve the FPA structure by enhancing the coupling to photodetectors via local field engineering, and will enable wavelength filtering. In regard to the improved performance at certain wavelengths, it is worth pointing out the structural difference between previous 2D-MHA integrated front-illuminated single pixel devices and back-illuminated devices. Apart from the pixel linear dimension, it is a distinct difference that there is a metal cladding (composed of a number of metals for ohmic contact and the read-out integrated circuit hybridization) in the FPA between the heavily doped gallium arsenide used as the contact layer and the ROIC; on the contrary, the front-illuminated single pixel device consists of two heavily doped contact layers separated by the QD-absorber on a semi-infinite GaAs substrate. This paper is focused on analyzing the impact of a two dimensional metal hole array structure integrated to the back-illuminated quantum dots-in-a-well (DWELL) infrared photodetectors. The metal hole array consisting of subwavelength-circular holes penetrating gold layer (2DAu-CHA) provides the enhanced responsivity of DWELL infrared photodetector at certain wavelengths. The performance of 2D-Au-CHA is investigated by calculating the absorption of active layer in the DWELL structure using a finite integration technique. Simulation results show the enhanced electric fields (thereby increasing the absorption in the active layer) resulting from a surface plasmon, a guided mode, and Fabry-Perot resonances. Simulation method accomplished in this paper provides a generalized approach to optimize the design of any type of couplers integrated to infrared photodetectors.