• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.288-289
• /
• 2005

As high temperature superconductor applications became a reality due to increase in coated conductor performance, it is important to understand their stability behavior to design safe electrical power systems. We have experimentally studied the dependence of quench and recovery characteristics of coated conductors on the amplitude of current and duration time. The sample used in the present study is stabilized with stainless steel. Stability tests of 3 cm long sample were performed in a liquid nitrogen bath cooling condition by applying a short period over current pulses for 50 and 100 ms, with amplitude up to ~ 6 times of the critical current. The transport current that follows before and after the current pulse was fixed about ~85% the critical current. We analyzed the quench recovery using the current voltage characteristic.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.587-588
• /
• 2005

Ozone is useful oxidizing gas for the fabrication of BSCCO thin films. In order to obtain high quality oxide BSCCO thin films, higher ozone concentration is necessary. The growth rates of the films was set in the region from 0.17 to 0.27 nm/min. MgO(100) was used as a substrate. In this paper oxidation property was evaluated relation between oxide gas pressure and inverse temperature(CuO reaction). The obtained condition was formulated by the fabrication of Cu metal thin film by co-deposition using the Ion Beam Sputtering method. Because the CuO phase peak appeared at the XRD evaluation of the CuO thin film using ozone gas, this study has succeeded in the fabrication of the CuO phase at $825^{\circ}C$.

• 한국전기전자재료학회논문지
• /
• 제22권2호
• /
• pp.174-177
• /
• 2009

In this paper, an oscillator using dielectric-rod loaded cavity resonators with HTS(High Temperature Superconductor) end-plates was presented. It was operated at X-band. A two port cavity resonator was incorporated into a basic feedback loop oscillator configuration. A rutile loaded cavity resonator with HTS thin film end-plates was used to provide the quality factor between $10^4$ and $10^6$. A parallel feedback oscillator was constructed with a dielectric loaded cavity resonator, an amplifier, and a directional coupler. At 300 K, the experimental results showed the phase noise of -108 dBc/Hz at a 100 kHz offset frequency. At 26 K, the results was -118.8 dBc/Hz at same offset frequency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전력기술부문
• /
• pp.240-242
• /
• 2004

Maximum short circuit current of modern power system is becoming so large that the current should transmission capability. Although there are various kinds of method to solve this, approached from super conductivity Fault Current Limiter application viewpoint among them. High Temperature Superconductor-Fault Current Limiter (HTS-FCL) development is progressing according to HTS technology development, and system application is tried. For actual system application of such super conductivity FCL, an more efficient method was developed to find suitable FCL application locations using sensitivity factor comparing previous paper.

• 한국자기학회지
• /
• 제4권1호
• /
• pp.48-51
• /
• 1994

$^{63}Cu$ 핵사중극공명을 이용하여 자기적으로 정렬된 $YBa_{2}Cu_{3}O_{7}$ 고온초전도체 시료의 비등방성을 조사하였다. 정렬된 시료에서는 RF 자기장이 c-축에 수직으로 가해질 때만 공명신호가 검출되었다. 자기적으로 정렬된 시료와 정렬되지 않은 시료로부터 측정된 공명차이로부터 $YBa_{2}Cu_{3}O_{7}$의 자기적 비등방성을 관측할 수 있었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제21권2호
• /
• pp.45-49
• /
• 2019

This paper reports comparison between analytic and numerical simulation approaches for calculation of screening current and screening current induced field in a high temperature superconductor magnet. Bean slab model is adopted to calculate screening current and SCF analytically, while the finite element method numerically. A case study of screening current and SCF calculation are conducted with a magnet, a 7 T 68 mm cold-bore multi-width no-insulation GdBCO magnet built and tested by Massachusetts Institute of Technology Francis Bitter Magnet Laboratory. In this study, we assume the magnet is dunked in liquid nitrogen at 77 K. Furthermore, the simulation results are compared in terms of computation time and accuracy. Finally, discussion on the different methods together with the comparison between the calculations and experiment is provided.

• 한국초전도ㆍ저온공학회논문지
• /
• 제10권1호
• /
• pp.62-66
• /
• 2008

The characteristic of the superconducting magnetic energy storage(SMES) system is faster response, longer life time, more economical, and environment friendly than other uninterruptible power supply(UPS) using battery. So, the SMES system can be used to develop methods for improving power quality where a short interruption of power could lead to a long and costly shutdown. Recently, cryogen free SMES has developed using BSCCO(Bismuth Strontium Calcium Copper Oxide) wire. We fabricated and tested the conduction cooling system for the 600 kJ class HTS SMES. The experiment was accomplished for the simulation coils. The simulation coils were made of aluminium, it is equivalent to thermal mass of 600 kJ HTS SMES coil. The coil is cooled with two GM coolers through the copper conduction bar. In this paper, we report that the test results of cool-down and heat loads characteristics of the simulation coils. The developed conduction cooling system adapted to 600 kJ HTS SMES system and cope with the unexpected sudden heat impact, too.

• 한국전기전자재료학회논문지
• /
• 제11권2호
• /
• pp.154-161
• /
• 1998

The effects of melting temperature and holding time on the critical current density($J_c$) of $YBa_2Cu_3O_x$ based superconducting bulk fabricated by MPMG process were investigated. The amount of the formed $Y_2BaCuO_5$ phases increased with the melting temperature. However, the value of critical current density was highest at 1120 $^{\circ}C$. With this proper melting temperature, the effect of holding time on the critical characteristics was also investigated. In the case of Ag addition, the volume of the formed $Y_2BaCuO_5$ phase when the amount of Ag addition was 10 wt% and 20 wt% was observed to be highest at 20 minute and 40 minute respectively. But in the specimen without Ag, volume of $Y_2BaCuO_5$ phase increased as the holding time increased. The proper melting temperature and the holding time obtained were 1120 $^{\circ}C$ and 20 minute. The long holding time was not effective for the $J_c$ improvement as well as the formation of $Y_2BaCuO_5$.

• 한국산업정보학회논문지
• /
• 제24권1호
• /
• pp.39-44
• /
• 2019

고온 초전도 (HTS) 발전기는 무게, 크기 및 효율의 장점 때문에 활발히 연구되어왔다. 대규모의 초전도 풍력 발전기는 매우 저속의 고토크 회전 기계이다. 이 기계에서는 높은 전자기력과 토크가 중요한 문제이다. 하나의 축에 직렬로 연결된 2개의 발전기는 고토크의 문제를 극복하기위한 하나의 해결 방안이 될 수 있다. 본 논문에서 저자는 15 MW 급 HTS 발전기를 설계하고 분석했다. 3D 유한 요소법을 사용하여 15 MW HTS 발전기의 자기장 분포 및 토크 성능을 확인하였다. 결과적으로 설계된 발전기는 기존의 발전기보다 적은 토크를 생성한다. 제시된 15 MW 초전도 발전기의 설계방식은 대용량 초전도 풍력 발전기의 제작에 있어 고토크로 인한 문제를 해결하는데 활용될 수 있다.

• KEPCO Journal on Electric Power and Energy
• /
• 제6권4호
• /
• pp.467-472
• /
• 2020

The superconducting synchronous generator is one of the breakthrough elements for direct-drive wind turbines because it is light and small. Normally the superconducting one has copper armature windings in the stator and superconducting field windings on the rotor. The high resistance of the armature can make large copper losses, comparing with the conventional generators with a gear box. One of the solutions for the large copper losses could be a fully superconducting generator. But the high magnetic fields from the superconducting field windings on the rotor also make high perpendicular magnetic fields on the superconducting tapes in the armature windings. We have proposed a fully superconducting synchronous generator with dual field windings. It could immensely decrease the circumferential component of the magnetic field from the field windings at the armature windings. In this paper, we conceptually designed 3 types of superconducting synchronous generators. The first one is the fully superconducting one with conventional structure, which has superconducting armature windings in the stator and superconducting field windings on the rotor. The second one is the one with dual superconducting field windings and superconducting armature windings between them. The last one is the same as the third one except the structure of the armature. If the concentrated armature windings are superconducting ones with cryostats, then they cannot be installed within the span of 2 poles. So, we adopted 3 phases windings within 4 poles system. It makes more AC losses but can be manufactured really.