• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.4
• /
• pp.271-277
• /
• 1998

Nondestructive method can include both testing itself and analysis or evaluation of the testing results. Although vast amount of testing can be accomplished in a fairly short amount of time due to the advancement of electronic technology. it is really difficult matter to identify whether the indication found during testing corresponds to be a real defect. Thus, in ultrasonic testing, advanced digital signal processing techniques have been widely studied in order to identify the shape of the defect during testing, and one of the signal processing techniques, synthetic aperture focusing technique(SAFT) was tried for holes machined in carbon steel plate in this study. Result showed that signal to noise ratio has been improved considerably compared to the result from original RF signals.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.44-50
• /
• 1999

For the prediction of combustion performance of the Unlike Impinging Quadlet Injector (OOOF type), mixing efficiency, mixing characteristic velocity, and efficiency of mixing characteristic velocity were obtained from the cold test. Water/kerosene were used for simulants, The momentum ratio of oxidizer and fuel were mixing correlating parameter. Orifice discharge coefficient, spray pattern and mass distribution were measured. As a result, invasion-depth had strong effect on mixing efficiency, mixing characteristic velocity, and efficiency of mixing characteristic velocity. Mixing efficiency and efficiency of mixing characteristic velocity showed maximum value for momentum ratio 1.67(TMR = 2.5), and fuel rich state showed larger decreasing ratio than oxidizer rich state.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.4
• /
• pp.382-388
• /
• 2010

In this work the replacement material for magnesium alloy was investigated and an optimized design was suggested for the horizontal fin of a fighter's external fuel tank. For the replacement of magnesium alloy, Aluminum alloy, AL 2034-T351, was selected by considering material properties and its procurement. The strength and fracture toughness properties of AL 2034-T351 are stronger than those of magnesium alloy, but the specific weight of AL 2034-T351 is heavier than that of magnesium alloy by 65%. To meet the allowable limit of C.G. shift in the tank, the design of horizontal fin was optimized by reducing the original shape by 20% and resizing the maximum thickness to 7 mm. From the results of the static and dynamic stress analysis for improving the safety factor of the joint section and the joint hole, the radius of curvature in the aft joint section of the new fin was designed as 8.5mm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.150-150
• /
• 2008

본 연구에서는 Wet chemistry damage가 Nanopatterned p-ohmic electrode에 미치는 영향을 연구하였다. Nanopattern은 Metal clustering을 이용하여, P-GaN와 Ohmic형성에 유리한 Pd을 50$\AA$ 적층한 후 Rapid Thermal Annealing방법으로 $850^{\circ}C$, $N_2$분위기에서 3min열처리를 하여 Pd Clustering mask 를 제작하였다. Wet etching은 $85^{\circ}C$, $H_3PO_4$조건에서 시간에 따라 Sample을 Dipping하는 방법으로 시행하였다 Ohmic test를 위해서 Circular - Transmission line Model 방법을 이용하였으며, Atomic Force Microscopy과 Parameter Analyzer로 Nanopatterned GaN surface위에 형성된 Ni/ Au Contact에서의 전기적 분석과, 표면구조분석을 시행하였다. AFM결과 Wet처리시간에 따라서 Etching형상 및 Etch rate이 영향을 받는 것이 확인되었고, Ohmic test에서 Wet chemistry처리에 의한 Tunneling parameter와 Schottky Barrier Height가 크게 증/감함을 관찰하였다. 이러한 결과들은 Wet처리에 의해서 발생된 Defect가 GaN의 표면과 하부에서 발생되며, Deep acceptor trap 및 transfer거동과 밀접한 관련이 있음을 확인 할 수 있었다. 보다 자세한 Transport 및 Wet chemical처리영향에 관한 형성 Mechanism은 후에 I-V-T, I-V, C-V, AFM결과 들을 활용하여 발표할 예정이다.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.385-388
• /
• 2002

The researches of a two-phase atomizers have been carried out in the field of automotive and aerospace industries in order to improve the atomization performance of the liquid droplets ejecting from these nozzles. The smaller droplets have the advantages of the reduction of environmental pollution matter and effective use of energy through the improvement of heat and mass transfer efficiency. Thus, to propose the basic information of two-phase flow, an internal mixing atomizer was designed, its shape factor was 0.6 and the liquid feeding hole was positioned at the center of the mixing tube which was used to mix the air and liquid. The experimental work was performed in the field after the nozzle exit orifice. The measurement of the liquid droplets was made by PDPA system. This system can measure the velocity and size of the droplets simultaneously. The number of the droplets used in this calculation was set to 10,000. The flow patterns were regulated by ALR (Air to Liquid mass Ratio). ALR was varied from 0.1024 to 0.3238 depending on the mass flow rate of the air. The analysis of sampling data was mainly focused on the spray characteristics such as flow characteristics distributions, half-width of spray, RMS, and turbulent kinetic energy with ALR.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.109-117
• /
• 2002

An off-surface flow visualization experiments have been performed to investigate the flow field over a delta wing with the leading edge extension(LEX). The model is a flat wing with $65^{\circ}$ sweepback angle. The free stream velocity is 6.2 m/s, which corresponds to Reynolds number of $4.4\times10^5$ based on the wing root chord. The angle of attack and sideslip angle range from $16^{\circ}\sim28^{\circ}$ and $0^{\circ}\sim-15^{\circ}$, respectively. The visualization technique of using the micro water-droplet and the laser beam sheet enabled to observe the vortical flow structures, which can not be obtained by 5-hole probe measurements. With sideslip angle, the interaction and breakdown of the LEX and wing vortices was promoted in the windward side, whereas, it was suppressed in the leeward side.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.499-500
• /
• 2006

The electrode wear in micro-EDM significantly deteriorates the machining accuracy. In this regard, electrode wear needs to be compensated in-process to improve the product quality. Therefore, there are substantial amount of research about electrode wear. In this study a control method for micro-EDM using discharge pulse counting is proposed. The method is based on the assumption that the removed workpiece volume is proportional to the number of discharge pulses, which is verified from experimental results analyzing geometrically machined volume according to various number of discharges. Especially, the method has an advantage that electrode wear does not need to be concerned. The proposed method is implemented to an actual micro-EDM system using high speed data acquisition board, simple counting algorithm with 3 axis motion system. As a result, it is demonstrated that the volume of hole machined by EDM drilling can be accurately estimated using the number of discharge pulses. In EDM milling process a micro groove without depth variation caused by electrode wear could be machined using the developed control method. Consequently, it is shown that machining accuracy in drilling and milling processes can be improved by using process control based on the number of discharge pulses.

• Horticultural Science & Technology
• /
• v.18 no.6
• /
• pp.787-791
• /
• 2000

Lettuce seedlings used in this investigation of planting distance and labor-saving efficiency were first grown in 100-hole paper trays for 30 days. Seedling height for transplanting ranged from 3 cm to 6 cm and plants had 3 to 5 leaves. The beds prepared for transplanting were of the arched type and were 35-40 cm in width, 15-20 cm in bed height, and between-bed furrow width was 20 30 cm. Typical seedling planting depth with the transplanter was 4-5 cm, although depth was quite variable because of the irregularities of the ground. Total transplanting time with the transplanter varied from 2.6 to 2.7 hours per 10a, while it took 38.1 hours per 10a with conventional planting. It was critical that the condition of both the seedlings and the bed be adjusted to the transplanter before planting. Considering yield and inter-plant distance, optimal transplanter performance resulted with $60{\times}20cm$ or $60{\times}25cm$spacing, and the labor-saving efficiency using the transplanter was improved by over 93% of that of conventional planting by hand.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.2
• /
• pp.93-102
• /
• 1995

A series of test was performed by measuring the failure strength and the failure mode of fiber reinforced composite laminates joint containing two holes in Series or Parallel. $[0^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}]_s$ laminate with W/d(Side distance ratio) 4.0 and E/d(Edge distance ratio) 3.0 has the full bearing strength and are preferable in case of the good efficiency in two series hole. Comparisons were made between testing results and predicting values of the FEM model. Good agreements were fecund between them except the case of $E/d=2{\sim}3$. In the case of $G_h{\geq}3.0d$ and $G_v{\geq}3.0d$ since the interaction coefficients between two parallel holes and between two series holes were small, holes can be treated as independent. The Acoustic Emission(AE) and SEM method were utilized to find out the initial defects, damage and the fracture mechanism.

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.32.5-33
• /
• 2009

카네기 천문대에서 주도하여 개발 중인 구경 25.4m GMT 망원경 사업에 한국도 공식적으로 참여하였다. 현재 한국천문연구원은 GMT(Giant Magellan Telescope)부경부를 국내에서 개발하고자 이와 관련된 연구를 진행하고 있다. GMT 부경은 직경 1.06m 오목거울 7장이 모여 전체 직경 3.2m인 타원면을 형성하고 초점비는 F/0.7이다. GMT 부경개발 선행 연구과제로 카네기 천문대에서 개발되어 현재 운용중인 구경 6.5m 마젤란 망원경의 부경을 선택하였는데, 이는 마젤란 부경의 형상과 직경, 부경시스템 운영방식이 GMT 와 유사하기 때문이다. 천체관측 망원경에서 거울면의 변형에 가장 큰 영향을 미치는 인자는 거울의 자중이다. 거울의 직경이 커지면 자중이 증가하게 되어 거울면의 처짐이 커지게 된다. 이를 극복하고자 다양한 거울 support들이 개발되었다. 그중에서 counterweight lever 시스템 같은 부양(float) 시스템은 자중의 영향을 보상해 줌으로써 그것에 의한 거울의 변형을 최소화하는 역할을 하는데, GMT 부경 개발에 근간이 되는 마젤란 부경 또한 부양 시스템을 도입하였다. 마젤란 부경의 부양시스템은 counterweight lever 시스템과 유사한 진공 시스템을 도입하였다. 마젤란 부경의 support는 axial 방향으로 거울을 지지하는 axial support와 lateral 방향으로 거울을 지지하는 lateral support가 있는데, 이중에서 axial support가 진공시스템으로 구성된다. Lateral 방향의 지지는 경량화된 거울의 hole 안에 3개의 판스프링을 삽입하여 단지 거울과 판스링의 강성에 의해서만 이루어진다. 이 논문에서는 망원경이 작동을 할때 즉, 천정각(zenith angle)이 변할 때 axial support와 lateral support의 조합(combination)에 의해 지지되는 마젤란 부경의 표면 정밀도 RMS 값을 비교하였다.