• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1156-1159
• /
• 2017

The various ground support equipments are necessary for KSLV-II ground operation at the assembly building located in Naro Space Center. Among the various ground support equipments, the launch vehicle connection unit and high pressure flexible hose are important elements, because they are used for connection between the ground compressed gas supply system and the launch vehicle. In this paper, the development progress of the launch vehicle connection unit and high pressure flexible hose are introduced.

• Korean Journal of Computational Design and Engineering
• /
• v.10 no.1
• /
• pp.40-48
• /
• 2005

A hydraulic hose is an important part of the hydraulic system which transmits power using pressurized fluids. It allows relative motion between components at each end of the hose assembly, and it is much easier to route a hose assembly than it is to bend and install a rigid tubing assembly. Unnecessary loads, which drop the hose's pressure capability and shorten service life, depend on a hose-routing. Therefore, the Hydraulic system designers must be aware to consider unnecessary load does not affect the here. For this consideration in an early stage of the design process, CAD system must support the hose assembly routing design function which is to generate routing path and design fitting angle properly. This paper proposes 2 methods. One is to generate curves that are similar to routing paths of the real hose assembly using the energy minimization method and the optimization method. The other is to design fitting angles that are important design elements of a hose assembly using the Parallel Transport Frame. To implement the proposed methods above, commercial CAD software, CATIA has been integrated with our program.

• Journal of KSNVE
• /
• v.6 no.5
• /
• pp.671-677
• /
• 1996

This paper presents the analytical method for predicting turbulence- induced noise in the multilayered cylinder composed of an outer hose, an inner fluid and an internal core. It is assumed that an infinite axisymmetric cylinder is located horizontally in water with free stream velocity and the turbulent boundary layer (TBL) surrounding the outer hose is fully developed and homogeneous. The transfer function at the core surface due to the propagation of the pressure fluctuation within the TBL is formulated using the linearized Navier-Stockes equation for solid and fluid. In the estimation of the energy spectrum of wall pressure fluctuation, the empirical formula proposed by Strawderman based on the Corcos model is used. A general algorithm for the calculation of the pressure level at the surface of a core, that is, turbulence- induced noise, is presented. Through the detailed numerical simulation, it is found that the major noise mechanism is the propagation of the bulge wave along hose.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.3
• /
• pp.22-28
• /
• 1998

This paper presents experimental investigations on the attenuation characteristics of pressure ripple in automotive power steering hydraulic hoses. Also, a mathematical model of hydraulic hoses is proposed to support design of the power steering hydraulic circuit and analyze the attenuation characteristics of pressure ripples. The experimental results show that the pulsation attenuation characteristics of hydraulic hoses is remarkably affected by the flexible metal tube inserted coaxially inside a hydraulic hose with a finite length as well as viscoelastic properties of hose wall. It is also shown that the predicted results by the model proposed here agree well with the measured results over a wied range of frequency.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.14 no.3
• /
• pp.2697-2702
• /
• 1972

Controlling insects and diseases is an important factor for increasing yields of agricultural products. Power sprayer is widely used in cooperative controlling of insects and diseases for the production of rice and fruits. However, farmers need a long hose to use the power sprayer and that presently most of the farmers have hose made abroad. This study was designed to test the change of outside diameter and unit Iength, and to measure the pressure Ioss for three different kinds of hoses made domestically and one made in Japan. The resulte are as follows; 1. The three kinds of Korean-made hoses showed an increase in the length and a decrease in the outside diameter as the spraying pressure increase. The rate of change of the length ranged from 3.5% to 1.6% and the rate of change of the outside diameter from 3.5% to 1.4% respectively. 2. As the length of hose increases, the pressure loss was $3kg/cm^2$ at the end of a 100m of the hose made in Japan, while it was $7-10kg/cm^2$ for Korean-made hoses. 3. The Korean-made hoses were not broken under $27-28kg/cm^2$ of spraying pressure. 4. As a conclusion, the Korean-made hoses can safely be used under continuous rated pressure of the power sprayer, but they can not properly be used for the case of cooperative controlling system where a long hose is reguired because of the heaviness of the hoses and the narrowness of the inside diametar. Hence, it is highly recommended to improve the Korean-made hoses to be used for such a situation.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.5
• /
• pp.369-374
• /
• 2021

Apartment recently built in kitchen is made is made because the gas hose with built-in ways invisible inside the sink. In this case, if the gas leaks, it is a dangerous method that can accumulate inside the sink and lead to an explosion. In this study, since the hose connected between the gas range and the intermediate valve is inside the sink, it is not possible to test for gas leaks, so a valve system that can easily check for gas leaks using a pressure sensor was studied. As for the pressure measurement method, the pressure of the hose connecting the intermediate valve and the gas range was measured so that data could be collected and analyzed using the I2C communication method. In addition, the calculation of the gas pressure supplied to the home was investigated for the atmospheric pressure error for the value calculated by adding the average value of the gas gauge pressure of 22.46 mbar at the inlet of the gas meter to the atmospheric pressure. A valve system was developed to detect minute gas leaks.

• Journal of Biosystems Engineering
• /
• v.7 no.2
• /
• pp.30-35
• /
• 1983

To investigate the factors affecting the transportability of spray droplets, the maximum distance, the effective distance, the ratio of even distribution, and the diameters of particles were measured in accordance with the different pressure levels of power sprayer using 3 hole swath type nozzle, and the results are summerized as follows; 1. The distance of the most dense point from the nozzle was shortened by 0.5 meter with the 100-meter-long hose. The maximum reaching distances were reduced by 1.5 and 1.0 meters for the 13m/m and the 8.5 m/m hoses respectively, and the effective distance were reduced by 0.5 meter for both cases. 2. The effective distance can not be extended beyond 14 meters even if the length of hose is minimized at the rated pump pressure 28 kg/$cm^2$, it was 1 meter longer for 13m/m hose compared to the 8.5m/m one. 3. In case of 13m/m hose, the most dense point can be extended further by 0.5 meter increasing the pump pressure by 8 kg/$cm^2$, and the maximum distance and effective distance were increased by 2.0 and 0.5 meters respectively. There was no significant effect of pressure changes on the transportability in case of 8.5m/m hose. 4. Both the reduction of hose length and the increase of pump pressure influenced in large extent to the atomization effect of droplets. It was noticed that the diameter of droplet is related to the pump pressure and inside diameter of hose. 5. The pressure drop in 100-meter-long and l3m/m hose was 5~7kg/$cm^2$ at the pump pressure range of 25~33kg/$cm^2$, and it is an equivalent of 2% per 10 meter length of hose.

• Journal of Power System Engineering
• /
• v.2 no.1
• /
• pp.45-51
• /
• 1998

An analyzing method for pressure fluctuations in oil hydraulic pipe network was developed in this study. The object pipe network has multi-branch configuration, and the pipelines of it are composed of metal tubes and flexible hoses. Transfer matrix method, in other words impedance method, was used for the analysis. Values of physical parameters describing the characteristics of flexible hose were measured by experiments and reflected to the analysing procedure. The reliability and usefulness of the analyzing method were confirmed by investigating computed results and experimental results got in this study.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.886-892
• /
• 2013

Hydraulic hose assemblies are used as piping components for construction machinery, automobile, aircraft, industrial machinery, machine tools, and machinery for ships. Then the reliability of hose assemblies is important because total hydraulic system, which used to deliver the fluid power ($P^*Q$) needed to flexibility in the piping system, is not operated if the hose assembly failed in the system. The data of the accelerated life test estimated through the shape parameter(${\beta}$) resulting of the Weibull distribution analysis. This study has tried to reduce the test time resulting from varying impulse pressure range and the flexing diameter. Accelerated life test model for the test results was adopted the GLL(generalized log linear) and the accelerated indexes are identified as 6.64 for the pressure and 4.46 for flexing radius. Also, it found that shape parameter is 6.19, scale parameter(${\eta}$) is $1.035{\times}108$, which were adopted the pressure 35 MPa and the flexing diameter R100 mm in the used condition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.804-810
• /
• 2000

In this paper, an experimental identification method is presented to identify the bulge wave and extensional wave propagation speeds in the fluid-filled elastic hose. An fluid-filled hose is hanged vertically for straight position. The exciting device of piston type is developed to generate the bulge wave and extensional wave in the elastic hose. Hydrophones are arranged in the fluid-filled hose linearly to measure the wave pressure. The wave speeds are estimated using the wavenumber-frequency spectrum analysis technique.