• Journal of Drive and Control
• /
• v.21 no.2
• /
• pp.30-35
• /
• 2024

Domestic rice is more expensive than imported products, so it is necessary to reduce production costs to secure competitiveness. Low-density planting developed in Japan is a cultivation technology that reduces labor and production costs without yield loss. The area of low-density cultivation is continuously increasing. However, research on how rice transplanters adapt to low-density planting has not been conducted. Therefore, this study was carried out to determine the optimal working conditions of a rice transplanter for low-density planting. Three types of rice transplanters were used and treated based on 3 conveying distance levels. The number of picked seedlings, pick missing rate, the number of planted seedlings, and the mis-planted rate were investigated to evaluate planting accuracy according to the transfer distance to the seedling tray. The results showed that the number of planted seedlings was 4.31~4.95 EA with an L1 seedling tray transfer distance (horizontal 9 mm, vertical 8 mm), but the mis-planted rate was higher than in other conditions. At L2 (horizontal 9 mm, vertical 10 mm) and L3 (horizontal 11 mm, vertical 8 mm) transfer distance conditions, the number of planted seedlings were 4.89-5.68 EA and 4.69-5.66 EA, respectively, with a low mis-planted rate of less than 3%. The results showed that if the transfer distance is adjusted properly, a rice transplanter can be used for low-density planting with high planting accuracy.

• Structural Monitoring and Maintenance
• /
• v.5 no.1
• /
• pp.111-127
• /
• 2018

Horizontal displacement of high-rise building is an essential index for assessing the structural performance and safety. In this paper, a novel inclinometer-based method is proposed to address this issue and an algorithm based on three spline interpolation principle is presented to estimate the horizontal displacement of high-rise buildings. In this method, the whole structure is divided into different elements by different measured points. The story drift angle curve of each element is modeled as a three spline curve. The horizontal displacement can be estimated after integration of the story drift angle curve. A numerical example is designed to verify the proposed method and the result shows this method can effectively estimate the horizontal displacement with high accuracy. After that, this method is applied to a practical slender structure - Shanghai Tower. Nature frequencies identification and deformation monitoring are conducted from the signal of inclinometers. It is concluded that inclinometer-based technology can not only be used for spectrum analysis and modal identification, but also for monitoring deformation of the whole structure. This inclinometer-based technology provides a novel method for future structural health monitoring.

• Steel and Composite Structures
• /
• v.4 no.3
• /
• pp.189-209
• /
• 2004

The commonly used seismic design procedures to evaluate the maximum effect of both horizontal components of earthquakes, namely, the Square Root of the Sum of the Squares (SRSS) and the 30-percent (30%) combination rules, are re-evaluated. The maximum seismic responses of four three-dimensional moment resisting steel frames, in terms of the total base shear and the axial loads at interior, lateral and corner columns, are estimated as realistically as possible by simultaneously applying both horizontal components. Then, the abovementioned combination rules and others are evaluated. The numerical study indicates that both, the SRSS rule and the 30% combination method, may underestimate the combined effect. It is observed that the underestimation is more for the SRSS than for the 30% rule. In addition, the underestimation is more for inelastic analysis than for elastic analysis. The underestimation cannot be correlated with the height of the frames or the predominant period of the earthquakes. A basic probabilistic study is performed in order to estimate the accuracy of the 30% rule in the evaluation of the combined effect. Based on the results obtained in this study, it is concluded that the design requirements for the combined effect of the horizontal components, as outlined in some code-specified seismic design procedures, need to be modified. New combination ways are suggested.

• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.4
• /
• pp.295-305
• /
• 2018

Network RTK is a highly practical technology that can provide high positioning accuracy at levels between cm~dm regardless of user location in the network by extending the available range of RTK using reference station network. In particular, unlike other carrier-based positioning techniques such as PPP, users are able to acquire high-accuracy positions within a short initialization time of a few or tens of seconds, which increases its value as a future navigation system. However, corrections must be continuously received to maintain a high level of positioning accuracy, and when a time delay of more than 30 seconds occurs, the accuracy may be reduced to the code-based positioning level of meters. In case of SSR, which is currently in the process of standardization for PPP service, the corrections by each error source are transmitted in different transmission intervals, and the rate of change of each correction is transmitted together to compensate the time delay. Using these features of SSR correction is expected to reduce the performance degradation even if users do not receive the network RTK corrections for more than 30 seconds. In this paper, the simulation data were generated from 5 domestic reference stations in Gunwi, Yeongdoek, Daegu, Gimcheon, and Yecheon, and the network RTK and SSR corrections were generated for the corresponding data and applied to the simulation data from Cheongsong reference station, assumed as the user. As a result of the experiment assuming 30 seconds of missing data, the positioning performance compensating for time delay by SSR was analyzed to be horizontal RMS (about 5 cm) and vertical RMS (about 8 cm), and the 95% error was 8.7 cm horizontal and 1cm vertical. This is a significant amount when compared to the horizontal and vertical RMS of 0.3 cm and 0.6 cm, respectively, for Network RTK without time delay for the same data, but is considerably smaller compared to the 0.5 ~ 1 m accuracy level of DGPS or SBAS. Therefore, maintaining Network RTK mode using SSR rather than switching to code-based DGPS or SBAS mode due to failure to receive the network RTK corrections for 30 seconds is considered to be favorable in terms of maintaining position accuracy and recovering performance by quickly resolving the integer ambiguity when the communication channel is recovered.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.8
• /
• pp.45-51
• /
• 2013

In the construction site of underground buildings which have severe environment such as dust, noise, vibration, the technology of rescue the builders in the construction site when accident occurs by tracking the location of the builders and express the mission of supervisor smoothly. In this study, in order to acquire the location information of the builders in the construction site of underground buildings by using MEMS INS and air pressure sensor, we firstly performed the field test in construction site, analyzed the location and the elevation accuracy based on the detected results, and then verified its practicality and rationality after all. As a result, we could acquire worker's position-accuracy within 10m in horizontal direction and 4m in vertical direction. Therefore we could judge availability in construction fields of underground structure.

• Journal of Korean Society for Geospatial Information Science
• /
• v.14 no.4 s.38
• /
• pp.11-18
• /
• 2006

In this paper, airborne LiDAR data were evaluated in horizontal and vertical accuracy. By using zigzag scanning type of LiDAR, GCPs are not tested directly. So points around GCPs were used in this evaluation. Building corner points were made from LiDAR's building planar and compared with ground surveyed GCPs, in horizontal accuracy test. Its accuracy shows 19cm average and 21cm RMSE and 15 points were within 20cm among 16 points. In vertical accuracy test, 41 GCPs were used and it shows 11cm average and 14cm RMSE and 75% of GCPs were within 15cm. This could be a criterion in topographic map modification and basic geographic DB and 3D data construction using airborne LiDAR data.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2007.04a
• /
• pp.231-235
• /
• 2007

As the centralization of city, underground facilities is increasing and being more important. And there were many underground facilities accidents in korea. It is very important to update and to have high quality accuracy of underground facilities maps. But the underground facilities maps are mapped and updated by each institutes. So it is difficult to verify the accuracy of the data. In this study, To analyze the accuracy of maps, Surveying of undergroud facilities for 18 GUs in Seoul is performed during 3 years using Electromegnetic Induction Method, Total Station and GPS. In conclusion, Horizontal accuracy of 6 underground facilities management institutes is 73cm(2004), 78cm(2005) and 75cm(2006).

• Korean Journal of Geomatics
• /
• v.2 no.2
• /
• pp.99-105
• /
• 2002

The accuracy of the Digital Photologging System, designed for the construction of the road Facility Database, highly depends on the positions and attitudes of the cameras from GPS/INS integration. In this paper, the development of a loosely coupled GPS/INS is presented. The performance of the system is verified through a simulation as well as a real test data processing. Since the IMU used in this study shows large systematic errors, the possible accuracy of the positions and attitudes of this low-performance IMU when combined with precise GPS positions are assigned. Currently, the integrated system shows the positional accuracy better than 5cm in real data processing. Although the accuracy of attitude based on real test could not be assigned at this time, it is expected that better than 0.5 degrees and 1.8 degrees for horizontal and down component are achievable according to the simulation result.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.4
• /
• pp.105-112
• /
• 1984

In horizontal positioning, various methods of adjustment have been studied and developed to improve accuracy. This paper aims to present the best effective adjustment in horizontal positioning. In this study, by observation of lengths and angles, Quadrilaterals and center-point pentagon are formed and analysed with Triangulation, Trilateration and combined method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.120-123
• /
• 2001

The semi-solid casting will have a higher internal integrity, mechanical properties and dimensional accuracy than the conventional castings. This process can reduce the manufacturing costs and finished weight for critical components. The semi-solid casting are capable of greater dimensional repeatbility, this supplies considerable savings when extensive machining, salvage and scrap are key variables in the current automotive product. One of the most important factor regarding the semi-solid die casting process are the reheating method of the raw materials to the semi-solid state. Therefore, in this present work, the horizontal type induction heating system to obtain the optimal reheating conditions suitable for semi-solid die casting process was designed and manufactured. And the microstructure of reheated materials was investigated.