• ETRI Journal
• /
• 제29권4호
• /
• pp.452-456
• /
• 2007

Very compact 4-channel 200-GHz-spacing external cavity lasers (ECLs) were fabricated by hybrid integration of reflection gratings and superluminescent laser diodes on a planar lightwave circuit chip. The fifth-order gratings as reflection gratings were formed using a conventional contact-mask photo-lithography process to achieve low-cost fabrication. The lasing wavelength of the fabricated ECLs matched the ITU grid with an accuracy of ${\pm}0.1$ nm, and optical powers were more than 0.4 mW at the injection current of 80 mA for all channels. The ECLs showed single mode operations with more than 30 dB side lobe suppression.

• Smart Structures and Systems
• /
• 제13권4호
• /
• pp.637-657
• /
• 2014

This paper presents a dynamic analysis of three-dimensional beams. Structures made of functionally graded materials are considered. Several higher-order as well as classical theories are derived by means of a compact notation for the a-priori expansion order of the displacement field over the beam cross-section. The governing differential equations and boundary conditions are obtained in a condensed nuclear form that does not depend on the kinematic hypotheses. The problem is, then, exactly solved in space by means of a Navier-type solution, whereas time integration is performed by means of Newmark's solution scheme. Slender and short simply supported beams are investigated. Results are validated towards three-dimensional FEM results obtained via the commercial software ANSYS. Numerical investigations show that good accuracy can be obtained through the proposed formulation provided that the appropriate expansion order is considered.

• 한국산업융합학회 논문집
• /
• 제4권2호
• /
• pp.167-175
• /
• 2001

In this study, a general perturbation method is presented to reanalysis dynamic response of base-isolated systems. The perturbation is expanded to general order and which provide the formulation of perturbed solutions. in which eigensolutions of non-modified system are treated as unperturbed solutions. The accuracy of present method is tested using a 2-DOF system with isolator, where the stiffness and damping coefficients of isolator are changed, respectively, The reanalyzed eigensolutions and response using perturbed solutions are successfully approached to exact ones after just first perturbation. Supposing the practical criterion as ${\pm}5%$ error, the modification range of -50%~30% from original system can be allowed for the first order perturbation. Using higher order solutions, the applicable range will be wide.

• 대한치과보철학회지
• /
• 제40권1호
• /
• pp.18-29
• /
• 2002

As the inaccuracy which was made in implant impression prevented passive fit, it needed to solder the sectioned framework at several locations to correct the inaccuracy. Many clinicians have suggested impression techniques which could make passive fit between implant and superstructure. The purpose of this research was to measure and compare the accuracy of three methods of taking impression with the strain amplifier. The experimental groups were classified as follows : Group I : splinted the two parts with $Futar^{(R)}D$ Occlusion. Group II : splinted the two parts with $DuraLay^{(R)}$. Group III ; didn't splint the two parts. The results were as follows ; 1. The values of strain in the vertical and horizontal surfaces were increased in the order of group I, group II and group III. 2. Group 1 showed higher accuracy of the duplicated casts in the vortical and horizontal sur faces than group II and group III (p<0.05). 3. There were no significant differences in the accuracy of the duplicated casts between group II and group III. From the above results, it is considered that the splinting method of impression copings could make an influence on the accuracy of the master casts. To improve the accuracy of the master casts, splinting the squared impression copings with the additional silicone occlusion materials is recommendable.

• 대한공간정보학회지
• /
• 제19권3호
• /
• pp.115-125
• /
• 2011

최근 이슈가 되어온 스마트폰에는 고해상도 카메라, Assisted GPS, 가속도계, 자이로스코프, 그리고 자기 계측 센서와 같이 측량에 직접 이용할 수 있는 다양한 센서들이 탑재되어 있다. 본 연구는 고해상도 영상을 제공하는 스마트폰 카메라를 검정하고 그 정확도를 평가함으로써, 사진측량에 스마트폰 영상의 활용 가능성을 제시하는데 그 목적을 둔다. 먼저, 스마트폰 카메라의 정확도 평가에 앞서 각 카메라의 렌즈 왜곡을 보정하기 위한 카메라 검정이 이루어졌고, 이 과정에서 광속조정에 의해 계산된 영상 좌표 및 대상물 좌표의 정확도를 분석하였다. 또한, 3차원 위치 결정에 있어 렌즈 왜곡 계수의 고려 유무에 따른 결과 분석이 이루어졌고, 최종적으로 측량용 카메라에 대한 스마트폰 카메라의 상대 정확도를 평가하였다. 그 결과, 스마트폰 카메라의 왜곡 보정에 있어 고차항의 방사 왜곡 계수도 고려되어야 하며, 측량용 카메라에 의한 결과와 미소한 차이를 나타내어 사진측량에 스마트폰 영상의 활용 가능성이 클 것으로 기대된다.

• 대한전자공학회논문지SP
• /
• 제43권2호
• /
• pp.87-92
• /
• 2006

Array 신호처리에서 복소 지수함수의 합으로 구성된 신호의 파라미터를 추정하는데 고차 통계를 이용할 수 있다. 본 논문에서는 4차 cumulant를 이용한 고차 Matrix Pencil method(MPM)를 제안하였다. 4차 cumulant는 Gaussian 잡음를 억제할 수 있기 때문에, MPM의 응답은 기존의 방법에 비하여 더 좋은 잡음 면역을 가지고 있다. 본 논문에서는 높은 정확성을 가지는 MPM의 모든 장점을 유지하면서 성공적으로 고차 MPM을 공식화하였다. 그리고 Numerical simulation을 통해서 본 논문에서 제안된 4차 cumulant를 이용한 방법이 Gaussian 잡음환경에서 더 우수한 DOA 분해능을 가지고 있음을 증명하였다.

• Structural Monitoring and Maintenance
• /
• 제5권3호
• /
• pp.417-428
• /
• 2018

In this paper, various model reduction methods were assessed using a shear frame, plane and space truss structures. Each of the structures is one-dimensional, two-dimensional and three-dimensional, respectively. Three scenarios of poor, better, and the best were considered for each of the structures in which 25%, 40%, and 60% of the total degrees of freedom (DOFs) were measured in each of them, respectively. Natural frequencies of the full and reduced order structures were compared in each of the numerical examples to assess the performance of model reduction methods. Generally, it was found that system equivalent reduction expansion process (SEREP) provides full accuracy in the model reduction in all of the numerical examples and scenarios. Iterated improved reduced system (IIRS) was the second-best, providing acceptable results and lower error in higher modes in comparison to the improved reduced system (IRS) method. Although the Guyan's method has very low levels of accuracy. Structures were classified with the excitation frequency. High-frequency structures compared to low-frequency structures have been poor performance in the model reduction methods (Guyan, IRS, and IIRS).

• 한국조경학회지
• /
• 제26권2호
• /
• pp.251-258
• /
• 1998

The purposes of this study was to investigate accuracy and indigenity of landscape plant species in planting design and construction at housing complex and offer basic data for improving precision of planting construction. The scientific name of landscape plant species was described in planting drawings at only two sites among twelve survey sites. According to analysis on indigenity of plant species in planting drawings, it was found that the component ratio of foreign species was the highest and the component ratio of native species at public housing complex was the lowest. The component ratio of landscape plant species in planting construction was severely differed to that of planting drawings. Also the component ratio of cultivar was higher than that of planting drawings due to planting of sevveral cultivars for one species in planting drawings. In the result of accuracy analysis on landscape plant species in planting construction, it was found that mean ratio of inacccurate species was 33.2% at public housing complex, 29.6% at local company housing complex and 26.4% at nationwide company housing complex. It was found that several cultivars were planted for one species in planting drawings. The representative species which were planted by several cultivars were Camellia japonica, Rododendron spp., Prunus spp. and Magnolia spp. and so on. In order to promote the precision and speciality of planting design and construction, scientific and cultivar name of plants should be described in planting drawings.

• 대한원격탐사학회지
• /
• 제31권4호
• /
• pp.337-346
• /
• 2015

Water body extraction based on backscatter information is an essential process to analyze floodaffected areas from Synthetic Aperture Radar (SAR) image. Water body in SAR image tends to have low backscatter values due to homogeneous surface of water, while non-water body has higher backscatter values than water body. Non-water body, however, may also have low backscatter values in high resolution SAR image such as Kompsat-5 image, depending on surface characteristic of the ground. The objective of this paper is to present a method to increase backscatter contrast between water body and non-water body and also to remove efficiently misclassified pixels beyond true water body area. We create an entropy image using a Gray Level Co-occurrence Matrix (GLCM) and classify the entropy image into water body and non-water body pixels by thresholding of the entropy image. In order to reduce the effect of threshold value, we also propose Water Body Texture Index (WBTI), which measures simultaneously the occurrence of repeated water body pixel pair and the uniformity of water body in the binary entropy image. The proposed method produced high overall accuracy of 99.00% and Kappa coefficient of 90.38% in water body extraction using Kompsat-5 image. The accuracy analysis indicates that the proposed WBTI method is less affected by the choice of threshold value and successfully maintains high overall accuracy and Kappa coefficient in wide threshold range.

• 소성∙가공
• /
• 제22권6호
• /
• pp.317-322
• /
• 2013

A radio frequency(R/F) switch connector is widely used in wireless devices such as mobile phone and navigator to check defects of the circuit board of product. The R/F switch connector shell plays a role in protecting the switch connector. Previously, this part was machined using a turning, which is time-consuming and has poor material utilization. Furthermore, the workpiece material of brass containing lead that has excellent machinability has environmentally regulated during recent years. The purpose of the current study was to develop the connector shell by forming through progressive dies including embossing, burring and forging process in order to achieve higher productivity and dimensional accuracy without tool failure. To accomplish this objective, a strip layout was designed and finite element (FE) analysis was performed for each step in the process. Try-out for the connector shell was conducted using progressive die design based on FE-analysis results. Dimensional accuracy of developed part was investigated by scanning electron microscopy. The result of the investigation for the dimensions of the formed connector shell showed that the required dimensional accuracy was satisfied. Moreover, productivity using the progressive die increased four times compared to previous machining process.