• Journal of Surface Science and Engineering
• /
• v.46 no.5
• /
• pp.208-215
• /
• 2013

The aim of the present study was to improve the radiative heat dissipation of aluminum alloy, Al 1050. Resin/CuO coating and Cu/CuO composite plating were applied on aluminum alloy to improve the radiative heat dissipation. Resin/CuO coating was made using thermosetting silicon resin and Cu/CuO composite plating was made in pyrophosphate copper plating bath. Radiant heat flux($W/m^2$) was measured by self-produced radiant heat measurement device to compare each specimen. The cross section of specimen and chemical bonding of surface were analyzed by FE-SEM, XPS and FT-IR. As a result, radiant heat of Resin/CuO coating was higher than Cu/CuO composite plating due to the adhesion with aluminum plate and the difference in chemical bonding. But, Both of them were higher than aluminum alloy. In order to confirm the result of experiment, aluminum plate, Resin/CuO coating and Cu/CuO composite plating sample were applied LED and measured the LED temperature. As a result, LED temperature of samples were matched previous results and confirmed coated samples were lower about 10 degrees than the aluminum alloy.

• Archives of Plastic Surgery
• /
• v.36 no.6
• /
• pp.679-684
• /
• 2009

Purpose: Human lipoaspirate cells are relatively easy to obtain in large quantities without cell culture. The aim of this in vitro pilot study was to determine the effect of cell therapy using uncultured lipoaspirate cells on cell proliferation and collagen synthesis of diabetic fibroblasts, which are the major contributing factors in wound healing. Methods: In order to get diabetic fibroblasts, dermis tissues were obtained from foot skin of diabetic patients who underwent debridements or toe amputations(n = 4). In order to isolate lipoaspirate cells, the same diabetic patients' abdominal adipose tissues were obtained by liposuction. The diabetic fibroblasts were co - cultured with or without autogenous lipoaspirate cells using porous culture plate insert. Initial numbers of the lipoaspirate cells and diabetic fibroblasts seeded were 15,000 cells/well, respectively. For cell proliferation assay, two treatment groups were included. In group I, diabetic fibroblasts were cultured with the insert having no cells, which serves as a control. In group II, the lipoaspirate cells were added in the culture plate insert. For collagen synthesis assay, one additional group(group III), in which diabetic fibroblasts were not seeded in the well and only lipoaspirate cells inside the insert were incubated without diabetic fibroblasts, was included for a reference. Results: One hundred to one hundred sixty thousand lipoaspirate cells were isolated per ml of aspirated adipose tissue. After 3 - day incubation, the mean cell numbers in group I and II were 17,294/well and 22,163/well. The mean collagen level in group I, II, and III were 29, 41, and 2 ng/ml, respectively. These results imply that both cell proliferation and collagen synthesis in the lipoaspirate cell treatment group were 28 and 44 percents higher than in the control group, respectively(p < 0.05). Conclusion: Uncultured lipoaspirate cell autografts may stimulate the wound healing activity of diabetic fibroblasts.

• Steel and Composite Structures
• /
• v.30 no.1
• /
• pp.13-29
• /
• 2019

This work presents the buckling investigation of functionally graded plates resting on two parameter elastic foundations by using a new hyperbolic plate theory. The main advantage of this theory is that, in addition to including the shear deformation effect, the displacement field is modelled with only four unknowns and which is even less than the first order shear deformation theory (FSDT) and higher-order shear deformation theory (HSDT) by introducing undetermined integral terms, hence it is unnecessary to use shear correction factors. The governing equations are derived using Hamilton's principle and solved using Navier's steps. The validation of the proposed theoretical model is performed to demonstrate the efficacy of the model. The effects of various parameters like the Winkler and Pasternak modulus coefficients, inhomogeneity parameter, aspect ratio and thickness ratio on the behaviour of the functionally graded plates are studied. It can be concluded that the present theory is not only accurate but also simple in predicting the critical buckling loads of functionally graded plates on elastic foundation.

• Steel and Composite Structures
• /
• v.39 no.1
• /
• pp.51-64
• /
• 2021

This paper presents a high-order shear and normal deformation theory for the bending of FGM plates. The number of unknowns and governing equations of the present theory is reduced, and hence makes it simple to use. Unlike any other theory, the number of unknown functions involved in displacement field is only four, as against five or more in the case of other shear and normal deformation theories. Based on the novel shear and normal deformation theory, the position of neutral surface is determined and the governing equilibrium equations based on neutral surface are derived. There is no stretching-bending coupling effect in the neutral surface-based formulation, and consequently, the governing equations of functionally graded plates based on neutral surface have the simple forms as those of isotropic plates. Navier-type analytical solution is obtained for functionally graded plate subjected to transverse load for simply supported boundary conditions. The accuracy of the present theory is verified by comparing the obtained results with other quasi-3D higher-order theories reported in the literature. Other numerical examples are also presented to show the influences of the volume fraction distribution, geometrical parameters and power law index on the bending responses of the FGM plates are studied.

• Structural Engineering and Mechanics
• /
• v.81 no.6
• /
• pp.691-703
• /
• 2022

To obtain the seismic response of lead-cored rubber, shape memory alloy (SMA)-rubber isolation Plate-shell Integrated Concrete Liquid-Storage Structure (PSICLSS), based on a PSICLSS in a water treatment plant, built a scale experimental model, and a shaking table test was conducted. Discussed the seismic responses of rubber isolation, SMA-rubber isolation PSICLSS. Combined with numerical model analysis, the vibration characteristics of rubber isolation PSICLSS are studied. The results showed that the acceleration, liquid sloshing height, hydrodynamic pressure of rubber and SMA-rubber isolation PSICLSS are amplified when the frequency of seismic excitation is close to the main frequency of the isolation PSICLSS. The earthquake causes a significant leakage of liquid, at the same time, the external liquid sloshing height is significantly higher than internal liquid sloshing height. Numerical analysis showed that the low-frequency acceleration excitation causes a more significant dynamic response of PSICLSS. The sinusoidal excitation with first-order sloshing frequency of internal liquid causes a more significant sloshing height of the internal liquid, but has little effect on the structural principal stresses. The sinusoidal excitation with first-order sloshing frequency of external liquid causes the most enormous structural principal stress, and a more significant external liquid sloshing height. In particular, the principal stress of PSICLSSS with long isolation period will be significantly enlarged. Therefore, the stiffness of the isolation layer should be properly adjusted in the design of rubber and SMA-rubber isolation PSICLSS.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.44-56
• /
• 1993

The purpose of this paper is to analyze the impact response behaviors of glass/epoxy laminated composite plates subjected to the transversely impact of a steel ball. For this purpose, dynamic finite element analysis based on the higher-order shear defomation plate theory is used to compute the contact forces, rebound velocity of a steel ball, and dynamic strain response histories. And low-velocity and high-velocity impact experiments were conducted to compare the results and compute the wave propagation velocities. The results obtained from impact experiments are in good agreement with those of dynamic finite element analysis. Also the wave propagation velocities obtained from high-velocity impact experiments and wave propagation theory agree well, and wave velocities were higher in the smaller radius of steel ball.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2005.04a
• /
• pp.335-342
• /
• 2005

Using higher order Mindlin plates and piezoelectric materials, eigenvalue problems are considered. Since piezoelectric crystal resonators produce a proper amount of electric signal for a thickness-shear frequency, the objective is to decouple the thickness-shear mode from the others. Design variables are the bulk material densities corresponding to the mass of masking plates for electrodes. The design sensitivity expressions for the thickness-shear frequency and mode shape vector are derived using direct differentiation method(DDM). Using the developed design sensitivity analysis (DSA) method, we formulate a topology optimization problem whose objective function is to maximize the thickness-shear component of strain energy density at the thickness-shear mode. Constraints are the allowable volume and area of masking plate. Numerical examples show that the optimal design yields an improved mode shape and thickness-shear energy.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.281-284
• /
• 2004

Photo-induced memory effect of an organic light-emitting diode(OLED) composed of a hydrazone-derivative(DBAH) dispersed in bis-phenol-A type polycarbonate polymer(PCA) in the presence of thio-Michler's ketone, was investigated by the measuring of the current density and luminance at the various conditions. After the light exposure, the current of the OLED was decreased approximately one order, and the luminance of the OLED also decresed. This memory effct was erasable by heating the OLED to the temperature higher than the glass transition temperature(Tg). As shown in this result, we found the memory effect was erased by heating and returned to its original state in the hole injecting layer(HIL) of the OLED. A series of these phenomena was suggested the possibility of the application to the imaging plate.

• Transactions of Materials Processing
• /
• v.22 no.1
• /
• pp.48-53
• /
• 2013

As the adoption of injection molding technology increases, injected-molded optical products require higher dimensional accuracy and optical stability than ever before. In the present study, four kinds of molding methods, i.e., conventional injection molding (CIM), injection/compression molding (ICM), rapid heat and cooling the mold(RHCM) and rapid injection/compression molding (RICM) were selected in order to investigate the optical anisotropy of a 7 inch Light Guide Plate(LGP) by examining the gap-wise distribution of birefringence and the extinction angle. The results indicate that the compression process can decrease flow-induced birefringence over the whole region and that rapid heating can decrease the birefringence level better than conventional molding. In addition, for the combination of compression and rapid heating a reversal flow was detected from the distribution of the extinction angle near the gate.

• Journal of KSNVE
• /
• v.7 no.1
• /
• pp.161-168
• /
• 1997

The present paper describes the vibration control experiment of composite plates with bonded piezoelectric sensor and actuator. The system is modeled as two degree-of-freedom system using modal coordinates and the system parameters are obtained from vibration tests. Kalman filter is adopted for extracting modal coordinates from sensor signal, and control algorithms applied to the system are Linear Quadratic Gaussian(LQG) control, Bang-Bang Control (BBC), Negative Velocity Feedback(NVF), Proportional Derivative Control(PDC). From observation of the spillover and control perfomance, it is concluded that a higher order control algorithm such as LQG rather than BBG, NVF, PDC is suitable for efficient simultaneous control of both bending and twisting modes of composite plates.