• Analytical Science and Technology
• /
• v.30 no.4
• /
• pp.174-181
• /
• 2017

Bio-liquid is a liquid by-product of the hydrothermal carbonization (HTC) reaction, converting wet biomass into solid hydrochar, bio-liquid, and bio-gas. Since bio-liquid contains various compounds, it requires efficient sampling method to extract the target compounds from bio-liquid. In this research, fatty acid methyl ester (FAME) in bio-liquid was extracted based on hollow fiber supported liquid phase microextraction (HF-LPME) and determined by Gas Chromatography-Flame Ionization Detector (GC-FID) and Gas Chromatography/Mass Spectrometry (GC/MS). The well-known major components of biodiesel, including methyl myristate, palmitate, methyl palmitoleate, methyl stearate, methyl oleate, and methyl linoleate had been selected as standard materials for FAME analysis using HF-LPME. Physicochemical properties of bio-liquid was measured that the acidity was 3.30 (${\pm}0.01$) and the moisture content was 100.84 (${\pm}3.02$)%. The optimization of HF-LPME method had been investigated by varying the experimental parameters such as extraction solvent, extraction time, stirring speed, and the length of HF at the fixed concentration of NaCl salt. As a result, optimal conditions of HF-LPME for FAMEs were; n-octanol for extraction solvent, 30 min for extraction time, 1200 rpm for stirring speed, 20 mm for the HF length, and 0.5 w/v% for the concentration of NaCl. Validation of HF-LPME was performed with limit of detection (LOD), limit of quantitation (LOQ), dynamic range, reproducibility, and recovery. The results obtained from this study indicated that HF-LPME was suitable for the preconcentration method and the quantitative analysis to characterize FAMEs in bio-liquid generated from food waste via HTC reaction.

• Analytical Science and Technology
• /
• v.28 no.1
• /
• pp.40-46
• /
• 2015

Hydrochar has been generated from food waste via hydrothermal carbonization (HTC) reaction. As a solid product of HTC reaction, hydrochar has a great potential as an adsorbent of pollutants from the various media. The surface area and pore volumes are very important parameters to be served as an adsorbent. It requires an expensive equipment and consumes time to measure those parameter. Therefore, titration methods including iodine and methylene blue adsorption were evaluated to be correlated with that of BET analysis. Even though the absolute values of the computed surface area and pore volumes were not able to be matched directly, the patterns of change were successfully correlated. Among the reaction conditions, the reaction time and temperature at $230^{\circ}C$ for 4 h was determined as an optimization condition, which confirmed by titration method and BET analysis. Titration method for surface area and pore volumes computed by combination of iodine and methylene blue adsorbing values would be a simple and fast way of determining the optimization condition for hydrochar as an adsorbent produced by HTC reaction.

• Clean Technology
• /
• v.29 no.2
• /
• pp.102-108
• /
• 2023

This study applied a hydrothermal carbonization (HTC) method to carbonize sewage sludge in order to satisfy the criteria of the Waste Management Act for recycled products and to explore the possibility of recycling sludge into modification blocks. Cement was mixed with carbonized sludge generated at the optimal temperature and reaction time during HTC. After that, the compressive strengths of the modification blocks were measured by conducting both a performance and leaching test. The results of the leaching test showed that heavy metals were not detected, and the specific gravity and absorption rates were less than 1.7 and 10%, respectively, indicating that all species satisfied the criteria. The results of the compressive strength test showed that a mixing ratio of 5% and 7% with cement cured for 28 days satisfied the criteria of A, B, and C type blocks but a mixing ratio of 3% with cement did not satisfy the criteria of A type blocks after 28 days. However, after additional curing for 42 days, the mixing ratio of 3% also satisfied the A type block criteria. Therefore, the optimal mixing ratio of carbonized sludge and cement was considered to be between 3% and 5% and confirmed that the modified blocks could be utilized as aggregates.

• Carbon letters
• /
• v.16 no.2
• /
• pp.127-131
• /
• 2015

In this work, highly porous carbons were prepared by chemical activation of carbonized biomass-derived aerogels. These aerogels were synthesized from watermelon flesh using a hydrothermal reaction. After carbonization, chemical activation was conducted using potassium hydroxide to enhance the specific surface area and microporosity. The micro-structural properties and morphologies were measured by X-ray diffraction and scanning electron microscopy, respectively. The specific surface area and microporosity were investigated by $N_2$/77 K adsorption-desorption isotherms using the Brunauer-Emmett-Teller method and Barrett-Joyner-Halenda equation, respectively. Hydrogen storage capacity was dependent on the activation temperature. The highest capacity of 2.7 wt% at 77 K and 1 bar was obtained with an activation temperature of $900^{\circ}C$.