• 제목/요약/키워드: hydrogen yield

검색결과 476건 처리시간 0.026초

세리아가 첨가된 니켈/칼슘 하이드록시 아파타이트 촉매 상의 부탄 부분산화 연구 (Partial oxidation of n-butane over ceria-promoted nickel/calcium hydroxyapatite)

  • 곽정훈;이상엽;김미소;남석우;임태훈;홍성안;윤기준
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 한국신재생에너지학회 2007년도 추계학술대회 논문집
    • /
    • pp.89-92
    • /
    • 2007
  • Partail oxidation(POX) of n-butane was investigated in this research by employing ceria-promoted Ni/calcium hydroxyapatite catalysts ($Ce_xNi_{2.5}Ca_{10}(OH)_2(PO_4)_6$ ; x = $0.1{\sim}0.3$) which had recently been reported to exhibit good catalytic performance in POX of methane and propane. The experiments were carried out with changing ceria content, $O_2/n-C_4H_{10}$ ratio and temperature. As the $O_2/n-C_4H_{10}$ feed ratio increased up to 2.75, n-$C_4H_{10}$ conversion and $H_2$ yield increased and the selectivity of methane and other hydrocarbons decreased. But with $O_2/n-C_4H_{10}$ = 3.0, $n-C_4H_{10}$ conversion and $H_2$ yield decreased. This is considered due to that too much oxygen may inhibit the reduction of Ni or induce the oxidation of Ni, which results in poor catalytic activity. The optimum $O_2/n-C_4H_{10}$ ratio lay between 2.50 and 2.75. $Ce_{0.1}Ni_{2.5}Ca_{10}(OH)_2(PO_4)_6$ showed the highest $n-C_4H_{10}$ conversion and $H-2$ yield on the whole. In durability tests, higher hydrogen yield and better catalyst stability were obtained with the $O_2/n-C_4H_{10}$ ratio of 2.75 than with the ratio of 2.5.

  • PDF

매립지가스(LFG)로부터 합성가스 제조시 반응조건에 따른 수율에 미치는 연구 (A Effect of Reaction Conditions on Syngas Yield for the Preparation of Syngas from Landfill Gas)

  • 조욱상;최경돈;백영순
    • 한국수소및신에너지학회논문집
    • /
    • 제26권5호
    • /
    • pp.477-483
    • /
    • 2015
  • LFG (Land-Fill Gas) includes components of $CH_4$, $CO_2$, $O_2$, $N_2$, and water. The preparation of synthesis gas from LFG as a DME (Dimethyl Ether) feedstock was studied by methane reforming of $CO_2$, $O_2$ and steam over $NiO-MgO-CeO_2/Al_2O_3$ catalyst. Our experiments were performed to investigate the effects of methane conversion and syngas yield on the amount of LFG components over $NiO-MgO-CeO_2/Al_2O_3$ catalyst. Results were obtained through the methan reforming experiments at the temperature of $900^{\circ}C$ and GHSV of 8,800. The results were as following; it has generally shown that syngas yield increase with the increase of oxygen and steam amounts and then decrease. Highly methane conversion of above 98% and syngas yield of approximately 60% were obtained in the feed of gas composition flow-rate of 243ml/min of $CH_4$, 241ml/min of $CO_2$, 195ml/min of $O_2$, 48ml/min of $N_2$, and 450ml/min of steam, respectively, under reactor pressure of 1 bar for 200 hrs of reaction time. Also, it was shown that catalyst deactivation by coke formation was reduced by excessively adding oxygen and steam as an oxidizer of the methane reforming.

카본 블랙 촉매를 이용하는 에탄 분해에 관한 연구 (Catalytic decomposition of ethane over carbon blacks)

  • 김미소;이상엽;윤기준
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 한국신재생에너지학회 2007년도 추계학술대회 논문집
    • /
    • pp.93-96
    • /
    • 2007
  • Catalytic activities of color and conductive carbon blacks in ethane decomposition for $CO_2-free$ hydrogen production were investigated. The ethane decomposition was carried out in a conventional fixed bed reactor under atmospheric pressure at 973-1173 K for 2 hours. When the decomposition in the presence of carbon black was compared with the non-catalytic thermal decomposition, the former exhibited significantly higher ethane conversion, higher C(s) selectivity and lower ethylene selectivity with small increase of the methane selectivity, which resulted in higher hydrogen yield. This indicates that carbon black is catalytically effective for dehydrogenation of ethane as well as subsequent decomposition of ethylene. All the carbon blacks exhibited stable catalytic activity with time. In durability tests, fluffy N-330 and BP2000 maintained their activities for 36 hours.

  • PDF

혐기성 슬러지에 의한 폐수의 질소 제거에 관한 연구 (A Study on the Nitrogen Control in the Wastewater by Upflow Anaerobic Sludge Blanket.)

  • 은종극
    • 환경위생공학
    • /
    • 제12권2호
    • /
    • pp.75-81
    • /
    • 1997
  • The study was investigated with denitrification of wastewater containing nitrate using upflow anaerobic sludge blanket process. Contents of this study were the determination of nitrate removal efficiency by various hydrogen donor addition, relationship between HRT, nitrate loading rate and growth constant of microorganism in case or various hydrogen donor addition etc. Results from this study were summurized as follows. In case of adding methanol, ethanol, sodium acetate as hydrogen donor, treatability of wastewater contained 200mg/l as nitrate was about 91%. But in addition of ethanol, sodium acetate in wastewater contained 40mg/l as nitrate, nitrate removal efficiency was 80%. While the treatment of nitrate showed the yield coefficient of microorganisms(Y) as 234.8, 234.35, and 247.68 g/VSS/g nitrate, respectively, showed specific growth rate(K) as 0.885, 0.934 and 0.917 respectively.

  • PDF

대나무화학펄프의 다단표백에 관한 연구 (Studies on the Multistage Bleaching of Bamboo Chemical Pulps)

  • 강진하;박성종
    • 펄프종이기술
    • /
    • 제33권4호
    • /
    • pp.49-54
    • /
    • 2001
  • This study was carried out to acquire basic data for the bleaching of bamboo chemical pulp. Bamboo chemical pulps (alkaline sulfite (AS)-anthraquinone (AQ) pulp, Kraft pulp) were bleached with two kinds of multistage bleaching methods (CEDED, PDED) using the various kinds of bleaching agents. And, physical properties of bleached pulps were investigated. The conclusions obtained from the results were as follows; The yield of AS-AQ pulp bleached with four-stages bleaching method using the hydrogen peroxide and chlorine dioxide as a bleaching agents was higher than the other bleached pulps. The brightness of kraft pulp bleached with five-stages bleaching method using the chlorine and chlorine dioxide as a bleaching agents was higher than the other bleached pulps. The physical properties of kraft pulp bleached with four-stages bleaching method using the hydrogen peroxide and chlorine dioxide as a bleaching agents was higher than the other bleached pulps.

  • PDF

막분리 공정을 이용한 과산화수소 함유 폐액처리용 카탈라제 생산 (Catalase Production by Membrane Process for Treatment of Industrial Wastewater Containing Hydrogen Peroxide)

  • 허병옥;이동철;신현재
    • KSBB Journal
    • /
    • 제18권3호
    • /
    • pp.186-189
    • /
    • 2003
  • 본 연구는 Aspergillus niger 폐포자를 이용하여 과산화수소를 함유한 폐액처리용 효소제조 공정개발에 그 목표가 있다. 본 카탈라제 (catalase) 생산 공정은 미세여과(0.2 $\mu\textrm{m}$ microfiltration)와 한외여과 (300 KDa, 50 KDa, ultrafiltration)의 순차적인 막 여과 방식을 통하여 효소액을 회수하는 것을 특징으로 한다. 초기 폐포자와 완충액의 희석비는 1 : 5였으며 막분리 공정의 수율은 90% 이상이었다. 얻어진 카탈라제 용액의 최적 온도는 4$0^{\circ}C$, 최적 PH는 5-8 영역이었다.

Rhodopseudomonas sp. E15-1의 균체 고정화에 의한 수소생성 (Hydrogen Production by the Immobilized Cells of Rhodopseudomonas sp. E15-1)

  • Bae, Moo;Park, Sun-Hee
    • 한국미생물·생명공학회지
    • /
    • 제17권1호
    • /
    • pp.74-80
    • /
    • 1989
  • 광합성 세균의 수소생성 향상을 위한 노력의 일환으로 수소생성능이 좋은 Rhodopseudomonas E15-1 을 고정화하여 수소생성에 적당한 조건을 조사하였다. 담체로 4%의 alginate를 사용하였을 때 수소생성량이 많았으며 고정화함에 따라 산소. 질소에 대한 억제효과를 덜 받았다. Alginate 고정화 세포는 그 지름을 2mm 이하로 하는 것이 겔내로의 확산저항이 적으므로 적당했다. 여러가지 유기물을 활용하여 수소를 생성할 수 있었으며 특히 citrate, fumarate와 malate 같은 유기산의 경우 30mM의 농도가 수소생성에 있어서 적당하였다. 또한 고정화세포를 이용한 계속적인 수소생성에 있어서 20일부터 활성이 감소하기는 하나 겔의 구조적 안정성은 30일까지 유지되었다.

  • PDF

바이오 수소를 이용한 이산화탄소의 메탄 전환 연구 (CO$_2$ Conversion to Methane using Bio-hydrogen)

  • 이준철;김재형;최광근;박대원
    • 대한환경공학회지
    • /
    • 제30권9호
    • /
    • pp.933-938
    • /
    • 2008
  • 유기성 폐기물을 이용하여 생산된 수소를 환원제로 활용하여 이산화탄소를 유용한 에너지원인 메탄으로 전환시키고자 하였다. 3 개월 동안 혐기성 미생물을 이산화탄소와 수소만을 이용하여 배양하였으며, 그 결과 acetogenotrophs의 영향에 의한 메탄의 생성은 없었고, 이산화탄소를 8 mL/min으로 주입하였을 때 이산화탄소와 수소의 주입비가 1:5에서 메탄의 생성량이 2.2 m$^3$/m$^3$ day로 가장 많았으며, 이때의 이산환탄소 저감률 또한 92%로 가장 우수하였다. 회분형태로 수소 생산과 메탄발효조와의 연계실험을 통하여, 연속적으로 수소를 생산하면서 이산화탄소를 같이 메탄발효조에 주입하여, 이산화탄소의 메탄으로의 전환을 확인하였다.

벤치스케일 침출상 반응조를 이용한 음식폐기물 처리 시 신발효 및 수소발효의 거동특성 비교 (Performance comparison of acidogenic fermentation and hydrogen fermentation using bench-scale leaching-bed reactors for food waste)

  • 한선기
    • 유기물자원화
    • /
    • 제15권3호
    • /
    • pp.97-105
    • /
    • 2007
  • 본 연구는 유기성 고형폐기물 처리에 적합한 벤치스케일 침출상 반응조를 이용하여 효율적인 산발효 및 수소발효의 거동특성을 살펴보았다. 산발효조는 혐기성 소화슬러지를 식종한 후 희석율 2.0, 3.0, $4.0d^{-1}$로 운전이 되었으며, 수소발효조는 열처리된 소화슬러지를 식종한 후 희석율 2.0, 4.0, $6.0d^{-1}$로 운전이 되었다. 산발효조는 희석율 $3.0d^{-1}$에서 운전되었을 때 최대의 COD 전환율 56.2%가 얻어졌으며 이때 전환된 COD는 모두 유기산으로 전환되었다. 반면에 수소발효조는 산발효조보다 높은 COD 전환율(49.3%)을 보여주지 못했지만, 높은 에너지 수율을 가지고 있을 뿐 아니라 친환경 청정에너지인 수소가스(전체 COD 중 5.1%)를 부산물로 얻을 수 있었다. 그러므로 처리목적에 따라 산발효나 수소발효를 유기성 고형폐기물에 적용할 수 있으며, 이는 혐기성처리 기술의 경제성을 향상시킬 수 있다.

  • PDF

Can a Fermentation Gas Mainly Produced by Rumen Isotrichidae Ciliates be a Potential Source of Biohydrogen and a Fuel for a Chemical Fuel Cell?

  • Piela, Piotr;Michalowski, Tadeusz;Miltko, Renata;Szewczyk, Krzysztof W.;Sikora, Radoslaw;Grzesiuk, Elzbieta;Sikora, Anna
    • Journal of Microbiology and Biotechnology
    • /
    • 제20권7호
    • /
    • pp.1092-1100
    • /
    • 2010
  • Bacteria, fungi, and protozoa inhabiting the rumen, the largest chamber of the ruminants' stomach, release large quantities of hydrogen during the fermentation of carbohydrates. The hydrogen is used by coexisting methanogens to produce methane in energy-yielding processes. This work shows, for the first time, a fundamental possibility of using a hydrogen-rich fermentation gas produced by selected rumen ciliates to feed a low-temperature hydrogen fuel cell. A biohydrogen fuel cell (BHFC) was constructed consisting of (i) a bioreactor, in which a hydrogen-rich gas was produced from glucose by rumen ciliates, mainly of the Isotrichidae family, deprived of intra- and extracellular bacteria, methanogens, and fungi; and (ii) a chemical fuel cell of the polymer-electrolyte type (PEFC). The fuel cell was used as a tester of the technical applicability of the fermentation gas produced by the rumen ciliates for power generation. The average estimated hydrogen yield was ca. 1.15 mol $H_2$ per mole of fermented glucose. The BHFC performance was equal to the performance of the PEFC running on pure hydrogen. No fuel cell poisoning effects were detected. A maximum power density of $1.66\;kW/m^2$ (PEFC geometric area) was obtained at room temperature. The maximum volumetric power density was $128\;W/m^3$ but the coulombic efficiency was only ca. 3.8%. The configuration of the bioreactor limited the continuous operation time of this BHFC to ca. 14 h.