• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.4
• /
• pp.171-179
• /
• 2018

Copper powder dispersed with 4 vol.% of $Cr_2O_3$ was successfully produced by a simple milling at 210 K with a mixture of $Cu_2O$, Cu and Cr elemental powders, followed by Hot Pressing (HP) at 1123 K and 50 MPa for 2h to consolidate the milled powder. The microstructure of the HPed material was characterized by standard metallographic techniques such as XRD (X-ray Diffraction), TEM and STEM-EDS. The results of STEMEDS analysis showed that the HPed materials comprised a mixture of nanocrystalline Cu matrix and $Cr_2O_3$ dispersoid with a homogeneous bimodal size distribution. The mechanical properties of the HPed materials were characterized by micro Vickers hardness test at room temperature. The thermodynamic considerations on the heat of formation, the incubation time to ignite MSR (Mechanically induced Self-sustaining Reaction), and the adiabatic temperature for the heat of displacement reaction between the oxide-metal are made for the delayed formation of $Cr_2O_3$ dispersoid in terms of MSR suppression. The results of TEM observation and hardness test indicated that the relatively large dispersoids in the HPed materials are attributed to the significant coarsening for the high temperature consolidation; this leads to the low Vickers hardness value. Based on the thermodynamic calculation for the operating processes with a limited number of parameters, the formation kinetics and coarsening of the $Cr_2O_3$ dispersoid are discussed.

• Solar Energy
• /
• v.15 no.2
• /
• pp.91-99
• /
• 1995

The influence of deposition parameters on the deposition of $SnO_2$ thin films by spray pyrolysis has been studied. In the case of spray solution with tile concentration of 0.01M, at low deposition temperature the deposition was controlled by surface reaction and portion controlled by mass transfer is increased with increasing deposition temperature to $400^{\circ}C$. Above $400^{\circ}C$, the deposition is controlled by mass transfer at low spray pressure, and by surface reaction at high spray pressure. As the concentration of spray solution increased the deposition rate increased, and in this experiment the deposition depends on the Rideal-Eley mechanism. The deposition rate increased with increasing substrate temperature up to $400^{\circ}C$ and then decreased due to homogeneous nucleation. The thickness of the deposit increased with increasing spray duration, and the adhesion between substrate and deposit was formed physically.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.358-364
• /
• 2018

An isotropic pitch precursor for fabricating carbon fibres was prepared by co-carbonization of ethylene bottom oil(EBO) and polyvinyl chloride (PVC). Various pre-treatments of EBO and PVC, and a high heating rate of $3^{\circ}C/min$ with no holding time, were evaluated for their effects on the oxidative stabilization process and the mechanical stability of the resulting fibres. Our stabilization process enhanced the volatilization, oxidative reaction and decomposition properties of the precursor pitch, while the addition of PVC both decreased the onset time and accelerated the oxidative reaction. Aliphatic carbon groups played a critical role in stabilization. Microstructural characterization indicated that these were first oxidised to carbon-oxygen single bonds and then converted to carbon-oxygen double bonds. Due to the higher heating rate and lack of a holding step during processing,the resulting thermoplastic fibers did not completely convert to thermoset materials, allowing partially melted, adjacent fibres to fuse. Fiber surfaces were smooth and homogeneous. Of the various methods evaluated herein, carbon fibers derived from pressure-treated EBO and PVC exhibited the highest tensile strength. This work shows that enhancing the naphthenic component of a pitch precursor through the co-carbonization of pre-treated EBO with PVC improves the oxidative properties of the resulting carbon fibers.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1097-1103
• /
• 2001

TiO$_2$anchored on a porous clay ceramic support (PCS) for use in lightweight photocatalyst were synthesized by the dropping precipitant method. A PCS of macro and micro pore size of around several mm~${\mu}{\textrm}{m}$ in diameter were prepared by the rapid heat treatment at, 1,15$0^{\circ}C$ for 10 min from low grade of clay. The change in pH of reaction solution due to the different addition rate of NH$_4$HCO$_3$as a precipitant, the reaction temperature and the concentration of TiCl$_4$had a pronounced effect on the nature of precipitated TiO$_2$particles on the surface of a PCS and the crystal structure of precipitated TiO$_2$particles. At an addition rate of 0.8 ml/min of NH$_4$HCO$_3$and pH=6 of reaction solution, homogeneous precipitation of TiO$_2$particles on a PCS was achieved. TiO$_2$particles with anatase phase was precipitated on the surface of a PCS at the low concentration of TiCl$_4$, the high addition rate of NH$_4$HCO$_3$and the high reaction temperature.

• Journal of the Korean Ceramic Society
• /
• v.36 no.4
• /
• pp.343-353
• /
• 1999

Microwave(2.45 GHz) was used as energy source in hydrothermal reaction to fabricate ultrafine BaTiO3 powder. Using microwave of 700 W, crytal BaTiO3 began to fom after 5 min in microwave-autoclave sys-tem. The crystallinity was not noticeably increased with increasing longer reaction time than 10 min. On the other hand in microwave-reflux system crytal BaTiO3 began to form after 15min and the crystallinity was not noticeably increased with increasing longer reaction time than 1hr,. In either case particle size dis-tribution was considerably uniform due to the effect of homogeneous heating by microwave. In addition mi-crowave heating gave an extremely small degree of particle agglomeration compared to electric heating. Av-erage sizes of as-synthesized powders were 30-60nm. Ba/Ti ratio in sol played an important role in det-ermining the particle size. It seems that excess barium forms different phases such as Ba(OH)2 which makes thin layer on the surface of BaTiO3 powder. This thin layer would inhibit the agglomeration of Ba-TiO3 powders and keep the small grain size. In microwave-autoclave system tetragonal-BaTiO3 was formed directly by the reaction of only 15 min. In the case of microwave-reflux system tetragonal-BaTiO3 was formed by driyng over 25$0^{\circ}C$.

• Journal of Microbiology and Biotechnology
• /
• v.6 no.2
• /
• pp.86-91
• /
• 1996

Thermostable $\beta$-mannanase from Bacillus sp. YA-14 was purified by acetone precipitation, CM-cellulose, Sephadex G-100 and hydroxyapatite column chromatography from culture supernatant. The final enzyme preparation appeared to be homogeneous on sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). $\beta$-Mannanase appeared to be a monomeric protein with a molecular weight of 67, 000 daltons. The optimal pH and temperature of the enzyme reaction were pH 6.0 and $75^{\circ}C$ , respectively. The enzyme was stable at a pH range of 6.0 to 9.0 and at temperatures between 45 and $85^{\circ}C$. The kinetic constants of $\beta$-mannanase as determined with a galactomannan (locust bean) as substrate were a Vmax of 25 unit/ml and a Km of 1.1 mg/ml. The enzyme had only limited activity on galactomannan substrate. It was suggested that mg $\beta$-mannanase activity is limited by the number of branched $\alpha$-galactose residues.

• Journal of the Optical Society of Korea
• /
• v.10 no.3
• /
• pp.130-142
• /
• 2006

Lab-on-a-chip technology is attracting great interest because the miniaturization of reaction systems offers practical advantages over classical bench-top chemical systems. Rapid mixing of the fluids flowing through a microchannel is very important for various applications of microfluidic systems. In addition, highly sensitive on-chip detection techniques are essential for the in situ monitoring of chemical reactions because the detection volume in a channel is extremely small. Recently, a confocal surface enhanced Raman spectroscopic (SERS) technique, for the highly sensitive biological analysis in a microfluidic sensor, has been developed in our research group. Here, a highly precise quantitative measurement can be obtained if continuous flow and homogeneous mixing condition between analytes and silver nano-colloids are maintained. Recently, we also reported a new analytical method of DNA hybridization involving a PDMS microfluidic sensor using fluorescence energy transfer (FRET). This method overcomes many of the drawbacks of microarray chips, such as long hybridization times and inconvenient immobilization procedures. In this paper, our recent applications of the confocal Raman/fluorescence microscopic technology to a highly sensitive lab-on-a-chip detection will be reviewed.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.5-7
• /
• 2014

A skeletal mechanism of coal combustion was derived from a detailed coal combustion kinetic mechanism through an importance analysis of chemical pathways. The reduction process consists of roughly two parts. The first process is performed based on a connectivity analysis between species. In this process, DRGEPSA is chosen for reduction process. Strongly connected species and related reactions from the important species set as start species by the operator are sorted into the reduced mechanism. About 70% of species and reactions can be removed with a limited accuracy loss. Subsequently the second reduction process, CSP, is performed. This method focuses on an importance of each reaction and can reduce a volume of mechanism appropriately. Through these analyses, a skeletal mechanism is generated that is including 65 species and 150 reactions. The generated skeletal mechanism is verified through a comparison with the detailed mechanism in the homogeneous reactor model of CHEMKIN-PRO under wide range of conditions. The generated mechanism can give an advantage in the analysis of coal combustion characteristics in detail in large scale simulations such as LES and DNS.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.2
• /
• pp.73-79
• /
• 2002

The polyol process which applies to cobalt, nickel. copper and precious metals is a interesting and unexpected example of such a method for preparing uniform metal powders. The reaction proceeds via dissolution, and the polyol acts simultaneously as a solvent, a reducing agent, and to some extent a protective agent. Submicrometer uniform cobalt particles can be obtained by seeding the reactive medium ($AgNO_3$) to achieve a complete substitution of homogeneous by heterogeneous nucleation. By varying the number of nuclei it is possible to control to some extent the average particle size in the submicrometer (0.5$\mu$m) range.

• BMB Reports
• /
• v.31 no.4
• /
• pp.345-349
• /
• 1998

Aspartase (EC 4.3.1.1) from Hafnia alvei was purified to homogeneity by a combination of DEAE-cellulose, Red A-agarose, and Sepharose 6B chromatography. The purified enzyme appeared homogeneous on denatured SDS-polyacrylamide gel electrophoresis. The purified enzyme was a tetrameric protein composed of identical subunits with a molecular weight of 55,000 daltons. The optimum pH for the enzymatic reaction was 8.5 and the optimum temperature for maximum activity was $45^{\circ}C$. The enzyme has an absolute requirement of divalent metal ions ($Mg^{2+}$, $Mn^{2+}$) at the alkaline pH. The enzyme, however, was inactivated in the presence of other divalent cations such as $Zn^{2+}$, $Ca^{2+}$. The helical content of the purified enzyme was estimated by CD spectropolarimetry to be 61%.