• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.11
• /
• pp.912-917
• /
• 2001

In this study, we define the measuring method of crank angle precisely using an event and perform a study on the hardware structure and software algorithms which is applicable for the commercial engine. Also we developed a Computer-ECU(Personal computer based electronic control unit) using a computer and a microprocessor, for performing the ignition at a desire position(angle) and for controlling a duty ratio a pulse for ISC(Idle speed control). We applied these algorithms to the modeling which is induced a concept of event and got a better result than a conventional ECU in the state of transient as a result of performing air fuel ratio control in a commercial engine. This technique can be used for the back to improve ECU performance. It the present type of Hybrid I. C voltage regulator is altered to the new type of regulator, we will be surely able to reduce the production cost as well as simplify the design of alternator\`s rear bracket and rectifier part because of the removal of trio diode. Experiment is taken by MS-R004.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.15-19
• /
• 2006

A pulsed laser ablation deposition (PLAD) technique is an excellent method for the fabrication of amorphous carbon (a-C) films, because it can generate highly energetic carbon clusters on a substrate. This paper was focused on the understanding and analysis of the motion of C particles in laser ablation assisted by Ar plasmas. The simulation has carried out under the pressure P=50 mTorr of Ar plasmas. Two-dimensional hybrid model consisting of fluid and Monte-Carlo models was developed and three kinds of the ablated particles which are carbon atom (C), ion ($C^+$) and electron were considered in the calculation of particle method. The motions of energetic $C^+$ and C deposited upon the substrate were investigated and compared. The interactions between the ablated particles and Ar gas plasmas were discussed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.2
• /
• pp.168-175
• /
• 2003

A new algorithm based on Genetic Algorithms is proposed f3r solving process optimization problems formulated in MINLP, GDP and hybrid MINLP/GDP. This work is focused especially on the design of the Genetic Algorithm suitable to handle disjunctive programming with the same level of MINLP handling capability. Hybridization with the Simulated Annealing is experimented and many heuristics are adopted. Real and binary coded Genetic Algorithm initiates the global search in the entire search space and at every stage Simulated Annealing makes the candidates to climb up the local hills. Multi-Niche Crowding method is adopted as the multimodal function optimization technique. and the adaptation of probabilistic parameters and dynamic penalty systems are also implemented. New strategies to take the logical variables and constraints into consideration are proposed, as well. Various test problems selected from many fields of process systems engineering are tried and satisfactory results are obtained.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.129-135
• /
• 2017

This paper introduces a design and a simulation of a hybrid active power filter (HAPF) for harmonics reduction given an ideal supply source. The synchronous reference frame method has been used here to identify the reference currents. The proposed HAPF uses a new artificial- intelligence technique called Particle Swarm Optimization (PSO) for tuning the parameters of a proportional and integral controller called PI-PSO. The PI-PSO controller is used to archive optimality for the DC-link voltage of the HAPF-inverter. The hysteresis non-linear current control method is used in this approach to compare the extracted reference and the actual currents in order to generate the pulse gate required for the HAPF. Results obtained by simulations with Matlab/Simuling show that the proposed approach is very flexible and effective for eliminating harmonic currents generated by the non-linear load with the HAPF based PSO tuning.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.24 no.2
• /
• pp.1-15
• /
• 1999

This research involves the development and evaluation of a work flow control model for a type of flexible manufacturing system(FMS) called a flexible flow line(FFL). The control model can be considered as a kind of hybrid intelligent model in that it utilizes both computer simulation and neural network technique. Training data sets were obtained using computer simulation of typical FFL states. And these data sets were used to train the neural network model. The model can easily incorporate particular aspects of a specific FFL such as limited buffer capacity and dispatching rules used. It also dynamically adapts to system uncertainty caused by such factors as machine breakdowns. Performance of the control model is shown to be superior to the random releasing method and the Minimal Part Set(MPS) heuristic in terms of machine utilization and work-in-process inventory level.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.8
• /
• pp.600-609
• /
• 2003

A hybrid stabilization approach involving both Passivity Observer/passivity Controller and wave variables is addressed to stabilize the teleoperation system with time delay. To guarantee the stability of master or slave side, Passivity Observer and Passivity Controller are applied. But Passivity Observer and Passivity Controller technique cannot deal with communication delay and even small communication delay cause the system to be unstable. To cope with this problem, wave variables are additionally employed to have robustness to arbitrary delays. To show the validity of our proposed approach, several computer simulation results are illustrated.

• Structural Monitoring and Maintenance
• /
• v.9 no.2
• /
• pp.179-200
• /
• 2022

This paper proposes a data-driven methodology for online early damage identification under changing environmental conditions. The proposed method relies on two data analysis methods: feature-based method and hybrid principal component analysis (PCA) and kernel PCA to separate damage from environmental influences. First, spectral sub-band features, namely, spectral sub-band centroids (SSCs) and log spectral sub-band energies (LSSEs), are proposed as damage-sensitive features to extract damage information from measured structural responses. Second, hybrid modeling by integrating PCA and kernel PCA is performed on the spectral sub-band feature matrix for data normalization to extract both linear and nonlinear features for nonlinear procedure monitoring. After feature normalization, suppressing environmental effects, the control charts (Hotelling T² and SPE statistics) is implemented to novelty detection and distinguish damage in structures. The hybrid PCA-KPCA technique is compared to KPCA by applying support vector machine (SVM) to evaluate the effectiveness of its performance in detecting damage. The proposed method is verified through numerical and full-scale studies (a Bridge Health Monitoring (BHM) Benchmark Problem and a cable-stayed bridge in China). The results demonstrate that the proposed method can detect the structural damage accurately and reduce false alarms by suppressing the effects and interference of environmental variations.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.336-341
• /
• 2004

In this paper, a hybrid stabilization approach involving both passivity observer/passivity controller and wave variables is addressed to stabilize a teleoperation system with fixed time delay. To guarantee the stability of master or slave side, passivity observer/passivity controller are applied. But, passivity observer/passivity controller cannot deal with communication delay, and thus even small communication delay cause the system to be unstable. To cope with this problem, wave variables are additionally employed to have robustness to fixed communication delays. To show the validity of our proposed approach, several computer simulation results are illustrated.

• 전기의세계
• /
• v.25 no.6
• /
• pp.89-96
• /
• 1976

In this paper we deal with that the performance indices by the three adaptive sampling control laws are computed and compared. It shows that the most effective control law is the integral input difference method. The techniques of simulation by Analog/Hybrid computer are presented and the results of the output illustrate that the maximum and minimum sampling interval can be applied to the time sharing of digital controller or computer.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.471-476
• /
• 1993

In this paper we proposed the digital implementation of an $H^{\infty}$-optimal controller using lifting technique and $H^{\infty}$-control theory. The discrete controller is obtained through iterative adjustment of sampling time and weighting function, which can ber performed by computing the L$_{2}$-induced input to output norm of the sampled-data system with bandlimited exogenous input. The resulting sampled-data bandlimited exogenous input. The resulting sampled-data system is stable and the performance including inter-sampling behaviour of the hybrid system can be also optimized.d.