• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.75-78
• /
• 2000

There are several effective factors to influence die life in the warm forging process. For instance process design die design and die materials etc This study presented heat treatment method which could improve toughness and wear resistance simultaneously in high temperature to apply high speed tool steels like SKH51 to die material for warm forging process. To verify the feasibility of application of heat treatment method mentioned above wear test was performed under the condition of constant time in 40$0^{\circ}C$ Wear coefficient was examined to search a relation between wear amount and time for each material and heat treatment method in 30, 60, and 130 minutes. To quantify the toughness-behavior between room and high temperature impact test was performed and heat fatigue test also fulfilled to compare with the resistance of heat check in room, 200, 400, and $600^{\circ}C$ temperature. On the basis of experimental results mentioned above high speed tool steel was applied to verify appropriateness of newly proposed heat treatment method for die of rotor pole used in automobile alternator. As a result die life of high speed tool steel applied newly proposed heat treatment is longer than that of STD61.

• Steel and Composite Structures
• /
• v.22 no.5
• /
• pp.1039-1054
• /
• 2016

This paper presents the dynamic characteristics analysis of the purlin-sheet roofs by the random vibration theories. Results show that the natural vibration frequency of the purlin-sheet roof is low, while the frequencies and mode distributions are very intensive. The random vibration theory should be used for the dynamic characteristics of the roof structures due to complex vibration response. Among the first 20th vibration modes, the first vibration mode is mainly the deformations of purlins, while the rest modes are the overall deformations of the roof. In the following 30th modes, it mainly performs unilateral local deformations of the roof. The frequency distribution of the first 20th modes varies significantly while those of the following 30th modes are relatively sensitive. For different parts, the contributions of vibration modes on the vibration response are different. For the part far from the roof ridge, only considering the first 5th modes can reflect the wind-induced vibration response. For the part near the ridge, at least the first 12 modes should be considered, due to complex vibration response. The wind vibration coefficients of the upwind side are slightly higher than that of the leeward side. Finally, the corresponding wind vibration coefficient for the purlin-sheet roof is proposed.

• Journal of Drive and Control
• /
• v.12 no.4
• /
• pp.54-59
• /
• 2015

Due to the tendency to use high speed pneumatic cylinders to improve productivity, cushioning devices are adopted to decelerate the piston motion of pneumatic cylinders to reduce noise, vibration, and impact. This paper presents a comparison of the cushion characteristics of a high speed pneumatic cylinder with a relief valve type cushioning device. The system parameters selected are the damping coefficient, Coulomb friction, heat transfer coefficient, and cracking pressure of the relief valve in the air cushioning device. The integral of the time multiplied square error (ITSE) is used to quantitative measure the cushioning performance to assess the effect of varying these. The cushioning performance achieved good results when the ITSE is a minimum value. In a comparison of the piston displacement and velocity with the variations in system parameters, the heat transfer coefficients are not as significantly affected as the other. Also, the cracking pressure of the relief valve is mainly affected by the pressure and temperature in the cushion chamber.

• Journal of Korean Society of Rural Planning
• /
• v.24 no.1
• /
• pp.61-66
• /
• 2018

The purpose of this study is to identify the factors related to the heavy rain damage and to identify effect of repair and improvement for irrigation facilities on heavy rain damages. The results of the analysis are as follows. First, the imbalance of precipitation became worse over time from using the coefficient of variation. Second, the analysis using Spearman correlation coefficient shows positive relationship between heavy rain damage amount and precipitation amount, and negative correlation between heavy rain damage amount and repair and improvement for irrigation facilities cost. Third, the analysis of the panel regression model shows that the negative impact of the repair and improvement for irrigation facilities cost on the heavy rain damage, which means that the increase of the repair and improvement for irrigation facilities cost can reduce the heavy rain damage.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.142-149
• /
• 2002

The frictional properties of nylon can be improved by the impregnation of lubricants like wax, oil or graphite. The inclusion of these lubricants, on the other hand, decreases the mechanical properties of nylon, such as tensile strength, hardness and impact strength. As an attempt to maximize frictional properties, while minimizing a decrease in the mechanical properties, various kinds of nylon containing 3 wt% wax and varying contents of oil or graphite were prepared. It was found that the synergy effects to improve both friction and anti-wear properties is evidenced by impregnating a combination of wax/oil or wax/graphite. The wear rate of a nylon containing 3 wt% of wax and 1.5 wt% of oil turned out to be 1/4 of that of nylon impregnated with 8 wt% wax or 8 wt% oil. The latter showed the lowest wear rate among the nylons prepared with a single lubricant. In addition, the friction coefficient of the developed nylon was found to be very similar to the nylon with 8 wt% wax only.

• Journal of Biosystems Engineering
• /
• v.14 no.4
• /
• pp.242-250
• /
• 1989

The performance of a vertical type centrifugal distributor of granular materials was studied by means of mathematical models and experimental investigations. To develop the mathematical description of particle motion, some assumptions were made. The distribution process consisted of three stages: the entrance of a particle to the blade, the motion of the particle on the blade, and the motion of the particle in the air. The physical properties of fertilizer, which affected the particle motion, were investigated: bluk density, coefficient of friction, coefficient of restitution, and particle size distribution. The particle motion were simulated by using a computer. A prototype distributor was designed and constructed for experimental tests. The following conclusions were drawn from the computer simulation and experiment results. 1. The fertilizer may slide or roll at the point of contact when they impact on the blade and move along the blade. 2. The interaction among fertilizers may prevent them from bouncing. 3. When fertilizers roll on the blade, rolling resistance is one of the factors affecting the particle's motion. 4. The trajectory angle and position of fertilizers from a disc depend on the blade position and particle shape, but the rotating speed of the disc affected them only slightly.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.6
• /
• pp.249-255
• /
• 2005

In recent years, a novel tiny piezoelectric linear motor converting a radial mode vibration to a longitudinal mode vibration driven by the impact force has been developed for a camera optical module. The tiny piezoelectric motor is consisted of a shaft, mobile element, and piezoelectric transducer. In this work, the frictional coefficient and static friction force of the interface between the shaft and the mobile element have been investigated according to their respective materials. It was found that two combinations, namely Pyrex glass or stainless steel for the shaft and stainless steel (SUS) for the mobile element, exhibited good dynamic behaviors in the tiny ultrasonic linear motor, which was newly developed based on operating concepts based on Newton's law.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.1
• /
• pp.135-149
• /
• 1988

Friction welding has been shown to have significant economic and technical advantages. However, one of the major concerns in using friction welding is the reliability of the weld quality. No reliable nondestructive test method is available at present for detecting weld quality, particularly in a production environment. Friction welds are formed by the mechanisms of diffusion as well as mechanical interlocking. The severe plastic flow at the interface by forge action of the process brings the subsurfaces so close together that detection of any unbonded area becomes very difficult. This paper presents an attempt to determine the friction weld strength quantitatively using the ultrasonic pulse-echo method. Instead of detecting flaws or cracks at the interface, the new approach calculates the coefficient of reflection based on measured amplitudes of the echoes. It has been finally confirmed that this coefficient could provide the quantitative relationship to the weld quality such as tensile strength, torsional strength, impact value, hardness, etc. So a new nondestructive analysis system of friction weld strength of dissimilar metals using an ultrasonic technique could be well developed.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.726-728
• /
• 1998

Oil-impregnated nylons were synthesized by anionic polymerization of ${\varepsilon}$-caprolactam in the presence of mineral oils. Reaction rate and molecular weight of the product were not significantly affected by the addition of oils less than 8 phr. Physical properties such as elongation and notched impact strength were improved by the addition of oil, on the other hand hardness and tensile stress at break were slightly decreased. Oil-impregnated nylon with an oil content of 6 phr showed a minimum friction coefficient, which is only 32% compared to a friction coefficient of nylon 6 without oil.

• Food Engineering Progress
• /
• v.14 no.4
• /
• pp.354-358
• /
• 2010

The methods for determining the diffusion parameters for the diffusion of d-limonene, a major volatile compound of orange juice, through a multi-layered food packaging material and predicting its absorption into the packaging material have been investigated. The packaging material used was the 1.5-mm thick multi-layered packaging material composed of high impact polystyrene (HIPS), polyvinylidene chloride (PVDC), and low density polyethylene (LDPE). Orange juice was placed in a cell where volatiles were absorbed in the sample package and kept at $23{\pm}2^{\circ}C$ for 72 hr. The d-limonene absorbed in a 1.5-mm thick multi-layered food packaging material was analyzed by a solid phase micro-extraction (SPME). The absorption parameters for the absorption of d-limonene in the packaging material were determined and absorption of d-limonene into the packaging material was predicted using absorption storage data. The SPME desorption at $60^{\circ}C$ for 1 hr resulted in the most sensitive and reproducible results. The diffusion coefficients of d-limonene in the packaging material and the partition coefficient at $23{\pm}2^{\circ}C$ were approximately $1-2{\times}10^{12}m^2$/s and 0.03, respectively. The absorption profile no earlier than 30 hr was fit well by a model derived from the Fick's law.