• Journal of Korean Vacuum Science & Technology
• /
• v.2 no.2
• /
• pp.57-62
• /
• 1998

The resonance frequencies, shunt impedances and Q-values for the higher-order modes in our designed cavity are calculated by the computer codes URMEL and MAFIA. A new computer code is developed to calculate the complex tune shifts for the randomness of the higher-order mode frequencies due to the construction errors of a cavity. The results with the construction errors are compared to those fo without error cases for the dipole mode and quadrupole mode.

• Structural Engineering and Mechanics
• /
• v.48 no.3
• /
• pp.415-434
• /
• 2013

This work is concerned with transverse vibrations of axially traveling nanobeams including strain gradient and thermal effects. The strain gradient elasticity theory and the temperature field are taken into consideration. A new higher-order differential equation of motion is derived from the variational principle and the corresponding higher-order non-classical boundary conditions including simple, clamped, cantilevered supports and their higher-order "offspring" are established. Effects of strain gradient nanoscale parameter, temperature change, shape parameter and axial traction on the natural frequencies are presented and discussed through some numerical examples. It is concluded that the factors mentioned above significantly influence the dynamic behaviors of an axially traveling nanobeam. In particular, the strain gradient effect tends to induce higher vibration frequencies as compared to an axially traveling macro beams based on the classical vibration theory without strain gradient effect.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.10B
• /
• pp.1885-1894
• /
• 1999

The higher mode cutoff frequencies in Crawford TEM cells computed by the Galerkin method(GM) describe in this paper. The authors also report the half mode boundaries to solve not only the cut-off frequencies of symmetric TEM cells and those of asymmetric TEM cells. It is shown that the measured resonant frequencies of the present symmetric TEM cells and a designed asymmetric TEM cell are agreed with the calculated results.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.7 no.1
• /
• pp.116-125
• /
• 1995

Higher order nonlinear transfer functions are applied to model the nonlinear responses obtained Inn dynamic analysis of single degree of freedom systems (SDOF) subjected to wave and current loadings. The structural systems are subjected to single harmonic, two wave combination and irregular wave loading. Three different sources of nonlinearities are examined for each of the wave loading condition and it is shown that the nonlinear response appear at the resonance frequencies of the SDOF even when virtually no wave energy exists at those resonance frequencies. Higher order nonlinear transfer functions based on Volterra series representation are used to model the nonlinear responses mainly f3r the flexible systems and clearly shows the degrees of nonlinearity either as quadratic or cubic.

• Journal of the Korean Data and Information Science Society
• /
• v.21 no.3
• /
• pp.427-435
• /
• 2010

In this study, we develop clinical pathways for test and medical treatment items of acute appendicitis patients in emergency room. In order to develop the clinical pathways, we first employ the order selection method by Park et al. (2010), and then display the selected orders in such a way that associated orders are tied together. More specifically the order selection method that we employ is based on lift and, starting from the orders with higher frequencies, sequentially removes the negatively associated orders with lift values less than 0.9. The way associated orders are selected and tied together is similar to that of the order selection method. More specifically, starting from the selected orders with higher frequencies, the orders with lift values greater than 1.1 are considered associated and displayed to the right of the corresponding order. Therefore, in the diagram of clinical pathways, the orders at the left hand side, in principle, are not associated with each other and upper orders have higher frequencies, and associated orders are located to the right of corresponding order at the left hand side and more left orders, in principle, have higher frequencies.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.6
• /
• pp.847-854
• /
• 1999

In this paper, we have analysed frequency-dispersion characteristics of higher-order modes for uniform planar transmission lines, using the 2-dimensional finite-difference time-domain method. The method presented in this paper uses both informations of amplitude and phase of the electromagnetic spectrum to determine resonant frequencies, while methods previously reported use the magnitude only. This algorithm is very useful when a resonant mode has a relatively small magnitude, where the identification of the resonant mode is quite difficult. Numerical results show that a strip line supports few higher-order modes within the frequency range of 20 GHz, but there occur many higher-order modes in the structure of grounded coplanar waveguide, where resonant frequencies of the first higher-order mode is very close to those of the fundamental mode and there occur lots of very adjacent higher-order modes. As in this example, for the analysis of planar transmission lines which support many resonant modes very close each other, the method presented in this paper can be applied very efficiently.

• Steel and Composite Structures
• /
• v.16 no.5
• /
• pp.507-519
• /
• 2014

In this paper, a higher order shear deformation beam theory is developed for static and free vibration analysis of functionally graded beams. The theory account for higher-order variation of transverse shear strain through the depth of the beam and satisfies the zero traction boundary conditions on the surfaces of the beam without using shear correction factors. The material properties of the functionally graded beam are assumed to vary according to power law distribution of the volume fraction of the constituents. Based on the present higher-order shear deformation beam theory, the equations of motion are derived from Hamilton's principle. Navier type solution method was used to obtain frequencies. Different higher order shear deformation theories and classical beam theories were used in the analysis. A static and free vibration frequency is given for different material properties. The accuracy of the present solutions is verified by comparing the obtained results with the existing solutions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.170-175
• /
• 2002

The cut-off frequencies of higher order modes in a symmetrical stripline are calculated using the variational finite element method combined with the conformal mapping. The conformal mapping is used to Improve the modeling of the infinite transverse extents of a stripline. And then the finite element method is employed to solve the variational equation in the transformed finite region. Comparisons with numerical results found in the literature validate the presented method.

• Structural Engineering and Mechanics
• /
• v.27 no.1
• /
• pp.1-16
• /
• 2007

In the present study, a spline finite strip with higher-order shear deformation is formulated for the stability and free vibration analysis of composite plates. The analysis is conducted based on Reddy's third-order shear deformation theory, Touratier's "Sine" model, Afaq's exponential model and Cho's higher-order zigzag laminate theory. Consequently, the shear correction coefficients are not required in the analysis, and an improved accuracy for thick laminates is achieved. The numerical results, based on different shear deformation theories, are presented in comparison with the three-dimensional elasticity solutions. The effects of length-to-thickness ratio, fibre orientation, and boundary conditions on the critical buckling loads and natural frequencies are investigated through numerical examples.

• Structural Engineering and Mechanics
• /
• v.70 no.5
• /
• pp.601-621
• /
• 2019

This study presents a comprehensive nonlinear dynamic approach to investigate the linear and nonlinear vibration of sandwich plates fabricated from functionally graded materials (FGMs) resting on an elastic foundation. Higher-order shear deformation theory and Hamilton's principle are employed to obtain governing equations. The Runge-Kutta method is employed together with the commercially available mathematical software MAPLE 14 to solve the set of nonlinear dynamic governing equations. Method validity is evaluated by comparing the results of this study and those of previous research. Good agreement is achieved. The effects of temperature change on frequencies are investigated considering various temperatures and various volume fraction index values, N. As the temperature increased, the plate frequency decreased, whereas with increasing N, the plate frequency increased. The effects of the side-to-thickness ratio, c/h, on natural frequencies were investigated. With increasing c/h, the frequencies increased nonlinearly. The effects of foundation stiffness on nonlinear vibration of the sandwich plate were also studied. Backbone curves presenting the variation of maximum displacement with respect to plate frequency are presented to provide insight into the nonlinear vibration and dynamic behavior of FGM sandwich plates.