• International Journal of Highway Engineering
• /
• v.17 no.5
• /
• pp.123-133
• /
• 2015

PURPOSES : This study aimed to develop a new highway capacity estimation method and provide comparative results among traditional capacity estimation methods and the recommended values in the latest version of KHCM. METHODS : The limitations of the existing methods, such as inconsistency and underestimation of the capacity value, are summarized through an extensive literature review. To overcome these limitations, a new method is introduced by adopting a definition of capacity and traffic flow characteristics at or near breakdown points. This method can produce the capacity value by searching a point corresponding to the maximum traffic flow through analysis of gradient changes (point of inflection) of the traffic flow and speed distribution. Comparative results of capacity values from each method are also presented to validate the new method by using data collected from detectors on freeways. RESULTS: From the analysis results, it is shown that a consistent capacity value can be estimated by applying the new method. In addition, the resulting capacity values are 3%-4% higher than those recommended in KHCM. CONCLUSIONS : The capacity values listed in the current KHCM tend to produce underestimated results. The new method presented in this paper may be included in the future edition of KHCM.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.123-134
• /
• 2015

PURPOSES : The key point of a multimodal LOS (level-of-service) evaluation system is that all of the modes are mutually associated to determine each mode's LOS. For example, the LOS of the bicycle mode is measured based on not only bicycle volumes, but also automobile volumes. However, the Korea Highway Capacity Manual (KHCM) still focuses on the automobile mode in evaluating the LOS of the roads. Additionally, the KHCM's LOS of the other modes, except for the automobile, is not consistent with actual road conditions. The KHCM, therefore, needs to develop and introduce a multimodal LOS system in order to evaluate the service conditions more accurately. METHODS: As a preliminary step to the introduction of multimodal LOS research, in this study the current problem of the KHCM's LOS system through a close review and comparison with other HCMs (highway capacity manuals) was identified. Secondly, a field survey and investigation of the urban streets to apply the HCM's multimodal LOS system was conducted. Finally, a comparison analysis of the results of the HCM and KHCM LOS was performed. RESULTS: In the study, it was found that the results of the LOS for the automobile mode did not show a significant difference between the HCM and KHCM. However, the LOS of the bicycle and pedestrian mode tended to be worse in the multimodal LOS system, which results from considering the effects of the automobile mode. Moreover, it was found that many cases have the potential to improve the overall LOS conditions, while reducing the automobile capacity. CONCLUSIONS: With the introduction of the multimodal LOS system, road diet and complete streets can be easily applied to ans actual road improvement project. Ultimately, the multimodal LOS system should be introduced into the KHCM, which can then be applied to traffic impact studies and other road improvement projects for more accurate evaluations.

• Journal of Korean Society of Transportation
• /
• v.13 no.1
• /
• pp.125-152
• /
• 1995

The purposes of this study are twofold ; (1) to investigate the accuracy of estimation power of the individual models. such as those of Highway Capacity Nanual (HCM), Korea Highway Capacity Manual (KHCM), and NationalCooperative Highway Research Program(NCHRP) Report339 ; and (2) to develop an adjusted delay model which can be applied to the signal control system in urban areas. The study is mainly focused on four subjects related to the research purposes, which are as follows ; (1) characteristecs of exsisting delay models ; (2) inherent problems in exsisting delay models : (3) validation of the proposed model by the comparison of observed delay with estimated delay :and (4) a method which can be applied to develop an appropriate delay model for actrual signal control systems by the adjusted fact of the proposed model.

• Journal of Korean Society of Transportation
• /
• v.13 no.1
• /
• pp.167-183
• /
• 1995

The objective of study is to evaluate highway capaicty estimation alternative and to develop capacity from statistical distribution of observed traffic flow. Speed-Volume relation is analyzed from vehicle's headway distribution eliminating the long headway by confidence intervals 99%, 95%, 90%. Capacity estimate alternatives were evaluated from 95% , 90%, 85% level of cummulative distribution of observed hourly traffic flow adjusted to confidence intervals. The result of investigation revealed that maximum hourly rate of flow is 2, 130pcu at confidence interval of 995, 2, 233pcu at 95%, 2, 315pcu at 90% respectively. Compared to the capacity of 2, 200pcu per hour per lane used in HCM and KHCM(Korea Highway Capacity Manual), capa챠y appears to correspond to confidence interval of 95%. Using the traffic flow rate at confidence interval of 95% the maximum hourly flow rate is 2, 187pcu at 95% of cummulative volume distribution, 2, 153pcu at 90%, 2, 215pcu at 85%. The study suggests that raional capacity esimation alternative is to take the 95% of cummulative distribution of observed hourly traffic flow at 95% confidence headway interval eliminating 5% long headway.(i.e. 95-95 rule)

• Journal of Korean Society of Steel Construction
• /
• v.9 no.1 s.30
• /
• pp.51-63
• /
• 1997

Highly curved steel-box bridges are usually constructed as ramp structures for the highway interchange and metropolitan elevated highway junction, but a number of these bridges are deteriorated and damaged to a significant degree due to heavy traffic. The main objective of the study is to develop a practical reliability-based assessment of safety and residual load carrying-capacity of existing curved steel-box ramp bridges. In the paper, for the realistic assessment of safety and residual load carrying-capacity of deteriorated and/or damaged curved steel-box bridges, an interactive non-linear limit state model is formulated based on the von Mises's combined stress yield criterion. It is demonstrated that the proposed model is effective for the assessment of reliability-based safety and the evaluation of residual load carrying-capacity of curved steel-box bridges. In addition, this study comparatively shows the applicability of various reliability analysis methods, and suggests a practical and effective one to be used in practice.

• Steel and Composite Structures
• /
• v.11 no.1
• /
• pp.1-19
• /
• 2011

The introduction of the Eurocodes makes plastic design criteria available also for composite bridges, leading to more economical solutions compared with previous elastic design rules. Particularly for refurbishment old bridges with higher actual traffic loads, up to date outside the scope of the Eurocodes, strengthening should therefore be avoidable or at least be necessary only to a minor extent. For bridges with smaller spans and compact cross sections, the plastic load bearing capacity is clearly justified. In this work, however, the focus is placed on long span continuous composite bridges with deep, longitudinally stiffened girders, susceptible to local buckling. In a first step, the elastic - plastic cross section capacity of the main girder in bending is studied as an isolated case, based on high preloads acting on the steel girder only, due to the common assembling procedure without scaffolding. In a second step, the effects on the whole structure are studied, because utilising the plastic section capacity at midspan leads to a redistribution of internal forces to the supports. Based on the comprehensive study of an old, actual strengthened composite bridge, some limitations for plastic design are identified. Moreover, fully plastic design will sometimes need additional global analysis. Practical recommendations are given for design purposes.

• Structural Monitoring and Maintenance
• /
• v.5 no.1
• /
• pp.93-110
• /
• 2018

In order to provide a novel strategy for long-span bridge health monitoring system design, this paper proposes a novel ultimate bearing capacity ratios based bridge internal force monitoring design method. The bridge ultimate bearing capacity analysis theories are briefly described. Then, based on the ultimate bearing capacity of the structural component, the component ultimate bearing capacity ratio, the uniformity of ultimate bearing capacity ratio, and the reference of component ultimate bearing capacity ratio are defined. Based on the defined indices, the high bearing components can then be found, and the internal force monitoring system can be designed. Finally, the proposed method is applied to the bridge health monitoring system design of the second highway bridge of Wuhu Yangtze river. Through the ultimate bearing capacity analysis of the bridge in eight load conditions, the high bearing components are found based on the proposed method. The bridge internal force monitoring system is then preliminary designed. The results show that the proposed method can provide quantitative criteria for sensors layout. The monitoring components based on the proposed method are consistent with the actual failure process of the bridge, and can reduce the monitoring of low bearing components. For the second highway bridge of Wuhu Yangtze river, only 59 components are designed to be monitored their internal forces. Therefore, the bridge internal force monitoring system based on the ultimate bearing capacity ratio can decrease the number of monitored components and the cost of the whole monitoring system.

• Korean Journal of Construction Engineering and Management
• /
• v.20 no.6
• /
• pp.44-56
• /
• 2019

Recently, the paradigm of SOC investment has shifted from new construction to maintenance. This shift became more important for the highway system because it is as one of the most important SOC. In Korea, highway maintenance costs are about 20% of the total annual highway construction budget, which is about two-thirds of developed countries. In addition, establishing standardized guidelines for the highway maintenance operation is not in place. Therefore, in order for domestic road construction and maintenance technology to secure competitiveness in the global construction market, it is urgent to improve the management capacity for maintenance as well as the technology and management capacity. This study examines highway maintenance practices in OECD countries such as North America, Europe, Australia, New Zealand, and Japan to identify core elements of highway maintenance practice. It is imperative to establish a comprehensive management system based upon asset management principle. Even if the budget for the highway construction is reduced, investment in maintenance needs to be maintained.

• Geomechanics and Engineering
• /
• v.7 no.2
• /
• pp.201-212
• /
• 2014

Due to the sea-crossing bridge span is generally large and main pier pile foundations are located in deep water and carry large vertical load, sea-crossing bridge main pier pile foundations bearing mechanism and load deformation characteristics are still vague. Authors studied the vertical bearing properties of sea-crossing bridge main pier pile foundations through pilot load tests. Large tonnage load test of Qingdao Bay Bridge main pier pile program is designed by using per-stressed technique to optimize the design of anchor pile reaction beam system. Test results show that the design is feasible and effective. This method can directly test bearing capacity of main pier pile foundations, and analysis bearing behaviors from test results of sensors which embedded in the pile. Through test study the vertical bearing properties of main pier pile foundation and compared with the generally short pile, author summarized the main pier pile foundations vertical bearing capacity and the main problem of design and construction which need to pay attention, and provide a reliable basis and experience for sea-crossing bridge main pier pile foundations design and construction.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.5
• /
• pp.467-476
• /
• 2001

The construction of highway bridges is almost complete in many countries including the United States. The government and highway agencies change the focus from constructing to maintaining To maintain the bridges effectively there is an urgent need to assess actual bridge loading carrying capacity and to predict their remaining life. The system reliability techniques have to be used for this purpose. Based on lifetime distribution (function) techniques this study illustrates how typical highway bridges can be modeled to predict their remaining life. The parameters of lifetime distribution are generated by Monte. The results can be used for optimization of planning interventions on existing bridges.