• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.264-264
• /
• 2010

Single-walled carbon nanotubes (SWCNTs) were grown on a Si wafer by using thermal chemical vapor deposition (t-CVD). We investigated the effect of the catalyst deposition rate on the types of CNTs grown on the substrate. In general, smaller islands of catalyst occur by agglomeration of a catalyst layer upon annealing as the catalyst layer becomes thinner, which results in the growth of CNTs with smaller diameters. For the same thickness of catalyst, a slower deposition rate will cause a more uniformly thin catalyst layer, which will be agglomerated during annealing, producing smaller catalyst islands. Thus, we can expect that the smaller-diameter CNTs will grow on the catalyst deposited with a lower rate even for the same thickness of catalyst. The 0.5-nm-thick Fe served as a catalyst, underneath which Al was coated as a catalyst support as well as a diffusion barrier on the Si substrate. The catalyst layers were. coated by using thermal evaporation. The deposition rates of the Al and Fe layers varied to be 90, 180 sec/nm and 70, 140 sec/nm, respectively. We prepared the four different combinations of the deposition rates of the AI and Fe layers. CNTs were synthesized for 10 min by flowing 60 sccm of Ar and 60 sccm of $H_2$ as a carrier gas and 20 sccm of $C_2H_2$ as a feedstock at 95 torr and $810^{\circ}C$. The substrates were subject to annealing for 20 sec for every case to form small catalyst islands prior to CNT growth. As-grown CNTs were characterized by using field emission scanning electron microscopy, high resolution transmission electron microscopy, Raman spectroscopy, UV-Vis NIR spectroscopy, and atomic force microscopy. The fast deposition of both the Al and Fe layers gave rise to the growth of thin multiwalled CNTs with the height of ${\sim}680\;{\mu}m$ for 10 min while the slow deposition caused the growth of ${\sim}800\;{\mu}m$ high SWCNTs. Several radial breathing mode (RBM) peaks in the Raman spectra were observed at the Raman shifts of $113.3{\sim}281.3\;cm^{-1}$, implying the presence of SWCNTs (or double-walled CNTs) with the tube diameters 2.07~0.83 nm. The Raman spectra of the as-grown SWCNTs showed very low G/D peak intensity ratios, indicating their low defect concentrations.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.463-463
• /
• 2014

Dye-sensitized solar cells (DSSCs) have generated a strong interest in the development of solid-state devices owing to their low cost and simple preparation procedures. Effort has been devoted to the study of electrolytes that allow light-to-electrical power conversion for DSSC applications. Several attempts have been made to substitute the liquid electrolyte in the original solar cells by using (2,2',7,7'-tetrakis (N,N-di-p-methoxyphenylamine)-9-9'-spirobi-fluorene (spiro-OMeTAD) that act as hole conductor [1]. Although efficiencies above 3% have been reached by several groups, here the major challenging is limited photoelectrode thickness ($2{\mu}m$), which is very low due to electron diffusion length (Ln) for spiro-OMeTAD ($4.4{\mu}m$) [2]. In principle, the $TiO_2$ layer can be thicker than had been thought previously. This has important implications for the design of high-efficiency solid-state DSSCs. In the present study, we have fabricated 3-D Transparent Conducting Oxide (TCO) by growing tin-doped indium oxide (ITO) nanowire (NWs) arrays via a vapor transport method [3] and mesoporous $TiO_2$ nanoparticle (NP)-based photoelectrodes were prepared using doctor blade method. Finally optimized light-harvesting solid-state DSSCs is made using 3-D TCO where electron life time is controlled the recombination rate through fast charge collection and also ITO NWs length can be controlled in the range of over $2{\mu}m$ and has been characterized using field emission scanning electron microscopy (FE-SEM). Structural analyses by high-resolution transmission electron microscopy (HRTEM) and X-Ray diffraction (XRD) results reveal that the ITO NWs formed single crystal oriented [100] direction. Also to compare the charge collection properties of conventional NPs based solid-state DSSCs with ITO NWs based solid-state DSSCs, we have studied intensity modulated photovoltage spectroscopy (IMVS), intensity modulated photocurrent spectroscopy (IMPS) and transient open circuit voltages. As a result, above $4{\mu}m$ thick ITO NWs based photoelectrodes with Z907 dye shown the best performing device, exhibiting a short-circuit current density of 7.21 mA cm-2 under simulated solar emission of 100 mW cm-2 associated with an overall power conversion efficiency of 2.80 %. Finally, we achieved the efficiency of 7.5% by applying a CH3NH3PbI3 perovskite sensitizer.

• Korean Journal of Materials Research
• /
• v.13 no.8
• /
• pp.497-502
• /
• 2003

Crystallographic characteristics and interfacial structures of $Al_2$$O_3$and $ZrO_2$dielectric films prepared by atomic layer chemical vapor deposition (ALCVD) were investigated at atomic scale by high-resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray spectroscopy (EDS)/electron energy-loss spectroscopy (EELS) coupled with a field-emission transmission electron microscope. The results obtained from cross-sectional and plan-view specimens showed that the $Al_2$$O_3$film was crystallized by annealing at a high temperature and its crystal system might be evaluated as either cubic or tetragonal phase. Whereas the $ZrO_2$film crystallized during deposition at a low temperature of ∼$300^{\circ}C$ was composed of both tetragonal and monoclinic phase. The interfacial thickness in both films was increased with the increased annealing temperature. Further, the interfacial structures of X$ZrO_2$$O_3$and $ZrO_2$films were discussed through analyses of EDS elemental maps and EELS spectra obtained from the annealed films, respectively.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.890-893
• /
• 2012

Gas hydrates are solid crystal structures formed by enclathration of gaseous guest species into 3-dimensional lattice structure of hydrogen-bonded water molecules. These compounds can be potentially used as an energy storage/transportation medium because they can hold a large amount of gas in a small volume of the solid phase. In addition, huge amount of natural gas, buried in seabeds or permafrost region in the form of the solid hydrate, is regarded as a future energy source. In this study, synthesized natural gas, whose composition is 90.0 mol% of methane, 7.0 mol% of ethane, and 3.0 mol% of propane, was used to identify formation behaviors of natural gas hydrates for the purpose of applying the gas hydrate to a storage/transportation medium of natural gas. According to the experimental results obtained by means of the solid-state NMR and high-resolution powder XRD methods, it is found that formed natural gas hydrates have crystal structure of the structure-II hydrate, and that methane occupies both small and large cages, while the others only occupy large ones. In addition, both the NMR spectroscopy and the gas chromatograph showed that there exists preferential occupation among the natural gas components during the hydrate formation. Compositional changes after the hydrate formation revealed that the preferential occupation is in order of propane, ethane, and methane (propane is the most preferential guest species when forming natural gas hydrates).

• Journal of Astronomy and Space Sciences
• /
• v.22 no.4
• /
• pp.353-362
• /
• 2005

We performed a new high-resolution spectroscopy of AG Vir for 4 nights from 25 March 2004 using the BOES (Bohyunsan Optical Echelle Spectrograph) attached to the 1.8-m reflector at Bohyunsan Optical Astronomy Observatory, and obtained a total of 59 spectra where all orbital phases are covered. To get the radial velocities of the binary system, both method of the CCF (Cross-Co..elation Function)and the BF (Broadening Function) were applied to the analysis of all the observed spectra. From these, the CCF could calculate the radial velocities of the primary star alone, while the BF could determine those of the primary and the secondary components. New absolute dimensions were deduced with the combination of our spectroscopic orbital elements ($K_1=90.5km/s$와 $K_2=258.8$) and the photometric solutions of Bell, Rainger, & Hilditch (1990): $A_1,=1.99M_\bigodot,\;M_2=0.62M_\bigodot,\;R_1=2.21R_\bigodot,\;R_2=1.36R_\bigodot,\;L_1=13.17L_\bigodot,\;and\;L_2=3.47L_\bigodot$. Our absolute parameters are larger and brighter than those derived from Bell, Rainger, & Hilditch (1990). We re-analyzed all the previous radial-velocity curves of AG Vir and, as a result, can see that its system velocity scatters largely up to ${\pm}8km/s$. However, we, at present, cannot determine this as the light-time effect due to the third body, which was suggested as a cause of the orbital period changes by Qian (2001).

• Journal of the Korean Vacuum Society
• /
• v.16 no.5
• /
• pp.377-382
• /
• 2007

In this study, we report the synthesis of the single-walled carbon nanotubes(SWCNTs) using laminated catalyst(Al/Fe/Al) layer deposited by sputter on Si(001). SWCNTs are grown by thermal chemical vapor deposition (TCVD) method. As the results of scanning electron microscopy(SEM), high resolution transmission electron microscopy(HR-TEM) and Raman spectroscopy, we confirmed the SWCNTs bundles with narrow diameter distribution of $1.14{\sim}1.32\;nm$ and average G&D ratio of 22.76. Compare to the sample having Fe/Al catalyst layer, it can be proposed that the top-aluminum incorporated with iron catalyst plays an important role in growing process of CNTs as a agglomeration barrier of the Fe catalyst. Thus, we suggest that a proper quantity of aluminium metal incorporated in Fe catalyst induce small and uniform iron catalysts causing SWCNTs with narrow diameter distribution.

• Journal of the Korean Vacuum Society
• /
• v.16 no.4
• /
• pp.279-285
• /
• 2007

We have demonstrated structural evolution and optical properties of the Si-NWs on Si (111) substrates with synthesized nanoscale Au-Si islands by rapid thermal chemical vapor deposition(RTCVD). Au nano-islands (10-50nm in diameter) were employed as a liquid-droplet catalysis to grow Si-NWs via vapor-liquid-solid mechanism. Si-NWs were grown by a mixture gas of $SiH_4\;and\;H_2$ at pressures of $0.1{\sim}1.0$Torr and temperatures of $450{\sim}650^{\circ}C$. SEM measurements showed the formation of Si-NWs well-aligned vertically for Si (111) surfaces. The resulting NWs are 30-100nm in diameter and $0.4{\sim}12um$ in length depending on growth conditions. HR-TEM measurements indicated that Si-NWs are single crystals convered with about 3nm thick layers of amorphous oxide. In addition, optical properties of NWs were investigated by micro-Raman spectroscopy. The downshift and asymmetric broadening of the Si optical phonon peak with a shoulder at $480cm^{-1}$ were observed in Raman spectra of Si-NWs.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.11
• /
• pp.1659-1663
• /
• 2003

$Al_2O_3$ thin films were grown on H-terminated Si(001) substrates using dimethylaluminum isopropoxide [DMAl: $(CH_3)_2AlOCH(CH_3)_2$], as a new Al precursor, and water by atomic layer deposition (ALD). The selflimiting ALD process by alternate surface reactions of DMAI and $H_2O$ was confirmed from measured thicknesses of the aluminum oxide films as functions of the DMAI pulse time and the number of DMAI-$H_2O$ cycles. Under optimal reaction conditions, a growth rate of ~1.06 ${\AA}$ per ALD cycle was achieved at the substrate temperature of $150\;^{\circ}C$. From a mass spectrometric study of the DMAI-$D_2O$ ALD process, it was determined that the overall binary reaction for the deposition of $Al_2O_3\;[2\;(CH_3)_2AlOCH(CH_3)_2\;+\;3\;H_2O\;{\rightarrow}\;Al_2O_3\;+\;4\;CH_4\;+\;2\;HOCH(CH_3)_2]$can be separated into the following two half-reactions: where the asterisks designate the surface species. Growth of stoichiometric $Al_2O_3$ thin films with carbon incorporation less than 1.5 atomic % was confirmed by depth profiling Auger electron spectroscopy. Atomic force microscopy images show atomically flat and uniform surfaces. X-ray photoelectron spectroscopy and cross-sectional high resolution transmission electron microscopy of an $Al_2O_3$ film indicate that there is no distinguishable interfacial Si oxide layer except that a very thin layer of aluminum silicate may have been formed between the $Al_2O_3$ film and the Si substrate. C-V measurements of an $Al_2O_3$ film showed capacitance values comparable to previously reported values.

• Journal of Photoscience
• /
• v.9 no.2
• /
• pp.126-129
• /
• 2002

The chromophore/protein interactions in the photocycle intermediates of photoactive yel- low protein (PYP) were probed by site-directed mutagenesis. The absorption spectra of L- intermediates produced from E46Q, T50V, and R52Q mutants were calculated using the absorption spectra of dark states and difference absorption spectra between L-intermediates and dark states, and compared with that of PYP$\_$L/. The absorption spectrum of R52Q$\_$L/ agreed with that of PYP$\_$L/, but those of E46Q$\_$L/ and T50V$\_$L/ were red-shifted. The effect of these mutations on the absorption spectrum for L-intermediate was comparable to that for the dark state, suggesting that the interaction around the phe-nolic oxygen of the chromophore is conserved in PYP$\_$L/ unlike the crystal structure. On the other hand, we have reported that the absorption spectra of Y 42F$\_$M/, T50V $\_$M/, and R52Q$\_$M/ agreed with that of PYP$\_$M/, but that of E46Q$\_$M/ was red-shifted, suggesting that the hydrogen bond of the chromophore with Glu46 is conserved but that with Tyr42 is broken in PYP$\_$M/. These results suggest that the chromophore inter-acts with Glu46 throughout the photocycle, but never directly interacts with Arg52. This model con- flicts with some of the structural model of PYP intermediates proposed based on the high-resolution X -ray crystallography.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.spc8
• /
• pp.3081-3089
• /
• 2011

A series of new bis-thienylanthracene derivatives D1~D5 containing 9,10-antharcene moiety in the center and 2-methylenemalonotitrile or 2-cyanoacrylic acid functional group on the terminal thiophenes were synthesized and characterized by $^1H$-NMR and high-resolution mass spectroscopy. Their optical, electrochemical, and thermal properties were measured. They have absorption ${\lambda}_{max}$ in the range of 437~480 nm and max of $7.4{\times}10^3{\sim}2.0{\times}10^4M^{-1}cm^{-1}$. The substitution of 2-cyanoacrylic acid group allows greater value of ${\varepsilon}_{max}$ than that of 2-methylenemalonotitrile. TGA curves showed that D4 and D5 which have 2-cyanoacrylic acid functional group on the terminal thiophene(s) exhibit good thermal stability and D4 was thermally stable up to $400^{\circ}C$. Their optical properties and LUMO energy levels measured suggest that they can serve as potential candidates for electron donor materials of organic photovoltaic cells (OPVs) or D4 and D5 which contain 2-cyanoacrylic acid group can be used as organic dyes of dye-sensitized solar cells (DSSCs).