• 대한기계학회논문집B
• /
• 제33권9호
• /
• pp.722-727
• /
• 2009

The effect of the intake flow on the spray structure of a high pressure 11-hole fuel injector were examined in a single cylinder optical direct injection spark ignition (DISI) engine. The effects of injection timing and in-cylinder charge motion were investigated using the 2-dimensional Mie scattering technique. It was confirmed that in the homogeneous charge mode, the in-cylinder swirl charge motion played a major role in the fuel spray distribution during the induction stroke rather than the tumble flow. But, in the stratified charge mode, the effect of the in-cylinder charge was not so large that the injected spray pattern was nearly maintained and the increase of in-cylinder pressure by the upward moving piston reduced the fuel spray penetration.

• 한국인쇄학회지
• /
• 제24권1호
• /
• pp.35-44
• /
• 2006

본 연구에서는 PCB에 진공인쇄 방식이 적용된 스크린 인쇄방법을 이용하여 Pattern 및 Hole충전의 신뢰성을 향상시킬 수 있는 기술을 적용하였다. 새로운 dry process 기술인 직접회로 인쇄 기술은 일반적으로 사용되고 있는 wet process 중 도금, 에칭, 박리 등의 공정을 줄일 수 있어 제조원가, 공정 리드타임 감소, 폐기물 감소로 환경 친화적 공정이라고 할 수 있다. 직접회로 인쇄는 진공도 100 Pa, 인쇄압력 0.45 MPa, 인쇄 속도 30 mm/sec, 인쇄각도 85도, 스크린 마스크와 기판 사이의 Gap 2 mm에서 인쇄될 때 가장 좋은 결과를 보였다. 직접회로 인쇄에 사용된 인쇄기는 일반 PCB공정에서 사용되는 동일한 형태에 진공조건을 유지시킬 수 있도록 개선하여 사용하였다.

• 환경영향평가
• /
• 제20권3호
• /
• pp.381-395
• /
• 2011

Present work aims to establish an integrated management system of environmental data base for nine typical wind holes or air holes in Korea. It basically deals with definition, geographical distribution, morphological pattern, physical characteristics and anthropogenic environments of wind hole to propose systematic preservation strategy of their periglacial landscape and flora, which are known to be sensitive to global warming. Wind hole, in which cool air blows out during the summer, but mild air comes out during the winter from a cave or hole, is frequently found on northwest- and north-facing slopes on the terminal point of steep talus, block field, and block stream, and can be categorized into three types, i.e., talus, cave and sink types. Environmental characteristics of nine wind holes are analyzed on the basis of their geology, landform, climate, soil, hydrology, vegetation, road, footpath, land-use, and management system, and relevant DB are prepared. Wind hole areas with unique landscape and ecological values need to be designated as a nature reserve, and zoning of core, buffer, and transitional zones are required for the multi-dimensional preservation of periglacial landscape and ecosystem. Phytogeographical values of glacial relict plants, including mountain cranberry(Vaccinium vitis-idaea) at its global southernmost limit at Bangnaeri wind hole, Hongchon County, Gangwon Province of Korea are discussed in detail as a floristic refugia in connection with climate change during the Pleistocene Epoch and potential in-situ and ex-situ preservation sites in the future.

• 한국정보전자통신기술학회논문지
• /
• 제13권6호
• /
• pp.568-574
• /
• 2020

본 논문에서는 영상처리에 사용되는 Canny edge 검출 알고리즘 중 가장 높은 연산 복잡도를 가진 제곱근 연산 횟수를 감소시키는 방법을 제안한다. 제안하는 방법은 기울기 벡터 연산 과정에 사용되는 제곱근 연산을 이용할 때 일부 픽셀에 특정한 규칙을 사용해 홀을 만들어 제곱근 연산을 직접 하지 않고 주변 픽셀들의 연속성을 이용하여 기울기 벡터를 계산하여 연산 횟수를 감소시킨다. 다양한 테스트 이미지를 이용해 실험한 결과 홀이 1개인 경우 약 97%, 홀을 증가시키면 각각 약 94%, 90%, 88%의 일치율을 보였고, 홀이 1개인 경우에는 0.2ms의 연산시간이 감소되었고, 홀을 증가시키면 각각 약 0.398ms 0.6ms, 0.8ms의 연산시간이 감소되었다. 이를 바탕으로 hole이 2개인 경우 높은 정확도와 연산 수 절감을 통해 저전력 임베디드 비전 시스템을 구현할 수 있을 것으로 기대한다.

• 한국기계가공학회지
• /
• 제12권2호
• /
• pp.75-80
• /
• 2013

Cathode is an essential component used in plasma etching process which is to make micro pattern on the silicon wafer. The currently used cathodes produce particles at the high temperature plasma etching process. To overcome this problem, a 'Silicon Only Cathode' was developed. This 'Silicon Only Cathode' requires manufacturing process changes due to the change of shapes, material features, and machining characteristics of work materials. This research investigates the small hole drilling process. The conclusion is that PCD drills with twist angles of $20^{\circ}$ and $25^{\circ}$ were tested for small hole drilling and the experimental results indicate that the drill with $25^{\circ}$ twist angle drill causes less thrust force.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1638-1640
• /
• 2003

In the recent years, UHF PD measuring technique for detecting partial discharges was proved the effective method for Gas Insulated Switchgear (GIS). However, in case of GIS with a metal flange around insulating spacer, UHF PD measurement using typical external UHF PD sensor is difficult. In this paper, a novel hole-type UHF PD sensor based on Archimedean spiral antenna theory has been proposed and realized. All spacers with metal flange have small hole in order to inject epoxy. Using the novel hole-type UHF PD sensor, it makes detection possible to PD signal that are emitted through the epoxy injection hole. Additionally, the measuring characteristic of UHF PD signals from several artificial defects in GIS and the novel ${\Phi}$-f-q pattern analysis technology are discussed.

• Journal of Welding and Joining
• /
• 제16권3호
• /
• pp.64-73
• /
• 1998

This paper is concerned with defects detection and evaluation of heat affected zone (HAZ) in austenitic stainless steel type 304 by ultrasonic wave and neural network. In experiment, the reflected ultrasonic defect signals from artificial defects (side hole, vertical hole, notch) of HAZ appears as beam distance of prove-defect, distance of probe-surface, depth of defect-surface on CRT. For defect classification simulation, neural network system was organized using total results of ultrasonic experiment. The organized neural network system was learned with the accuracy of 99%. Also it could be classified with the accuracy of 80% in side hole, and 100% in vertical hole, 90% in notch about ultrasonic pattern recognition. Simulation results of neural network agree fairly well with results of ultrasonic experiment. Thus were think that the constructed system (ultrasonic wave - neural network) in this work is useful for defects dection and classification such as holes and notches in HAZ of austenitic stainless steel 304.

• 한국안전학회지
• /
• 제2권3호
• /
• pp.37-43
• /
• 1987

The combustion process in gas turbine combustor mainly influenced by flow pattern in combustor, and especially the flow pattern near the nozzle and the shape of recirculation zone affect strongly on the flame stabilization, temperature distribution and combustion efficiency in combustor. In this paper, the author has designed and manufactured transparent simplified model combustors on the basis of K. Suzuki's combustor design method to investigate the effects of swirl number and secondary air hold arrays in axial position on the flow characteristics by adopting the tuft method and 5 hole pitot tube.

• 대한기계학회논문집A
• /
• 제27권5호
• /
• pp.772-778
• /
• 2003

Polystyrene foam is easily melted and vapoured by heat, has a proper quality in the pattern manufacturing and has a low price. The objective of this study is to develop a rapid prototyping method fur polystyrene foam pattern manufacuring to use the eliminative pattern casting (EPC). Applying fur the rapid prototyping concept reversely, the unnecessary part of section is vapored away by heat source of laser beam. In order to examine the applicability between laser beam process and polystyrene foam material, the basic experiments such as hole, line, plane and contour process are carried out. With these results, various three-dimensional shape patterns are made and this rapid prototyping tool for polystyrene foam manufacturing.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.451-454
• /
• 2007

This paper presents the pattern characteristic using the electrostatic drop-on-demand ink-jet printing system. In order to achieve the pattern characteristic of electrostatic inkjet printing, the capillary inkjet head system is fabricated using capillary tube, Pt wire and electrode, and is packaged by acrylic board for the accurate alignment between wire and electrode-hole. The applied DC voltage of 1.4 $\sim$ 2.0 kV used for the observation of electrostatic droplet ejection. Electrostatic droplet ejection is directly observed using a high-speed camera. For investigated pattern characteristic, conductive inkjet silver ink used. The higher voltage has a good condition which has micro dripping mode. Also, the droplet size decreases with increasing the supplied DC voltage. This paper shows the pattern which is formed by about 300um. Also, capillary inkjet head system will be applied industrial area comparing conventional electrostatic inkjet head system.