• Korean Journal of Food Science and Technology
• /
• v.34 no.5
• /
• pp.846-855
• /
• 2002

Several soft white spring and winter wheat cultivars were evaluated by analyzing physicochemical properties such as Single Kernel Characterization System (SKCS), milling properties, Rapid Visco-Analyzer (RVA), mixograph pattern, and sugar-snap cookie-making potentialities. Results of SKCS revealed kernel hardness had a positive correlation coefficient with test weight $(r=0.497^{*})$ and near-infrared reflectance (NIR) hardness $(r=0.495^{*})$. SKCS kernel weight had a significantly high correlation of $r=0.942^{**}$ with SKCS kernel size. The test weight had significantly high correlations with straight-grade flour yield $(r=0.720^{**})$, break flour yield $(r=0.490^{*})$, flour ash content $(r=-0.781^{**})$, and milling score $(r=0.838^{**})$. The average RVA peak viscosity of the soft white winter wheat was higher (195.1 unit) than the soft white winter wheat varieties (135.7 unit). A correlation was found between RVA peak viscosity and swelling volume. Significant correlation coefficients were obtained among cookie properties, milling properties, protein content, and mixograph absorption. The cookie top grain score had a correlation coefficient of $r=0.447^{*}$ with swelling volume.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.24 no.1
• /
• pp.37-45
• /
• 1979

Experiments were conducted to determine the physicochemical properties for 1.382 tested wheat harvested in 1977. All the tested wheats had a milling yield rate of 49 to 71.5 percent. The cross combination involving S.son, Caprock and CI 12703 was generally the higher in flour yield-Flour protein content ranged from about 7 percent up to about 17 percent and sedimentation values ranged from below 20 cc to 70 cc. The cross combinations involving Bb #1 gave higher protein content and higher sedimentation values than the other combinations. The distribution of the Pelshenke value was from less 20 min. to more than 180 min. Specific sedimentation values of the 329 tested wheats showed 8.1 percent to be hard quality, while 54.4 percent were of soft quality. Intermediate wheats accounted for 37.5 percent. The lines having high milling yield rate, protein content and sedimentation value from the 329 tested wheats were Strampelli \times 69D-3607/Jogwang. S.son \times Caprock. Suweon #185 \times Toropi and Suweon #185 \times Ciano. The varieties or lines including Pribog, CI 14496 and Sturdy \times Scout/ Strampelli \times Bb-Cno showed high milling yield but low protein content and low sedimentation values. being under 9 percent and 30 cc respectively.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.953-954
• /
• 2006

Ti-Cu-Ni-Sn quaternary amorphous alloys of $Ti_{50}Cu_{32}Ni_{15}Sn_3$, $Ti_{50}Cu_{25}Ni_{20}Sn_5$, and $Ti_{50}Cu_{23}Ni_{20}Sn_7$ composition were prepared by mechanical alloying in a planetary high-energy ball-mill (AGO-2). The amorphization of all three alloys was found to set in after milling at 300rpm speed for 2h. A complete amorphization was observed for $Ti_{50}Cu_{32}Ni_{15}Sn_3$ and $Ti_{50}Cu_{25}Ni_{20}Sn_5$ after 30h and 20h of milling, respectively. Differential scanning calorimetry analyses revealed that the thermal stability increased in the order of $Ti_{50}Cu_{32}Ni_{15}Sn_3$, $Ti_{50}Cu_{25}Ni_{20}Sn_5$, and $Ti_{50}Cu_{23}Ni_{20}Sn_7$.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.956-961
• /
• 2003

Recently, environmental pollution has become a significant problem in industry and many researches have been investigated in order to preserve the environment. Environmentally conscious machining and technology have more and more important position in machining process. In the milling process, the cutting fluid has greatly bad influence on the environment. In this study, the machining of blade parts(12Cr steel) using the cutting fluid, compressed cold air and oil mist etc., also, the productivity and the surface topography was improved by using new end-mil tool considering tool material and shape.

• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.941-946
• /
• 2018

Currently, due to the development of technology, the industry is proceeding with the development of advanced materials with high performance such as light weight, heat resistance and electric conductivity. Carbon Fiber Reinforced Plastics (CFRP) is an excellent material with high heat resistance, high strength and thermal shock resistance. In order to obtain excellent hole shape in CFRP drilling, we compared the modified drill shape and the conventional carbide drill. On the other hand, we determine the proper helix angle by observing the CFRP surface according to the helix angle at the trimming of the end mill proceeding after the hole machining.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.975-976
• /
• 2006

The present paper is a parameter study of zinc flake production using a Simoloyer CM01 horizontal high energy rotary ball mill. The manufactured flakes have a dimension in thickness (t) < $1{\mu}m$ and diameters (d) 5-100 ${\mu}m$, consequently a ratio d/t up to 200. The flake geometry is mainly controlled by the variation of process parameters such as rotary speed of the rotor, ratio of powder/ball charge, load ratio of the system, process temperature, operating model and the quantity of process control agent (PCA). The Zn flakes were characterized by SEM, tap densitometry, laser diffraction and water coverage measurement.

• Applied Microscopy
• /
• v.45 no.4
• /
• pp.195-198
• /
• 2015

Gas-assisted etching (GAE) with focused ion beam (FIB) was applied to prepare plan-view specimens of Cu thin-layer on a silicon substrate for transmission electron microscopy (TEM). GAE using $XeF_2$ gas selectively etched the silicon substrate without volume loss of the Cu thin-layer. The plan-view specimen of the Cu thin film prepared by FIB milling with GAE was observed by scanning electron microscopy and $C_S$-corrected high-resolution TEM to estimate the size and microstructure of the TEM specimen. The GAE with FIB technique overcame various artifacts of conventional FIB milling technique such as bending, shrinking and non-uniform thickness of the TEM specimens. The Cu thin film was uniform in thickness and relatively larger in size despite of the thickness of <200 nm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.225-226
• /
• 2006

As the technique of high-speed end-milling is widely adopted to machining field. The investigation for microscopic precision of workpiece is necessary for machinability evolution. The environmental pollution has become a big problem in industry and many researcher have investigated in order to preserve the environment. The environmentally conscious machining and technology have more important position in machining process. In the milling process, the cutting fluid has greatly bad influence on the environment. The damaged layer affect mold life and machine parts in machining. In this study, the cutting force, the surface roughness, micro hardness and residual stress is evaluated according to machining environment. Finally, it is obtained that the characteristics of damaged layer in environmentally conscious machining is better than that in conventional machining using cutting fluid.

• Journal of Powder Materials
• /
• v.20 no.3
• /
• pp.221-227
• /
• 2013

$TiB_2$-reinforced iron matrix composite (Fe-$TiB_2$) powder was in-situ fabricated from titanium hydride ($TiH_2$) and iron boride (FeB) powders by the mechanical activation and a subsequent reaction. Phase formation of the composite powder was identified by X-ray diffraction (XRD). The morphology and phase composition were observed and measured by field emission-scanning electron microscopy (FE-SEM) and energy-dispersive X-ray spectroscopy (EDS), respectively. The results showed that $TiB_2$ particles formed in nanoscale were uniformly distributed in Fe matrix. $Fe_2B$ phase existed due to an incomplete reaction of Ti and FeB. Effect of milling process and synthesis temperature on the formation of composite were discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05b
• /
• pp.120-124
• /
• 2004

The protection performance and energy absorption capability are important for both MOAs for distribution lines and MOAs for high voltage systems, therefore the manufacturing technique of ZnO varistor elements with high ability against surge impacts is great important for high voltage systems. But until now ZnO varistors for low voltage class have been developed in Korea, ZnO varistors with the rate discharge current of 5, 10kA class for high voltage systems depend on an import from advanced countries, such as Japan or U.S.A, which have developed its in the late 1980s. So in the aspect of taking independent technique the development of ZnO varistors with the rate discharge current of 5, 10kA class for high voltage systems is important. In this research project ZnO varistor elements with diameters of 35mm and 70mm for the rate discharge current of 5, 10kA class for high voltage systems are manufactured, then various chemical composition and processing variables affected the electrical and the physical characteristics of these ZnO varistors are investigated.