• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.209-214
• /
• 1999

Strength provisions in Korea Concrete Institute code are more conservative that those in ACI code by increasing load factors and decreasing capacity reduction factors. Cement content of mix design in construction field is usually higher than the modified for standard deviation because of rigorous inspection. Higher cement content increases not only strengths but also heat of hydration, shrinkage and brittleness which are not beneficial. To reduce and optimize the cement content in current mix design of Korean Highway Corporation, properties of fresh and hardened concrete for 16 different mix proportions have been investigated. It is found that the chemical admixture and cement of current mix proportions for highway construction are somewhat higher than the optimum amount. Therefore, the optimum mix design for 16 different purposes has been proposed.

• 자동차안전학회지
• /
• 제6권2호
• /
• pp.23-28
• /
• 2014

Commercial vehicle ESC assessment for curvature road was conducted. The previous study of ESC activation condition for losing controllability utilizing the test protocols of double lane change and sine with dwell method was conducted without considering the geometric complexity of roadway design. Since critical rollover accidents were frequently observed in the exit ramp zone, variety of curve, slope and bank have been added for analysis conditions. Detailed feature of the ramp including location, dimension and design characteristics have been analyzed from the typical trumpet type ramp design. Analyzing accident data from 2008, two specific ramps have been selected due to their complexity in design and severity in steering operation.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1316-1323
• /
• 2005

Most tunnel lining material which has been used in the domestic is a concrete. But many problems as the construction period, the cost, and the crack occurrence for the design, construction, and management were happened in the concrete lining. For this reason, many research institutes like the Korea Highway Corporation recognize the necessity of an alternate material development and grow on the interest for that. So in this study, the behaviour characteristics for the application of the Corrugated Steel Plate Lining in cut-and-cover tunnel are evaluated as several conditions for the backfill height, the cutting slope, and the relative density of backfill soil are changed. In addition, through using that conditions, CHBDC(2000, Canadian Highway Bridge Design Code) is evaluated if it could be applied to the design by comparing with the numerical analysis results. As the behaviour characteristics of the Corrugated Steel Plate Lining by CHBDC and the static numerical analysis are analyzed, both the methods show the same linear increases of the compressive stress according to the increase of the backfill height. The CHBDC of the dead load condition has very similar tendency by comparing with the result of the static numerical analysis.

• 대한교통학회지
• /
• 제23권3호
• /
• pp.73-84
• /
• 2005

도로기하구조 설계기준은 운전자의 안전성 향상과 원활한 주행능력을 제공할 수 있도록 마련되었으나 지형조건이 열악한 우리나라의 경우 부득이 설계기준이 의도하는 방향과 운전자가 인지하는 특성에 차이를 보임으로써 안전성에 문제점이 있는 경우가 많다. 이러한 교통사고의 위험성을 감소시키기 위한 대책 중에 하나로 도로안전시설물을 설치하지만 설치한 안전시설물에 대한 평가는 제대로 이루어지지 않고 있으며, 특히 도로환경적 요인과 인적요인과의 관련성에 대한 연구는 상당히 미흡한 실정이다. 본 연구에서는 도로 이용자들이 종단선형구간에서 느끼는 도로안전성 요인을 파악하기 위하여 차량시뮬레이터(Driving Simulator)와 3D 그래픽 화면으로 종단선형구간을 재현하고 도로안전시설물의 설치 유, 무에 따라 운전자가 느끼는 안전성의 변화와 도로 이미지를 조사하였다. 조사된 데이터를 바탕으로 수량화 제II류에 의한 정준상관분석을 실시하여 도로 안전성의 영향 요인을 분석하였으며 수량화제 I류에 의한 모형화를 실시하여 안전성을 예측한 결과 도로안전시설물과 운전자가 느끼는 안전성과의 관계를 명확히 규명할 수 있었다.

• Structural Engineering and Mechanics
• /
• 제77권3호
• /
• pp.343-354
• /
• 2021

The frequencies formulas of the bridge are of great importance in the design process since these formulas provide insight dynamic characteristics of the structure, which guides the designers to parametric analyses and the layout of the bridge in conceptual or preliminary design. Continuous rigid frame bridge is popular in the mountainous area. Mostly, this type of bridge was simplified either as a girder or cantilever when calculating the frequency, however, studies showed that the different configuration of the bridge made the problem more complex, and there is no unified fundamental calculation pattern for this kind of bridge. In this study, an empirical frequency equation is proposed as a function of pier's height, stiffness of pier and the weight of the structure. A unified fundamental frequency formula is presented based on the energy principle, then the typical continuous rigid frame bridge is investigated by finite element method (FEM) to study the dynamic characteristics of the structure, and then several key parameters are investigated on the effect of structural frequency. These parameters include the number, position and stiffness of the tie beam. Nonlinear regression analyses are conducted with a comprehensive statistical study from plenty of engineering structures. Finally, the proposed frequency equation is validated by field test results. The results show that the fundamental frequency of the continuous rigid frame bridge increases more than 15% when the tie beams are set, and it increases with the stiffness ratio of tie beam to pier. The results also show that the presented unified fundamental frequency has an error of 4.6% compared with the measured results. The investigation can predicate the approximate longitudinal fundamental frequency of continuous ridged frame bridge, which can provide reference for the seismic response and dynamic impact factor design of the pier.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 사면안정 학술발표회 논문집
• /
• pp.81-98
• /
• 1998

• 한국도로학회논문집
• /
• 제16권6호
• /
• pp.181-189
• /
• 2014

PURPOSES : Ambiguous decision on whether rural or urban area for road design can increase the construction cost and restrict the land use of surrounding area. However, administrative classification on rural and urban area is not directly related to road design because of this classification is not based on the engineering viewpoint, so method which can explain the road design context is required. METHODS : Method which enables to identify the area for road design is suggested based on the deceleration expected to be experienced by drivers who use the road section concerned. Deceleration rate corresponding to the area such as rural or urban suggested in Road Design Guideline is used as the criteria to identify the area by comparing this value with the estimated deceleration rate at the road section concerned. Speed profile method is utilized to derive the deceleration rate, and speed estimation way for reflecting both road geometry and intersection is suggested using stopping sight distance concept. RESULTS : The procedure of the method application is suggested, and the design example utilizing the method is provided. CONCLUSIONS : The method is expected to be used to identify the area for road design with engineering viewpoint, and design consistency among the roads with similar driving environment can be made.

• International Journal of Concrete Structures and Materials
• /
• 제7권4호
• /
• pp.319-332
• /
• 2013

The purpose of this study was to investigate the design comparison of totally prefabricated bridge substructure system. Prefabricated bridge substructure systems are a relatively new and versatile alternative in substructure design that can offer numerous benefits. The system can reduce the work load at a construction site and can result in shorter construction periods. The prefabricated bridge substructures are designed by the methods of Korea Highway Bridge Code (KHBD) and load and resistance factor design (AASHTO-LRFD). For the design, the KHBD with DB-24 and DL-24 live loads is used. This study evaluates the design method of KHBD (2005) and AASHTO-LRFD (2007) for totally prefabricated bridge substructure systems. The computer program, reinforced concrete analysis in higher evaluation system technology was used for the analysis of reinforced concrete structures. A bonded tendon element is used based on the finite element method, and can represent the interaction between the tendon and concrete of a prestressed concrete member. A joint element is used in order to predict the inelastic behaviors of segmental joints. This study documents the design comparison of totally prefabricated bridge substructure and presents conclusions and design recommendations based on the analytical findings.

• 한국도로학회논문집
• /
• 제10권2호
• /
• pp.57-67
• /
• 2008

현재 우리나라에서 도로 평면선형 설계를 위해 도로설계속도 개념을 사용하고 있다. 도로설계속도 개념은 단 한 개 도로 설계속도를 사용하기 때문에 도로 기하구조 수준이 일정해진다는 강점을 갖고 있으나, 도로 건설 후 그 도로를 주행하는 실제 차량 속도가 설계속도와 달리 나타날 수 있다는 약점을 갖고 있기도 하다. 본 연구에서는 이 약점을 보완하기 위해, 이미 여러 나라에서 사용 중인 주행속도 예측모형에 근거한 평면 선형설계기법을 제안한다. 본 연구에서는 이를 위해 우리나라 전역에서 표본을 선택하여 차량 속도조사를 수행했고, 속도에 영향을 미치는 도로설계요소를 통계분석을 통해 선정하여 양방향 2차로와 4차로 일반국도에 대한 차량 주행속도 모형을 제시했으며, 그 모형을 도로 평면선형설계에 적용하는 과정을 제시했다. 한편 새로운 기법에 대한 유효성을 밝히기 위한 실제 사례분석에서 새로운 기법은 기존 기법이 갖고 있는 약점을 해소하는 것으로 밝혀졌다. 향후 우리나라 도로 건설 사업에서 본 연구에서 제안한 평면선형 설계기법을 적용하면 도로 투자 효율성이 높아지고, 더 높은 설계일관성을 확보할 수 있을 것으로 판단한다.

• 한국도로학회논문집
• /
• 제13권2호
• /
• pp.167-174
• /
• 2011

본 연구는 특수 구간의 도로 포장에 포스트텐션 콘크리트 포장(PTCP: Post-Tensioned Concrete Pavement) 공법을 적용하기 위한 설계 방안을 제시하기 위하여 수행되었다. 본 연구에서 고려한 특수 구간으로는 기존의 포장에서 많은 문제점이 발생하는 도심지 버스전용차로 정류소 구간과 고속도로 암거 설치 구간을 선정하였다. 이러한 특수 구간의 PTCP 설계는 응력 기준 설계와 피로파손 기준 설계로 이루어지며 두 설계 결과 중에서 보수적인 결과를 설계에 적용한다. 응력 기준 설계에서는 유한요소해석을 통해 극한의 하중조건을 고려하여 발생할 수 있는 최대 인장응력을 산정한 뒤 이를 감소시켜서 최대 인장응력이 허용휨강도 이하가 되도록 텐던의 개수와 긴장 간격을 산정하였다. 피로파손 기준 설계에서는 AASHTO 피로파손 공식을 기반으로 긴장 설계를 수행하였다. 연구결과, 버스전용차로 정류소 구간과 암거 설치 구간에 PTCP 공법을 적용할 수 있는 설계 방안을 수립하였다.