• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1994년도 춘계학술대회 논문집
• /
• pp.30-33
• /
• 1994

This paper studies on the effect of DSC(Differential Scanning Calorimeter) analysis condition on the glass transition temperature of silica filled epoxy network polymer used for ultra-high voltage apparatus. The effects of temperature scanning rate specimen size and gas flow rate on measured glass transition temperature have been studied in order to select optimum thermal analysis condition.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제28회 KOSCO SYMPOSIUM 논문집
• /
• pp.192-198
• /
• 2004

A numerical study was conducted to determine the effects of high temperature air, including equivalent ratio on flow field, temperature, evaporation, and overall temperature distribution in gas turbine combustor. A sector model of a typical wall jet can combustor, featuring introduction of primary air and dilution air via wall jet, was used in calculations. Flow field and temperature distribution were analyzed. Operating conditions such as inlet temperature and overall equivalent ratio were varied from 373 to 1300 K, and from 0.3 to 0.6, respectively, while any other operating conditions were fixed. The RNG ${\kappa}-{\varepsilon}$ model and eddy breakup model were used for turbulence and combustion model respectively. It was found that the increase with the inlet air temperature, velocity in the combustor is accelerated and evaporation of liquid fuel is not affected in primary zone, high temperature inlet air enhances the evaporation and improves overall temperature distribution factor.

• Journal of Applied Biological Chemistry
• /
• 제43권3호
• /
• pp.161-164
• /
• 2000

The effects of storage temperature and high relative humidity (RH) on the weight loss, color change, and microbial activity of a mushroom ('Sylvan' hybrid white) were investigated. The experiment was performed at three temperature (5, 10 and $15^{\circ}C$) and four different relative humidity levels (91, 94, 97 and 99%). The weight loss of the tested samples had a highly correlated linear relationship with storage time at each RH level during storage. Both the storage temperature and RH levels in the experiment had signigicant effects (p<0.05) on the weight-loss rate of the tested samples. The loss whiteness of mushrooms was not significantly affected (p>0.05) by RH ranges at the same temperature. No visible damage was caused by either bacteria or fungi in all samples during storage.

• 한국작물학회지
• /
• 제15권
• /
• pp.1-31
• /
• 1974

소맥의 조숙품종육성을 위하여는 춘파성품종의 조숙인자를 추파성품종에 도입하는 것이 중요한 과제이므로 춘추파성 소맥품종의 일장과 온도조건에 따른 출수반응 및 출수기를 지배하는 생리적 요인의 구명과 출수기의 유전에 관한 지견을 얻고저 본실험을 실시하였다. 수원 작물시험장 전작포장 및 온실에서 1970년부터 조숙품종 Yecora F70, 중숙품종 수계 169호, 육성 003 만숙품종 장광, Bezostaia, Sturdy, Blueboy 등 8개품종을 상호교배하여 1972년부터 1973년에 온실 및 초자실을 이용하여 양친과 Diallel cross F$_1$을 고온장일, 고온단일, 저온장일, 저온단일의 4처리조건 및 포장조건에서 3조합의 F$_1$, F$_2$, BC$_1$, BC$_2$ 및 양친들은 고온단일조건에서 F$_1$, F$_2$ 9조합 및 그 양친은 포장에서 각각 재배 실험하였다. 그 결과를 요약하면 다음과 같다. 1. 춘화 처리후의 주요엽수는 일장 및 온도조건에 관계없이 일정하였으나 주간의 출엽속도에만 영향을 주었으며 춘파성품종은 추파성품종보다 주간엽수가 적었다. 2. 지엽전개일수의 일장 및 온도반응은 출수속도에 의하여 결정되며 일장과 온도에 따른 출엽속도의 차이는 하위엽보다 상위엽에서 컸다. 3. 춘화처리후의 출수기에 대한 생리적 요인은 일장반응과 순수조만생이며, 출수일수의 품종간 변이는 고온단일에서 가장 크고 포장조건에서 가장 적었으며 고온장일, 저온장일, 저온단일을 비슷하였다. 4. 일장차이에 의한 출수일수의 품종간 반응은 장광, Parker가 크고, Yecora F70, 수계 169 호 등 기타 품종들은 비교적 적었으며, 장광, Parker는 단일이 의하여 출수일수가 크게 지연되는 감광성 품종이었다. 5. 일장반응은 온도의 영향을 크게 받고 출수일수의 품종간차이는 저온일 빼보다 고온일 때 현저히 나타났다. 6. 온도차이에 의한 출수일수의 품종간 반응은 비슷하였으며, 어떠한 품종이라도 고온에 의하여 출수가 촉진되고 저온에 의해서 지연되었다.7. 출수일수에 대한 유전은 일장 및 온도조건이 변하여도 조숙은 만숙에 대하여 부분우성이었으며, 우성의 정도는 단일에서 크고 장일에서 적었다. 8. 고온장일조건에서 출수일수의 품종간 차이는 수수조만성의 차이라고 할 수 있으며, 춘파성품종인 Yecora F70은 추파성품종에 대하여 우성정도가 컸고 추파성품종간에는 우성정도가 없거나 적었다. 이때의 유효 우성 유전자수는 1쌍의 대립유전자에 의해서 지배되나 다소의 미동유전자가 관여되었다. 9. 출수일수에 관여하는 비감광성은 감광성에 대하여 우성단인자차에 의하여 지배되었고 저온조건에서는 단일감응성의 발현정도가 둔화 또는 억제되었다. 10. 순수 조만성과 단일감응성은 모두 조숙이 만숙에 대하여 부분우성으로 표현되었다. 11. 출수기에 관여하는 감온성의 품종간반응은 대립유전자 및 비대립유전자의 지배를 받으며 같은 대립유전자를 가진 품종군에서는 비감온성이 감온성에 대하여 우성으로 표현되나 일장 및 순수 조만성보다는 그 정도가 미미하다. 12. 장광과 수계 169호 사이에는 감광성에 관여하는 1쌍의 대립인자 ee와 EE에 의하여 조만이 결정되었고, 장광과 Yecora F70사이에는 ee, enen과 EE, EnEn의 2쌍의 대립인자에 의하여 지배된다고 추정되었다. 이때 EE와 EnEn는 조숙방향에 상가적으로 작용하여 단일조건하에서는 EE의 효과가 EnEn의 효과보다 크다. 장일 조건하에서는 EE의 효과는 나타나지 않고 EnEn효과만 발현된다. En과 en 사이에 우열관계는 E와 e 사이보다 적고 상가적 작용을 하고 있다고 본다. 13. 본 실험의 포장조건에서는 2개정도의 우성주동유전자를 가정할 수 있으나 생육초기의 저온단일과 생육후기의 고온장일의 영향으로 2개의 우성유전자 표현이 불확실하며 F$_2$분리에 있어서는 일장 및 온도의 영향과 미동유전자의 영향으로 연속변이를 하였다. 14. 출수일수의 유전력은 0.51-0.72로서 어느 조건에서나 높은 경향으로 초기세대의 선발효과가 큰 것으로 인정되었으며, 환경에 의하여 다소의 차이가 있어 장일보다는 단일에서 유전력이 컸고, 저온보다는 고온에서 큰 경향이었다. 또한 감광성의 유전력은 0.86-0.76으로 컸으나 온도효과의 유전력은 적었다. 15. 출수기가 빨라지므로서 1수입수, 천입중, 수량이 낮아지는 상관관계를 보여 조숙다수성 품종선발이 어렵다는 결과를 보였으나 수수와는 부의 상관(유의성은 없음)을 보여 조숙품종으로서 수수형 품종을 선발하면 수량을 올릴수 있는 약간의 가능성도 보였다.

• Journal of Mechanical Science and Technology
• /
• 제20권12호
• /
• pp.2061-2078
• /
• 2006

The main purpose of this paper is to establish the high temperature structural integrity evaluating procedures for the next generation reactors, which are to be operated at over 500$^{\circ}C$ and for 60 years. To do this, comparison studies of the high temperature structural design codes and assessment procedures such as the ASME-NH (USA), RCC-MR (France), DDS (Japan), and R5 (UK) are carried out in view of the accumulated inelastic strain and the creep-fatigue damage evaluations. Also the application procedures of the ASME-NH rules with the actual thermal and structural analysis results are described in detail. To overcome the complexity and the engineering costs arising from a real application of the ASME-NH rules by hand, all the procedures established in this study such as the time-dependent primary stress limits, total accumulated creep ratcheting strain limits, and the creep-fatigue damage limits are computerized and implemented into the SIE ASME-NH program. Using this program, the selected high temperature structures subjected to two cycle types are evaluated and the parametric studies for the effects of the time step size, primary load, number of cycles, normal temperature for the creep damage evaluations and the effects of the load history on the creep ratcheting strain calculations are investigated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.61-64
• /
• 1998

We have investigated the effects of ultraviolet (UV) light irradiation condition and imidization temperature for the generation of pretilt angle in nematic liquid crystal (NLC) on the two kinds of the polyimide (PI) surfaces. High pretilt angle of NLC is generated with oblique p-polarized UV light irradiation of 30$^{\circ}$ on PI surface for 20 min. Also, the high pretilt angle of NLC is generated with oblique p-polarized UV light irradiation of 10-30$^{\circ}$ on PI surface at 20min. The pretilt angle of NLC decreases with increasing the imidization temperature on all rubbed PI surfaces ; the pretilt angle of NLC with oblique p-polarized UV light irradiation of 30$^{\circ}$on PI surface decreases with increasing the imidization temperature. The high pretilt angle of NLC is observed due to high photo-depolymerization reaction by low surface energy at low imidization temperature. We suggest that the pretilt angle of NLC is strongly attributed to the photo-depolymerization reaction with the UV light irradiation condition and imidization temperature.

• 설비공학논문집
• /
• 제13권3호
• /
• pp.194-199
• /
• 2001

The turbulent flow resistance of water solution with polymer is reduced as compared with that of pure water. This effects is named th drag reduction and offers the significant reduction of the pumping power and the energy consumption. But the intense shear forces and the high temperature experienced by the polymer solution when passing through the pipes cause the degradation a loss of drag reduction effectiveness. Especially, the degradation behavior is found to be strongly dependent on temperature. This mechanical and thermal degradation can be avoided by adding materials such as surfactant to the polymer solution, which enhance the bonding force between molecules. In the present study, Copolymer and SDS were utilized and they were mixed in 10 different mixture ratios, while total concentration was fixed as 100wppm. Degradation of Copolymer-SDS mixture solutions was investigated experimentally in closed loop at the temperature of $10^{\circ}C\; and\; 80^{\circ}C$ with various flow average velocities of 1.5 m/sec, 3.0m/sec, and 4.5m/sec. Degradation characteristics of polymer solution without surfactant show a radical loss of drag reduction effectiveness at high temperature. Degradation alleviation ability of surfactant is especially effective at high temperature. Consequently, this results show that the addition of surfactant to the polymer solution can control unfavorable degradation phenomena for high temperature systems.

• Journal of Ginseng Research
• /
• 제4권1호
• /
• pp.104-120
• /
• 1980

The effects of temperature on transpiration, chlorophyll content, frequency and aperture of stomata, and leaf temperature of Panax ginseng were reviewed. Temperature changes of soil and air under spade roof were also reviewed. Growth responses of responses of ginseng plant at various temperature were assessed in relation to suseptibillity of ginseng plants. Reasonable management of ginseng fields was suggested based on the response of ginseng to various temperatures. Stomata frequency may be increased under high temperature during leaf$.$growing stage. Stomata aperture increased by high temperature but the increase of both frequency and aperture appears not enough for transpiration to overcome high temperature encountered during summer in most fields. Serial high temperature disorder, i.e high leaf temperature, chlorophyll loss, inhibition of photosynthesis, increased respiration and wilting might be alleviated by high humidity and abundant water supply to leaf. High air temperature which limits light transmission rate inside the shade roof, induces high soil temperature(optimum soil temperature 16∼18$^{\circ}C$) and both(especially the latter) are the principal factors to increase alternaria blight, anthracnose, early leaf fall, root rot and high missing rate of plant resulting in poor yield. High temperature disorder was lessen by abundant soil water(optimum 17∼21%) and could be decreased by lowering the content of availability of phosphorus and nitrogen in soil consequently resulting in less activity of microorganisms. Repeated plowing of fields during preparation seems to be effective for sterilization of pathogenic microoganisms by high soil temperature only on surface of soils. Low temperature damage appeared at thowing of soils and emergence stage of ginseng but reports were limited. Most limiting factor of yield appeared as physiological disorder and high pathogen activity due to high temperature during summer(about three months).

• 한국표면공학회지
• /
• 제46권6호
• /
• pp.264-270
• /
• 2013

Effects of preoxidation on high temperature wear of piercing plug tool steel sliding against SA210C steel used for production of seamless tube have been studied using a pin-on-disc CETR tribometer, under applied normal load of 20 N at $900^{\circ}C$ in air. It was found in the preoxidized pin specimens of piercing plug tool steel that the coefficient of friction decreased to about 0.4 at an initial stage followed by showing nearly constant value of about 0.4 during high temperature wear testing. On the other hand, it was also found in the pin specimens without preoxidation that the coefficient of friction increased and fluctuated, ranging from about 0.3 to 0.6 during the tests until the running period of about 800 sec. The compact and continuous Fe-oxide layer was formed on the contact surface of the preoxidized pin specimens after high temperature wear testing followed by penetrating along the grain boundaries of coarse ferrite in the decarburized region beneath the oxide layer due to the lower hardness of the region.

• 한국안전학회지
• /
• 제18권2호
• /
• pp.34-39
• /
• 2003

In this paper, when CF/PEEK laminates for high efficiency space structure are subjected to FOD(Foreign Object Damage), the effects of temperature change on the impact damages(interlaminar separation and transverse crack) of CF/PEEK laminates and the relationship between residual lift and impact damages are experimentally investigated. Composite laminates used in this experiment are CF/PEEK orthotropic laminated plates, which have two-interlaces [$0^{\circ}_4/90^{\circ}_8/0^{\circ}_4$]. A steel ball launched by the air gun collides against CF/PEEK laminates to generate impact damages. And then CF/PEEK specimens with impact damages are observed by a scanning acoustic microscope under room and high temperatures. In this experimental results, various relations are experimentally observed including the delamination area vs. temperature change, the bending strength vs. impact energy and the residual bending strength vs. impact damage of CF/PEEK laminates.