• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.1-10
• /
• 2020

This paper investigates the influence of the Circulating Water Channel (CWC) side wall and support struts on the hydrodynamic coefficient prediction for Autonomous Underwater Vehicles (AUVs) experiments. Computational Fluid Dynamics (CFD) method has been used to model the CWC tests. The hydrodynamic coefficients estimated by CFD are compared with the prediction of experiments to verify the accuracy of simulations. In order to study the effect of side wall on the hydrodynamic characteristics of the AUV in full scale captive model tests, this paper uses the CWC non-dimensional width parameters to quantify the correlation between the CWC width and hydrodynamic coefficients of the chosen model. The result shows that the hydrodynamic coefficients tend to be constant with the CWC width parameters increasing. Moreover, the side wall has a greater effect than the struts.

• 한국기계가공학회지
• /
• 제6권2호
• /
• pp.41-46
• /
• 2007

Butterfly valves are commonly used as control valves in applications where the pressure drops required of the valves relatively low. As the shutoff valve (on/off service) or throttling valves (for flow or pressure control), the higher order and the better precision of butterfly valves are required. The it's more and more essential to know the flow characteristic around the valve. Due to the fast progress of the flow visualization and numerical technique, it becomes possible to observe the flows around a valve and to estimate the performance of a valve. Researching these results did not gave only access to understand the process of the valve flows at different valve opening angles, but also was made to determine the accuracy of the employed method. Furthermore, the results of the three-dimensional analysis can be used in the design of butterfly valve in the industry.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.188-193
• /
• 2005

Surface texturing of tribological application is another attractive technology of friction reducing. Also, reduction of friction is therefore considered to be a necessary requirement for improved efficiency of machine. In this paper attempts to investigate the effect of density for micro-scale dimple pattern on bearing steel flat mated with pin-on-disk. We demonstrated the lubrication mechanism for a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. It is found that friction coefficient is depended on the density of surface pattern. It was thus verified that micro-scale dimple could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions from based on friction map. Lubrication condition regime has an influence on the friction coefficient induced the density of micro dimple.

• 대한조선학회지
• /
• 제11권2호
• /
• pp.7-14
• /
• 1974

Hydrodynamic moments produced by the rolling oscillation on the free surface and the associated swaying force were exactly calculated by Ursell-Tasai method for the cylinders with Kim's chine form sections($a_1,\;a_7$). The coefficient of the added moment of inertia $K_{\varphi^{\tau}}$, the progressive wave height ratio $\bar{A}$, the coefficient of swaying forces $K_{RS}$, ${\alpha}_{RS}$ of rolling oscillations are shown in the several figures. The results of the computation were compared with those of lewis form sections. It is concluded that the effect of the section form on the added moment of inertia is significant for the cylinder with the section of same beam-draft ratio and sectional area coefficient, on the other hand, a little effect appears on the wave damping.

• Environmental Engineering Research
• /
• 제19권4호
• /
• pp.345-354
• /
• 2014

In this paper, effects of physical configurations and operating conditions on bubble column performance were analyzed in terms of bubble hydrodynamic and mass transfer parameters. Bubble column with 3 different dimensions and 7 gas diffusers (single / multiple orifice and rigid / flexible orifice) were applied. High speed camera and image analysis program were used for analyzing the bubble hydrodynamic parameters. The local liquid-side mass transfer coefficient ($k_L$) was estimated from the volumetric mass transfer coefficient ($k_La$) and the interfacial area (a), which was deduced from the bubble diameter ($D_B$) and the terminal bubble rising velocity ($U_B$). The result showed that the values of kLa and a increased with the superficial gas velocity (Vg) and the size of bubble column. Influences of gas diffuser physical property (orifice size, thickness and orifice number) can be proven on the generated bubble size and the mass transfer performance in bubble column. Concerning the variation of $k_L$ coefficients with bubble size, 3 zones (Zone A, B and C) can be observed. For Zone A and Zone C, a good agreement between the experimental and the predicted $K_L$ coefficients was obtained (average difference of ${\pm}15%$), whereas the inaccuracy result (of ${\pm}40%$) was found in Zone B. To enhance the high $k_La$ coefficient and absorption efficiency in bubble column, it was unnecessary to generate numerous fine bubbles at high superficial gas velocity since it causes high power consumption with the great decrease of $k_L$ coefficients.

• 한국전산유체공학회지
• /
• 제20권2호
• /
• pp.81-87
• /
• 2015

For Underwater vehicles, Unwanted roll excursions are inevitable as they are caused by induced propeller torque, disturbances, and banking motion during turns. To estimate the manoeuvring performance of underwater vehicle, it is necessary to obtain the roll coefficient of body. This paper was covered estimation of roll coefficient of underwater vehicle using STAR-CCM+, commercial CFD(Computational Fluid Dynamics) code. The RANS equations for incompressible fluid flows was solved numerically by using a finite volume method. An MRF(Moving Reference Frame) Method was Also adopted for rotations of body. For the validation, the flow around a DARPA SUBOFF bare hull model was simulated and good agreement with experiments was obtained. And Pure roll coefficients were calculated and campared with the experimental data which were presented by Seoul National University. Finally, an underwater vehicle model with propeller was simulated and analyzed for estimation of roll coefficient variation caused by induced propeller torque.

• 제어로봇시스템학회논문지
• /
• 제2권2호
• /
• pp.121-126
• /
• 1996

The hydrodynamic coefficients estimation (HCE) is important to design the autopilot and to predict the maneuverability of an underwater vehicle. In this paper, a system identification is proposed for an HCE of an underwater vehicle. First, we attempt to design the HCE algorithm which is insensitive to initial conditions and has good convergence, and which enables the estimation of the coefficents by using measured displacements only. Second, the sensor and measurement system which gauges the data from the full scale trials is constructed and the data smoothing algorithm is also designed to filter the noise due to irregular fluid flow without changing the data characteristics itself. Lastly the hydrodynamic coefficients are estimated by applying the measured data of full scale trials to the developed algorithm, and the estimated coefficients are verified by full scale trials.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2002년도 추계학술발표회
• /
• pp.57-59
• /
• 2002

The dissolution process of NAPLs is significantly important in predicting the transport and/or fate of the contaminants and designing remedial systems. In this research, experimental observations on dissolution of TCE pool under various hydrodynamic conditions are done using an aquifer model. Hydrodynamic parameters such as linear pore velocity and dispersion coefficient are estimated from the results of preliminary tracer tests using bromide as conservative tracer before doing the TCE dissolution experiments. It is found that hydrodynamic parameters are distinctly affected by the clay lens imbeded in the aquifer model. Nonequilibrium and transient dissolution rates are observed from the results of TCE dissolution experiments.

• 융합신호처리학회논문지
• /
• 제24권2호
• /
• pp.97-102
• /
• 2023

방향타는 조선 분야에서 중요한 역할을 하기 때문에 방향타의 유체역학적 특성을 조사하기 위해 수치 시뮬레이션이 수행되었다. 유체역학적 힘과 같은 일부 값은 예인 탱크에서 쉽게 측정할 수 있지만, 실험을 통해 압력 분포, 속도 분포, 와류 발생과 같은 유동장에 대한 자세한 정보를 얻기는 어렵다. 본 연구에서는 전산유체역학(CFD)을 이용하여 방향타에 작용하는 유체역학 계수와 레이놀즈수가 미치는 영향을 연구하였다. 상용 전산유체역학 프로그램 Ansys Fluent를 이용하여 방향타 주위의 유동 특성을 연구하였고, 이때 k-epsilon 난류 모델이 사용되었다. 먼저 CFD 상용코드를 이용하여 KCS 방향타의 받음각에 따른 항력계수와 양력계수를 구하였다. 둘째, 동일한 조건에서 2차원 양력계수와 항력계수를 3차원 계수와 비교되었다. 셋째, 레이놀즈수가 유체역학적 힘에 미치는 영향이 연구되었다.

• 멤브레인
• /
• 제12권2호
• /
• pp.90-96
• /
• 2002

멤브레인 여과 실험에서 얻어진 데이터 처리에 간단한 수치해석을 적용하여 삼투압(osmotic pressure) 과 구배확산계수(gradient diffusion coefficient)를 도출하는 새로운 방법론을 제시하였다. 삼투압과 구배확산계수는 이론 및 실험적으로 쉽게 구할 수 없는 물리적 특성치로서 멤브레인 여과의 특성 규명에 중요하다. 모델 라텍스 콜로이드의 여과시간에 따른 투과플럭스(permeate flux) 값과 이에 대한 수치적분과 수치미분 데이터로부터 분산된 입자농도의 함수인 삼투압 관계식을 구했다. 이로부터 계산된 열역학적 계수(thermodynamic coefficient)는 입자농도가 증가할수록 감소하는 거동을 보였고, 여기에 기존에 제시되어 있는 수력학적 계수(hydrodynamic coefficient)를 도입하여 구배확산계수를 산출하였다. 아울러, 본 연구에서 계산된 입자농도에 따른 구배확산계수의 결과와 동일한 멤브레인과 라텍스 콜로이드의 여과에 대해서 기존에 통계역학적 시뮬레이션으로 예측한 결과를 비교하였다.