• 통합자연과학논문집
• /
• 제4권3호
• /
• pp.238-242
• /
• 2011

For any pattern matching based algorithm in WLAN environment, the characteristics of signal to noise ratio(SNR) to multiple access points(APs) are utilized to establish database in the training phase, and in the estimation phase, the actual two dimensional coordinates of mobile unit(MU) are estimated based on the comparison between the new recorded SNR and fingerprints stored in database. The system that uses the artificial neural network(ANN) falls in a local minima when it learns many nonlinear data, and its classification accuracy ratio becomes low. To make up for this risk, the SVM/ANN hybrid algorithm is proposed in this paper. The proposed algorithm is the method that ANN learns selectively after clustering the SNR data by SVM, then more improved performance estimation can be obtained than using ANN only and The proposed algorithm can make the higher classification accuracy by decreasing the nonlinearity of the massive data during the training procedure. Experimental results indicate that the proposed SVM/ANN hybrid algorithm generally outperforms ANN algorithm.

• 제어로봇시스템학회논문지
• /
• 제19권7호
• /
• pp.633-639
• /
• 2013

Several estimation methods used in the range measurement based wireless localization area have individual problems. These problems may not occur according to certain application areas. However, these problems may give rise to serious problems in particular applications. In this paper, three methods, ILS (Iterative Least Squares), DS (Direct Solution), and DSRM (Difference of Squared Range Measurements) methods are considered. Problems that can occur in these methods are defined and a simple hybrid solution is presented to solve them. The ILS method is the most frequently used method in wireless localization and has local minimum problems and a large computational burden compared with closed-form solutions. The DS method requires less processing time than the ILS method. However, a solution for this method may include a complex number caused by the relations between the location of reference nodes and range measurement errors. In the near-field region of the complex solution, large estimation errors occur. In the DSRM method, large measurement errors occur when the mobile node is far from the reference nodes due to the combination of range measurement error and range data. This creates the problem of large localization errors. In this paper, these problems are defined and a hybrid localization method is presented to avoid them by integrating the DS and DSRM methods. The defined problems are confirmed and the performance of the presented method is verified by a Monte-Carlo simulation.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1999년도 학술발표대회 논문집 제18권 1호
• /
• pp.103-108
• /
• 1999

The aim of the work described in this paper is to develop a complex underground acoustic system which detects and localizes the origin of an underground hammering sound using an array of hydrophones located about loom underground. Three different methods for the sound localization will be presented, a time-delay method, a power-attenuation method and a hybrid method. In the time-delay method, the cross correlation of the signals received from the array of sensors is used to calculate the time delays between those signals. In the power-attenuation method, the powers of the received signals provide a measure of the distances of the source from the sensors. In the hybrid method, both informations of time-delays and power-ratios are coupled together to produce better performance of position estimation. A new acoustic imaging technique has been developed for improving the hybrid method. This new acoustic imaging method shows the multi-dimensional distribution of the normalized cost function, so as to indicate the trend of the minimizing direction toward the source location. For each method the sound localization is carried out in three dimensions underground. The distance between the true and estimated origins of the source is 28m for a search area of radius 250m.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.149-152
• /
• 1999

The aim of the work described in this paper is to develop a complex underground acoustic system which detects and localizes the origin of an underground hammering sound using an array of hydrophones located about loom underground. Three different methods for the sound localization will be presented, a time-delay method, a power-attenuation method and a hybrid method. In the time-delay method, the cross correlation of the signals received from the way of sensors is used to calculate the time delays between those signals. In the power-attenuation method, the powers of the received signals provide a measure of the distances of the source from the sensors. In the hybrid method, both informations of time-delays and power-ratios are coupled together to produce better performance of position estimation. A new acoustic imaging technique has been developed for improving the hybrid method. For each method the sound localization is carried out in three dimensions underground. The minimum distance between the true and estimated origins of the source is 28 m for a search area of radius 250m.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.464-470
• /
• 2011

In this paper, the feasibility of applying a position sensorless control technique to hybrid electric vehicles (HEVs) is practically evaluated. The proposed position estimator has a straightforward structure with properties that combines the model and the saliency tracking-based rotor position estimation for interior permanent magnet synchronous motors (IPMSMs). The proposed method can be used in the event of sensor loss or sensor recovery to sustain continuity of operations. The developed system takes into account the estimated position transition between two distinct sensorless methods. The transition is enhanced by introducing a synchronized transition algorithm based on a single tracking observer. Extensive experimental results are presented to verify the principles and show a reliable estimation performance over the entire speed range including standstill under 150% load conditions.

• 조명전기설비학회논문지
• /
• 제25권5호
• /
• pp.22-33
• /
• 2011

An induction motor operated with a conventional direct self controller(DSC) shows a sluggish response during startup and under changes of torque command. Fuzzy logic controller(FLC) is used in conjection with DSC to minimize these problems. A FLC chooses the switching states based on a set of fuzzy variables. Flux position, error in flux magnitude and error in torque are used as fuzzy state variables. Fuzzy rules are determinated by observing the vector diagram of flux and currents. This paper proposes hybrid fuzzy controller for direct torque control(DTC) of induction motor drives. The speed controller is based on adaptive fuzzy learning controller(AFLC), which provide high dynamics performances both in transient and steady state response. Flux position, error in flux magnitude and error in torque are used as FLC state variables. The speed is estimated with model reference adaptive system(MRAS) based on artificial neural network(ANN) trained on-line by a back-propagation algorithm. This paper is controlled speed using hybrid fuzzy controller(HFC) and estimation of speed using ANN. The performance of the proposed induction motor drive with HFC controller and ANN is verified by analysis results at various operation conditions.

• 전력전자학회논문지
• /
• 제12권4호
• /
• pp.324-331
• /
• 2007

본 연구에서는 슬라이딩 모드 관측기를 사용한 리튬 배터리의 충전량 예측방법에 대해서 논의한다. 배터리의 비선형 회로 모델링 기법이 소개되고 슬라이딩 모드 관측기를 사용한 충전량 예측기의 설계 방법이 논의된다. 기존의 복잡한 배터리 모델링 방법 대신, 단순화된 저항-커패시터 모델링 방법이 본 연구에서 사용되었다. 단순화된 모델에 의해 발생되는 오차나 불확실성은 슬라이딩 모드 관측기에 의해 보상되었다. 슬라이딩 모드 관측기의 구조는 단순하지만, 모델링 에러나 외란에 대해서 강인한 특성을 보여준다. 제안된 제어기의 수렴성은 등가제어 방법에 의해서 증명되었다. 제안된 시스템의 성능은 UDDS (Urban Dynamometer Driving Schedule) 시험에 의해서 증명되었다. 시험 결과 제안된 시스템은 실제 주행 환경에서도 우수한 추적 성능을 보여주었다.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3242-3249
• /
• 2022

As Kori unit 1 is undergoing the decommissioning process, estimating the disposal amount of waste from the decommissioned nuclear reactor has become one of the challenging issues. Since the waste disposal amount estimation depends on the packing of the waste, it is highly desirable to optimize the waste packing plan. In this study, we developed an efficient scheme for packing waste component segments. The scheme consists of 1) preparing three-dimensional models of segments, 2) orienting each segment in such a way to minimize the bounding box volume, and 3) applying hybrid genetic algorithm to pack the segments in the disposal containers. When the packing solution converges in the algorithm, it comes up with the number of containers used and the placement of segments in each container. The scheme was applied to Kori-1 reactor pressure vessel. The required number of containers calculated by the developed scheme was 24 compared to 42 that was the estimation of the prior packing plan, resulting in disposal volume savings by more than 40%. The developed method is flexible for applications to various packing problems with waste segments from different cutting options and different sizes of containers.

• 한국통신학회논문지
• /
• 제42권5호
• /
• pp.967-974
• /
• 2017

본 논문에서는 FTN (faster-than-Nyquist) 시스템에서 MAP (maximum a posteriori) 기법을 이용한 ISI(inter-symbol interference) 추정 기법을 제안한다. 제안하는 기법은 FTN 전송으로 인한 ISI를 제거하기 위하여 복조기에서 MAP 기법을 이용하여 복조를 수행한다. 또한 매우 큰 구현 복잡도를 갖는 MAP 기법의 단점을 보안하기 위하여 간단하게 구현 가능한 SIC (successive interference cancellation) 기법과 MAP 기법을 연동하여 낮은 복잡도를 가지면서도 우수한 성능을 나타내는 ISI 제거 기법을 제안한다. 제안하는 기법은 MAP 기법과 비교하였을 때 낮은 복잡도를 가질 뿐만 아니라 기존에 제안된 ISI 추정 기법들보다 우수한 추정 성능을 나타내는 장점이 있다.

• 대한기계학회논문집B
• /
• 제28권6호
• /
• pp.705-712
• /
• 2004

An inverse boundary analysis of surface radiation in an axisymmetric cylindrical enclosure has been conducted in this study. Net energy exchange method was used to calculate the radiative heat flux on each surface, and a hybrid genetic algorithm was adopted to minimize an objective function, which is expressed by sum of square errors between estimated and measured or desired heat fluxes on the design surface. We have examined the effects of the measurement error as well as the number of measurement points on the estimation accuracy. Furthermore, the effect of a variation in one boundary condition on the other boundary conditions was also investigated to get the same desired heat flux and temperature distribution on the design surface.