• International Journal of Highway Engineering
• /
• v.18 no.3
• /
• pp.87-94
• /
• 2016

PURPOSES : This study analyzed the lane-by-lane traffic flow characteristics in Korea by using real-world data, including congestion levels, for 2-, 3-, and 4-lane freeways. METHODS : On the basis of a literature review, lane flow and speed characteristics were analyzed using flow measurements and speed ratios. In addition, the effect of congestion levels on traffic flow were visualized using rescaled cumulative plots. RESULTS : Driver behavior varied depending on the congestion level. During free-flow conditions, the lane-use ratio of individual lanes varied largely, whereas during congestion, the ratio was nearly the same for all lanes (i.e., equilibrium). During maximum-flow and congestion conditions, the median lane was used more than the shoulder lane, whereas during all other conditions, the shoulder lane had a higher lane-use ratio. In 3- or 4-lane freeways, the lane-use ratio of the median lane always exceeded 1 and was the highest during free-flow conditions. CONCLUSIONS : The results of the present analysis can be used as an index to predict congestion before a lane is overcapacitated. Moreover, the results can be applied in variable lane guidance systems, such as car navigation systems and variable message displays, to control traffic flow.

• International Journal of Highway Engineering
• /
• v.18 no.5
• /
• pp.117-125
• /
• 2016

PURPOSES : The density in uninterrupted traffic flow facilities plays an important role in representing the current status of traffic flow. For example, the density is used for the primary measures of effectiveness in the capacity analysis for freeway facilities. Therefore, the estimation of density has been a long and tough task for traffic engineers for a long time. This study was initiated to evaluate the performance of density values that were estimated using VDS data and two traditional methods, including a method using traffic flow theory and another method using occupancy by comparing the density values estimated using vehicular trajectory data generated from a radar detector. METHODS : In this study, a radar detector which can generate very accurate vehicular trajectory within the range of 250 m on the Joongbu expressway near to Dongseoul tollgate, where two VDS were already installed. The first task was to estimate densities using different data and methods. Thus, the density values were estimated using two traditional methods and the VDS data on the Joongbu expressway. The density values were compared with those estimated using the vehicular trajectory data in order to evaluate the quality of density estimation. Then, the relationship between the space mean speed and density were drawn using two sets of densities and speeds based on the VDS data and one set of those using the radar detector data. CONCLUSIONS : As a result, the three sets of density showed minor differences when the density values were under 20 vehicles per km per lane. However, as the density values become greater than 20 vehicles per km per lane, the three methods showed a significant difference among on another. The density using the vehicular trajectory data showed the lowest values in general. Based on the in-depth study, it was found out that the space mean speed plays a critical role in the calculation of density. The speed estimated from the VDS data was higher than that from the radar detector. In order to validate the difference in the speed data, the traffic flow models using the relationships between the space mean speed and the density were carefully examined in this study. Conclusively, the traffic flow models generated using the radar data seems to be more realistic.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.8
• /
• pp.34-41
• /
• 2017

Vehicle to Infrastructure(V2I) communication means the technology between the vehicle and the roadside unit to provide the Intelligent Transportation Systems(ITS) and Telematic services. The vehicle collects information about the probe data through the evolved Node B(eNodeB) and after that eNodeB provides road conditions or traffic information to the vehicle. To provide these V2I communication services, we need a link adaptation technology that enables reliable and higher transmission rate. The receiver transmits the estimated Channel State Information(CSI) to transmitter, which uses this information to enable the link adaptation. However, due to the rapid channel variation caused by vehicle speed and the processing delay between the layers, the estimated CSI quickly becomes outdated. For this reason, channel interpolation and prediction scheme are needed to achieve link adaptation in V2I communication system. We propose the Advanced Discrete Prolate Spheroidal Sequence(ADPSS) channel interpolation and prediction scheme. The proposed scheme creates an orthonomal basis, and uses a correlation matrix to interpolate and predict channel. Also, smoothing is applied to frequency domain for noise removal. Simulation results show that the proposed scheme outperforms conventional schemes with the high speed and low speed vehicle in the freeway and urban environment.

• Journal of Korean Society of Transportation
• /
• v.29 no.5
• /
• pp.121-138
• /
• 2011

More affordable and available cutting-edge technologies (e.g., wireless vehicle communication) are regarded as a possible alternative to the fixed infrastructure-based traffic information system requiring the expensive infrastructure investments and mostly implemented in the uninterrupted freeway network with limited spatial system expansion. This paper develops an advanced decentralized traveler information System (ATIS) using vehicle-to-vehicle (V2V) communication system whose performance (drivers' travel time savings) are enhanced by three complementary functions (autonomous automatic incident detection algorithm, reliable sample size function, and driver behavior model) and evaluates it in the typical $6{\times}6$ urban grid network with non-recurrent traffic state (traffic incident) with the varying key parameters (traffic flow, communication radio range, and penetration ratio), employing the off-the-shelf microscopic simulation model (VISSIM) under the ideal vehicle communication environment. Simulation outputs indicate that as the three key parameters are increased more participating vehicles are involved for traffic data propagation in the less communication groups at the faster data dissemination speed. Also, participating vehicles saved their travel time by dynamically updating the up-to-date traffic states and searching for the new route. Focusing on the travel time difference of (instant) re-routing vehicles, lower traffic flow cases saved more time than higher traffic flow ones. This is because a relatively small number of vehicles in 300vph case re-route during the most system-efficient time period (the early time of the traffic incident) but more vehicles in 514vph case re-route during less system-efficient time period, even after the incident is resolved. Also, normally re-routings on the network-entering links saved more travel time than any other places inside the network except the case where the direct effect of traffic incident triggers vehicle re-routings during the effective incident time period and the location and direction of the incident link determines the spatial distribution of re-routing vehicles.