• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.2
• /
• pp.62-66
• /
• 2016

In this study, it was investigated that characteristic of crack-self-healing of hot-pressed SiC. SiC ceramics was sintered with $Al_2O_3$ and $Y_2O_3$ sintering additive by hot press. Sintering was performed in hot-press furnace in flowing argon (Ar), holding for 3 hr under $1950^{\circ}C$ and 50 MPa. The sintered SiC was machined into 3-point bending strength specimen of $3{\times}4{\times}40mm$, and introduced pre-crack by Vickers indentation at 49.6 N. Specimens were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), 3-point bending strength after heat treatment at $1200{\sim}1400^{\circ}C$ for 1~10 hr. The best crack-self-healing ability was achieved 770 MPa 3-point bending strength by heat treatment at $1300^{\circ}C$ for 5 hr.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.370-373
• /
• 2008

Small size gas turbine disk requires good mechanical strength and creep properties at high temperature. In this study, Waspaloy was used as a superalloy to satisfy these specifications. The control of microstructure was needed to satisfy material properties at high temperature. In order to do this, we studied forging conditions and material analysis. Therefore die and preform design conducted so that hot forged gas turbine disk could have a good microstructure. The die and preform shapes are designed with consideration of the predefined hydraulic press capacity and the microstructure of forging product. Also we carried out the hot compression test for Waspaloy in various test conditions. From these results, we obtained the forging conditions as material temperature, die velocity etc. To verify these forging conditions, we conducted FE simulations by means of the DEFORM 2D-HT. In this study, the hot closed die and preform designs were completed to offer high temperature material properties of a small size gas turbine.

• Transactions of Materials Processing
• /
• v.1 no.1
• /
• pp.20-32
• /
• 1992

This paper describes some research of Computer-Aided Process Planning and Die Design of Hot Forging for axisymmetric parts produced by the press. An approach to the system is based on knowledge based system. The system has been written in AutoLisp with personal computer. Knowledges for process planning & die design are extracted from the plasticity theories, handbooks, relevent references and empirical know-how of field experts in hot forging companies. The developed system is composed of five main modules, such as input module, process planning module, die design module, flow simulation module and output module which are used independently or in all. The final output is generated in graphic from. The developed system which aids designer provides powerful capabilities for process planning and die design of hot forging. This system also provides approximate flow pattern.

• 연구논문집
• /
• s.30
• /
• pp.15-23
• /
• 2000

In this study, develop the thermal pump using water evaporation and condensation. Vapor from heating room moves up to pumping room and press the water of pumping room. Consequently water is pumped out to water tank. Then hot vapor direct contact with cold water in condensing room after pumping process. At this time, pressure of condensing room is down to-5kPa and suck in water of tank. This pump executes self ping and good durability because of no mechanical moving parts. Thermal pump is pumped cyclic so that, this pump is not used single. Therefore thermal pump of hot water boiler used to multi-stage for stable pumping rate. As the result of performance test, the developed thermal pump proves pumping action of water evaporation/condensation. And total volume flow rate is 500liter during one hour. If three thermal pump is installed parallel, this pump can use to the hot water boiler in the 300,000kcal/h class.

• Structural Engineering and Mechanics
• /
• v.19 no.3
• /
• pp.261-279
• /
• 2005

The hot spot stress approach is usually adopted in the fatigue design and analysis of tubular welded joints. To apply the hot spot stress approach for fatigue evaluation of long span suspension bridges, the FEM is used to determine the hot spot stress of critical fatigue location. Using the local finite element models of the Tsing Ma Bridge, typical joints are developed and the stress concentration factors are determined. As a case for study, the calculated stress concentration factor is combined with the nominal representative stress block cycle to obtain the representative hot spot stress range cycle block under traffic loading from online health monitoring system. A comparison is made between the nominal stress approach and the hot spot stress approach for fatigue life evaluation of the Tsing Ma Bridge. The comparison result shows that the nominal stress approach cannot consider the most critical stress of the fatigue damage location and the hot spot stress approach is more appropriate for fatigue evaluation.

• Journal of Technologic Dentistry
• /
• v.25 no.1
• /
• pp.21-28
• /
• 2003

The purpose of this study was to process bio-active glass ceramic composite, reinforced with sapphire fibers, by hot press. Also to study the interface of the matrix and the sapphire fiber, and the mechanical properties. Glass raw materials melted in Pt crucible at 1300$^{\circ}C$ during 3.5 hours. The melt was crushed in ball mill and then crushed material, ground and sieved to $<40{\beta}{\mu}m$. Sapphire fibers cut (30mm) and aligned. Powder and fibers hot pressed. The micrographs show good bonding between the matrix and the fiber and no porosity in the glass matrix. This means ideal fracture phenomena. Glass is fractured before the fiber. This is indication of good fracture strength. EDXS showing aluminum rich phase and crystalline phase. Bright field image of the matrix showing crystalline phase. Also diffraction pattern of TEM showing the crystalline phase and more than one phase. Strength of the samples was determined by 3 point bend testing. Strength of the 10vol% sample was approximately 69MPa, while strength of the control sample is 35MPa. Conclusions through this study as follow: 1. Micrographs show no porosity in the glass matrix and the interface. 2. The interface between the fiber and the glass matrix show no gaps. 3. Fracture of the glass indicates characteristic fiber-matrix separation. 4. Presence of crystalline phase at high processing temperature. 5. Sapphire is compatible with bioactive glass.

• Transactions of Materials Processing
• /
• v.32 no.3
• /
• pp.114-121
• /
• 2023

During rolling, rolling mill rolls endure wear when shaping metal billets into a desired form, such as bars, plates, and shapes. Such wear affects the lifespan of the rolls and product quality. Therefore, in addition to rigidity, wear performance is a key factor influencing the performance of rolling mill rolls. Conventional methods such as casting and forging have been used to manufacture rolling mill rolls. However, powder alloying methods are increasingly being adopted to enhance wear resistance. These powder manufacturing methods include atomization, canning to shape the powder, hot isostatic pressing to combine the powder alloy with conventional metals, and various wear performance tests on rolls prepared with powder alloys. In this study, numerical simulations and experimental tests were used to develop and elucidate the wear analysis mechanism of rolling mill rolls. The wear characteristics of the rolls under various rolling conditions were analyzed. In addition, experimental tests (wear and surface analysis tests) and wear theory (Archard wear model) were used to evaluate wear. These tests were performed on two different materials in various powder states to evaluate the different aspects of wear resistance. In particular, this study identifies the factors influencing the wear behavior of rolling mill rolls and proposes an analytical approach based on the actual production of products. The developed wear analysis mechanism can serve the future development of rolls with high wear resistance using new materials. Moreover, it can be applied in the mechanical and wear performance testing of new products.

• Korean Journal of Materials Research
• /
• v.7 no.4
• /
• pp.267-275
• /
• 1997

본 연구에서는 암석폐재를 대상으로 직경이 60mm인 고화체를 얻을 수 있는 수열 hot press 장치를 개발하였고, 고형화를 위한 최적조건을 찾아내는 내용을 다루었다. 이어 고화체의 기계적 성질을 평가하였고, 고화기구와 미시적 파괴거동을 규명하기위하여 SEM관찰 및 음향방출실험을 실시하였다. 고형화를 위한 최적조건은 NaOH용액이 10wt%, 수열온도가 30$0^{\circ}C$이고, 유지시간이 1시간이었다. 또한 수열반응동안에 다양한 제 2화합물들이 생성되었으며, 이들은 고화체의 기계적 성질에 큰 영향을 미쳤다. 아울러 원석의 경우에는 AE Counts가 초기화중에서부터 나타났으나, 고화체는 초기하중에서 전혀 AE Counts가 검출되지 않았다. 이와같은 사실로부터 수열 hot press법에 의해 얻어진 고화체는 원석과는 다르게 암석 입자간의 결합이 보다 치밀하게 이루어지고 있음을 유추할 수 있다.

• Journal of the Korean Ceramic Society
• /
• v.32 no.6
• /
• pp.653-658
• /
• 1995

Directional effect of applied pressure during sintering on the microstructure and fracture toughness of the heat-treated silicon nitride ceramics has been investigated. The specimens with a composition of 92Si3N4-8Y2O3(in wt%) were sintered at 172$0^{\circ}C$ by a hot press (HP ) and a hot isostatic press (HIP) and heat-treated for grain growth at 1800~20$0^{\circ}C$. The fracture toughness of the HP samples increased with the grain size while the fracture toughness of the HIP treated samples remained the same even though the grain growth occurred. This discrepancy was explained by a bimodal grain size distribution and large aspect ratio of the HPed samples and a monomodal grain size distributjion and samll aspect ratio of the HIP treated samples.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1020-1022
• /
• 2005

We have fabricated a high electron source from carbon nanotubes (CNTs) using hot-press method. Using hot-press method, we are able to control the tube density and the morphology of CNT films. We propose that the high emission current is due to the solid adhesion between the CNTs and substrates and uniform morphology of CNT film.