• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.687-692
• /
• 2011

Hafnium oxide ($HfO_2$) was very advantageous for substitute material of gate on existing transistor. $HfO_2$ has been widely studied due to high contact with polysilicon and thermal stability and also, it is easily etched by using HF solution. In this study, $HfO_2$ and thermal oxide films were etched by wet etch method using chemical etchant. Etch rate of $HfO_2$ and thermal oxide was linearly increased with increasing concentration of HF and temperature but etch rate of $HfO_2$ was higher than thermal oxide due to $H^+$, $F^-$, and $HF_2^-$ ions at below 0.5% concentration of HF. And also, etch selectivity was improved by adding Hydrazine as additive.

• Journal of Sensor Science and Technology
• /
• v.24 no.1
• /
• pp.41-46
• /
• 2015

In this work, pure hierarchical ZnO structure was prepared using a simple hydrothermal method, and Ag nanoparticles doped hierarchical ZnO structure was synthesized uniformly through photochemical route. The reduced graphene oxide (rGO) has been synthesized by typical Hummer's method and reduced by hydrazine. Prepared Ag/ZnO nanostructures are uniformly dispersed on the surface of rGO sheets using ultrasonication process. The synthesized samples were characterized by SEM, TEM, EDS, XRD and PL spectra. The average size of prepared ZnO microspheres was around $2{\sim}3{\mu}m$ and showed highly uniform. The average size of doped-Ag nanoparticles was 50 nm and decorated into ZnO/rGO network. The $C_2H_2$ gas sensing properties of as-prepared products were investigated using resistivity-type gas sensor. Ag/ZnO-rGO based sensors exhibited good performances for $C_2H_2$ gas in comparison with the Ag/ZnO. The $C_2H_2$ sensor based on Ag/ZnO-rGO had linear response property from 3~1000 ppm of $C_2H_2$ concentration at working temperature of $200^{\circ}C$. The response values with 100 ppm $C_2H_2$ at $200^{\circ}C$ were 22% and 78% for Ag/ZnO and Ag/ZnO-rGO, respectively. In additions, the sensor still shows high sensitivity and quick response/recovery to $C_2H_2$ under high relative humidity conditions. Moreover, the device shows excellent selectivity towards to $C_2H_2$ gas at optimal working temperature of $200^{\circ}C$.

• Proceedings of the Korean Journal of Food and Nutrition Conference
• /
• 2001.12a
• /
• pp.126-126
• /
• 2001

The Rhus verniciflua contains alkly(en)-catechol type allergens with a saiurated or unsaturated alkly chain of 15 or 17 carbon atoms. It has been recognized as an extremely active allergen causing skin reactions similar In poison ivy. The allergic contact dermatitis induced by the urushiol is known to be mediated be T lymphocytes whicht specifically recognize the hepten urushiol. Therefore. direct use of this plant as a medicinal purpose might imply a considerable hazard in Korea. In this study, using the established method for the detoxification from the stem bark of Rhus verniciflua, an strong antioxidant substance was isolated and characterized DPPH (diphenypricryl hydrazyl) assay measures hydrogen atom-donating activity and hence provides a measure of free radical scavenging antioxidant activity. DPPH, a purple-colored stable free radical, is reduced to yellow-colored diphenylpicryl hydrazine by antioxidants to deducing agents. Antioxidative effects of the water extract from RV were measured by DPPH assay. Twenty microliters of the extract was added to 1ml of 100mM DPPH solution in ethanol The mixture was shaken and left to stand for 10min at room temperature. The crude water extracts was purified by using HPLC method with a DEAE (anionic type), CN, ODS column. The purified compound remained stable at pH 3.0-6,0, but unstable above pH 6.5. It was stable heat at 10$0^{\circ}C$ for 4 hours, but still had about 80% of residual activity after treatment at 10$0^{\circ}C$ for 5 hours. The elemental composition of the HR-EI mass spectrum at m/z 170.02 was estimated the empirical formula as $C_{7}$ $H_{6}$ $O_{5}$. $C_{10}$ $H_4$ $O_2$N$_1$, $C_{5}$ $H_4$ $O_4$N$_3$, $C_{8}$$H_2O$$_1$N$_4$. In antimicrobial test, no inhibition was observed against Gram-positive and negative bacteria. This compound was stronger than that of commercial antioxidant by DPPH test, such as BHT, BHC at the same concentration (20$\mu$g/ml).ml).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.589-593
• /
• 2011

[ $SnO_2$ ]nano powders were prepared by solution reduction method using tin chloride($SnCl_2{\cdot}2H_2O$), hydrazine($N_2H_4$) and NaOH. The $SnO_2$ thick films for gas sensors were fabricated by screen printing method on alumina substrates and annealed at $300^{\circ}C$ in air, respectively. XRD patterns of the $SnO_2$ nano powders showed the tetragonal structure with (110) dominant orientation. The particle size of $SnO_2$ nano powders at the ratio of $SnCl_2:N_2H_4$+NaOH= 1:6 was about 60 nm. The sensing characteristics were investigated by measuring the electrical resistance of each sensor in a test box. Sensitivity of $SnO_2$ gas sensor to 5 ppm $CH_4$gas and 5 ppm $CH_3CH_2CH_3$ gas was investigated for various $SnCl_2:N_2H_4$+NaOH proportion. The highest sensitivity to $CH_4$ gas and $CH_3CH_2CH_3$ gas of $SnO_2$ sensors was observed at the $SnCl_2:N_2H_4$+NaOH= 1:8 and $SnCl_2:N_2H_4$+NaOH= 1:6, respectively. Response and recovery times of $SnO_2$ gas sensors prepared by $SnCl_2:N_2H_4$+NaOH= 1:6 was about 40 s and 30 s, respectively.

• Korean Journal of Materials Research
• /
• v.26 no.9
• /
• pp.468-471
• /
• 2016

$SnO_2:CNT$ thick films for gas sensors were fabricated by screen printing method on alumina substrates and were annealed at $300^{\circ}C$ in air. The nano $SnO_2$ powders were prepared by solution reduction method using tin chloride ($SnCl_2.2H_2O$), hydrazine ($N_2H_4$) and NaOH. Nano $SnO_2:CNT$ sensing materials were prepared by ball-milling for 24h. The weight range of CNT addition on the $SnO_2$ surface was from 0 to 10 %. The structural and morphological properties of these sensing material were investigated using X-ray diffraction and scanning electron microscopy and transmission electron microscope. The structural properties of the $SnO_2:CNT$ sensing materials showed a tetragonal phase with (110), (101), and (211) dominant orientations. No XRD peaks corresponding to CNT were observed in the $SnO_2:CNT$ powders. The particle size of the $SnO_2:CNT$ sensing materials was about 5~10 nm. The sensing characteristics of the $SnO_2:CNT$ thick films for 5 ppm $H_2S$ gas were investigated by comparing the electrical resistance in air with that in the target gases of each sensor in a test box. The results showed that the maximum sensitivity of the $SnO_2:CNT$ gas sensors at room temperature was observed when the CNT concentration was 8wt%.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.65-65
• /
• 2012

Copper zinc tin sulfide ($Cu_2ZnSnS_4$, CZTS) is a very promising material as a low cost absorber alternative to other chalcopyrite-type semiconductors based on Ga or In because of the abundant and economical elements. In addition, CZTS has a band-gap energy of 1.4~1.5eV and large absorption coefficient over ${\sim}10^4cm^{-1}$, which is similar to those of $Cu(In,Ga)Se_2$(CIGS) regarded as one of the most successful absorber materials for high efficient solar cell. Most previous works on the fabrication of CZTS thin films were based on the vacuum deposition such as thermal evaporation and RF magnetron sputtering. Although the vacuum deposition has been widely adopted, it is quite expensive and complicated. In this regard, the solution processes such as sol-gel method, nanocrystal dispersion and hybrid slurry method have been developed for easy and cost-effective fabrication of CZTS film. Among these methods, the hybrid slurry method is favorable to make high crystalline and dense absorber layer. However, this method has the demerit using the toxic and explosive hydrazine solvent, which has severe limitation for common use. With these considerations, it is highly desirable to develop a robust, easily scalable and relatively safe solution-based process for the fabrication of a high quality CZTS absorber layer. Here, we demonstrate the fabrication of a high quality CZTS absorber layer with a thickness of 1.5~2.0 ${\mu}m$ and micrometer-scaled grains using two different non-vacuum approaches. The first solution-processing approach includes air-stable non-toxic solvent-based inks in which the commercially available precursor nanoparticles are dispersed in ethanol. Our readily achievable air-stable precursor ink, without the involvement of complex particle synthesis, high toxic solvents, or organic additives, facilitates a convenient method to fabricate a high quality CZTS absorber layer with uniform surface composition and across the film depth when annealed at $530^{\circ}C$. The conversion efficiency and fill factor for the non-toxic ink based solar cells are 5.14% and 52.8%, respectively. The other method is based on the nanocrystal dispersions that are a key ingredient in the deposition of thermally annealed absorber layers. We report a facile synthetic method to produce phase-pure CZTS nanocrystals capped with less toxic and more easily removable ligands. The resulting CZTS nanoparticle dispersion enables us to fabricate uniform, crack-free absorber layer onto Mo-coated soda-lime glass at $500^{\circ}C$, which exhibits a robust and reproducible photovoltaic response. Our simple and less-toxic approach for the fabrication of CZTS layer, reported here, will be the first step in realizing the low-cost solution-processed CZTS solar cell with high efficiency.

• Journal of the East Asian Society of Dietary Life
• /
• v.16 no.6
• /
• pp.740-746
• /
• 2006

The proximates, vitamin C, minerals, and fatty acids of five potato cultivars were evaluated by AOAC methods, the hydrazine method, ICP-AES, and gas chromatography, respectively. The proximate analyses; vitamin C, reducing sugar, and soluble solid contents; and mineral and fatty acid compositions were significantly different among the five cultivars. The Superior cultivar contained a higher carbohydrate content and higher Ca/P ratio and lower levels of crude protein and Na. The Atlantic cultivar contained significantly higher amount of energy, carbohydrate, reducing sugar, vitamin C, SEA, and MUFA, and significantly lower amount of minerals and PUFA. The Shepody cultivar contained significantly higher amount of carbohydrate and MUFA, and significantly lower amount of soluble solid, vitamin C, and SFA. In addition, the P, Fe, Mg, Cu, and Al levels were significantly higher in Shepody, and Zn content was significantly lower. The Jopung cultivar contained significantly higher levels of moisture and Na, and significantly lower levels of soluble content, reducing sugar, carbohydrate, crude protein, and fat. Finally, the Namsuh cultivar contained significantly higher amount of soluble solid, crude protein, K, Mg, and Al, and significantly lower amount of reducing sugar.

• Journal of Powder Materials
• /
• v.12 no.3
• /
• pp.192-200
• /
• 2005

Ultrafine copper powder was prepared from $CuO-H_2O$ slurry with hydrazine, a reductant, under $70^{\circ}C$. The influence of various reaction parameters such as temperature, reaction time, molar ratio of $N_2H_4$, PvP and NaOH to Cu in aqueous solution had been studied on the morphology and powder phase of Cu powders obtained. The production ratio of Cu from CuO was increased with the ratio of $N_2H_4/Cu$ and the temperature. When the ratio of $N_2H_4/Cu$ was higher than 2.5 and the temperature was higher than $60^{\circ}C$, CuO was completely reduced into Cu within 40 min. The crystalline size of Cu obtained became fine as the temperature increase, whereas the aggregation degree of particles was increased with the reaction time. The morphology of Cu powder depended on that of the precursor of CuO and processing conditions. The average particle size was about $0.5{\mu}m$.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.708-713
• /
• 2013

Graphene oxide has been synthesized by microwave-assisted exfoliation of graphite oxide prepared by modified Hummers method. Graphite was oxidized in a solution of $H_2O_2$ and $KMnO_4$ at $65{\sim}80^{\circ}C$, followed by 10 % $H_2O_2$ solution treatment at $80{\sim}90^{\circ}C$. The graphite oxide was exfoliated under microwave irradiation of 1 kW and was reduced to graphene effectively by hydrazine hydrate ($H_4N_2{\cdot}H_2O$) treatment. The exfoliation of graphene oxide was significantly affected by the microwave irradiation on (heating)/off (cooling) period. An on/off period of 10 s/20 s resulted in much more effective exfoliation than that of 5 s/10 s with the same total treatment time of 10 min. This can be explained by the higher exfoliation temperature of 10 s/20 s. Repetition of the graphite oxidation and exfoliation processes also enhanced the exfoliation of graphene oxide. The thickness of the final graphene products was estimated to be several layers. The D band peaks of the Raman spectra of the final graphene products were quite low, suggesting a high crystal quality.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.182-185
• /
• 2012

N-doped $TiO_2$nanotubes have been newly prepared by two stage sol-gel and strong-alkali hydrothermal process using $TiCl_4$ and hydrazine/ammonia aqueous solution as raw materials. These nanotubes revealed a well developed anatase crystalline phase and perfect nanotube morphology with the diameter around 10nm and the wall thickness below 3 nm. Also, they showed a superior visible light activity and yellowish color due to the light absorption redshifted by ~35 nm and ~25 nm compared to undoped $TiO_2$ nanotubes and anatase nanoparticles, respectively.