• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.879-882
• /
• 1992

In order to study electrical properties of epoxy composites with various additives rates and curing conditions, dielectric measurements have been performed over a frequency range from 30 [Hz] to 3 [MHz] and a temperature range of 20[$^{\circ}C$]$\sim$180[$^{\circ}C$] The observed higher values of dielectric permittivity and loss In the case of filled epoxy are attributed to MWS polarization effect. The low temperature peak assigned to the $\beta$-relaxation process is attributed to the enhenced rotation of the methyl group attached to the main chain and the presence of filler. And the high temperature peak ($\alpha$-relaxation process)is associated with the segmental motion or glass transition process.

• Journal of Powder Materials
• /
• v.15 no.4
• /
• pp.292-296
• /
• 2008

The electromagnetic (EM) wave absorption properties of the $Fe_{73}Si_{16}B_7Nb_3Cu_1$ nanocrystalline powder mixed with 5 to 20 vol% of Ni-Zn ferrites has been investigated in a frequency range from 100MHz to 10GHz. Amorphous ribbons prepared by a planar flow casting process were pulverized and milled after annealing at 425 for 1 hour. The powder was mixed with a ferrite powder at various volume ratios to tape-cast into a 1.0mm thick sheet. Results showed that the EM wave absorption sheet with Ni-Zn ferrite powder reduced complex permittivity due to low dielectric constant of ferrite compared with nanocrystalline powder, while that with 5 vol% of ferrite showed relatively higher imaginary part of permeability. The sheet mixed with 5 vol% ferrite powder showed the best electromagnetic wave absorption properties at high frequency ranges, which resulted from the increased imaginary part of permeability due to reduced eddy current.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.1-4
• /
• 2008

The electrical characteristics of polycrystalline silicon (poly-Si) thin film transistor (TFT) crystallized by excimer laser annealing (ELA) method were evaluated, The polycrystalline silicon thin-film transistor (poly-Si TFT) has higher electric field-effect-mobility and larger drivability than the amorphous silicon TFT. However, to poly-Si TFT's using conventional processes, the temperature must be very high. For this reason, an amorphous silicon film on a buried oxide was crystallized by annealing with a KrF excimer laser (248 nm)to fabricate a poly-Si film at low temperature. Then, High permittivity $HfO_2$ of 20 nm as the gate-insulator was deposited by atomic layer deposition (ALD) to low temperature process. In addition, the solid phase crystallization (SPC) was compared to the ELA method as a crystallization technique of amorphous-silicon film. As a result, the crystallinity and surface roughness of poly-Si crystallized by ELA method was superior to the SPC method. Also, we obtained excellent device characteristics from the Poly-Si TFT fabricated by the ELA crystallization method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.271-271
• /
• 2010

$BaTiO_3$(BT) has high permittivity so that has been applied to dielectric and insulator materials in 3D system-level package integration. In order to achieve excellent performance of device, the BT layer should be highly dense. In this study, BT thick films were prepared by the inkjet printing method. And these films were cured at $280^{\circ}C$ after infiltration of polymer resin. As a result, we have successfully fabricated not only the inkjet-printed hybrid BT film but also metal-insulator-metal(MIM) capacitor without sintering process. Changes in the dielectric constant of BT hybrid film with particle size and packing density were investigated. The dielectric constant was increased with increasing packing density and particle size. Further, the BT hybrid film using two different size particles had even higher packing density and dielectric constant.

• Korean Journal of Metals and Materials
• /
• v.47 no.12
• /
• pp.866-872
• /
• 2009

The effects of magnetic powder thickness on electromagnetic wave absorption characteristics in Fe-6.5Si-0.9Cr (wt%) alloy flakes/polymer composite sheets available for quasi-microwave band have been investigated. The atomized FeSiCr powders were milled by using attritor for 12, 24, and 36 h, powder thickness changed from $40{\mu}m$ to $3{\mu}m$ upon 36 h milling. The composite sheet, including thinned magnetic flakes, exhibited higher power loss in the GHz frequency range as compared with the sheets having thick flakes. Moreover, both the complex permeability and the loss factor increased with the decrease in thickness of the alloy flakes. Therefore, the enhanced power loss property of the sheets containing thin alloy flakes was attributed to the flakes of high complex permeability, especially their imaginary part. Additionally, the complex permittivity was also increased with the reduction of flake thickness, and this behavior was considered to be helpful for improvement of the electromagnetic wave absorption characteristics in the composite sheets, including thin alloy flakes.

• Korean Journal of Food Science and Technology
• /
• v.31 no.1
• /
• pp.122-127
• /
• 1999

Quality changes of Korean ginseng on microwave drying were determined in terms of water activity, crude protein, crude lipid, crude ash, dielectric properties, content of sugar, ginsenoside composion, microstructure. Korean fresh ginseng were subjected to four different processing : 3 min microwave drying and 2 min holding-24 hrs drying (MWI), 5 min microwave drying and 2.5 min holding-24 hrs drying (MW2), 3 min microwave drying and 2 min holding-12 hrs after hot air drying for 12 hrs drying at $45^{\circ}C$ (MWH1), 5 min microwave drying and 2.5 min holding-12 hrs drying after hot air drying for 12 hrs at $45^{\circ}C$ (MWH2), Water content was decreased 14.33% without shrinkage and water activity was 0.57 after microwave drying. Permittivity was increased as water content increased. As temperature increased, permittivity was increased until $40^{\circ}C$ and fast decreased over $40^{\circ}C$. Content of ginsenoside for MW1 and MW2 was higher than that of MWH1 and MWH2. Data of free sugar showed that there was no significant difference in each treatment. The MW2 dried ginseng showed a more compact structure than the MWH2 ginseng.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.3169-3175
• /
• 2011

This paper describes the design of size-reduced directional coupler using the artificial dielectric substrate and its increased effective permittivity. Directional couplers are widely used in measuring RF power indirectly and coupling signal power. Artificial dielectric substrates have higher effective dielectric constant than standard dielectric substrate due to the lots of metalized via-holes, and the increased effective permittivity results in size-reduction of circuits. As a design example, 15dB directional couplers are designed on the standard substrate and artificial dielectric substrate and their size are compared. The size of the directional coupler using the artificial dielectric substrate is only 1/3 of that designed using the standard substrate, while the performances are preserved. In addition, the measured performances of the size-reduced coupler are well agreed with the simulated ones. The measured coupling coefficient, matching, and insertion loss at 2GHz are -14.62dB, -24.1dB, and -0.38dB, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.70-75
• /
• 2017

In this paper, we studied the RF characteristics of a voltage-controlled artificial transmission line employing periodically arrayed diodes for application to highly miniaturized wireless communication systems on an MMIC (monolithic microwave integrated circuit). According to the results, the novel voltage-controlled artificial transmission line employing periodically arrayed diodes exhibited a short wave length, which was only 35.2% that of the conventional transmission line, owing to increasing capacitance. In addition, it's effective permittivity and effective propagation constant exhibited considerably higher values than those of the conventional transmission line. Furthermore, attenuation constant of the voltage-controlled artificial transmission line was far higher than that of the conventional transmission line. Using the closed-form equation, we theoretically analyzed the equivalent circuit of the voltage-controlled artificial transmission line.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.5
• /
• pp.698-707
• /
• 1998

For inverse scattering problems reconstructing cross-sectional permittivity distributions of dielectric cylinders, the angular spectral inverse technique using the moment method with pulse basis function suffers from large reconstruction error even if very small noise due to requiring the higher spectral informations on the larger cross-section of the cylinder. To reduce the number of higher-order spectra, this paper presents an improved inverse technique in angular spectral domain applying the moment procedure with a series-expansion basis function for the induced field in each enlarged cross-sectional cell. By choosing adequate spectra and averaging over the enlarged cells with a suitable weighting function, the reconstruction profiles reveal fine enough to suppress the noise effect significantly.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.3
• /
• pp.142-145
• /
• 2015

In this work, open stubs were fabricated on a polyether sulfone (PES) substrate, and their basic radio frequency (RF) characteristics were investigated for application to RF matching components of a flexible monolithic microwave integrated circuit (MMIC). According to the results, an open stub employing coplanar waveguide (OSCPW) on PES exhibited much lower loss than that on silicon substrate. The OSCPW with a length of $500{\mu}m$ on PES showed capacitance values of 0.031 ~ 0.044 pF from 0.5 to 50 GHz. For application to a relatively high-value capacitive matching, an open stub employing a fishbone-type transmission line (OSFTTL) was fabricated on PES, and its characteristics were investigated. The OSFTTL showed much higher capacitance values than the OSCPW due to the high effective permittivity value. Specifically, the OSFTTL on PES showed capacitance values of 0.066 ~ 0.24 pF from 0.5 to 50 GHz, which are higher than those for the open stub on silicon substrate. The above results indicate that the OSCPW and OSFTTL on PES can be effectively used for application to low/high-value capacitive matching components on microwave and millimeter wave flexible MMIC. To the best of the authors' knowledge, this work is the first report of the investigation of RF capacitive matching components on PES substrate.