• 대한기계학회논문집
• /
• 제16권2호
• /
• pp.191-199
• /
• 1992

This paper presents in experimental study of the dynamic internal pressure within an oil hydraulic vane pump. The measurements of the dynamic internal pressures near the vane of a pressure balance type of an oil hydraulic vane pump with intravanes has been made to provide the essential information for the study of the pump dynamics and control, the pump design and the analysis of tribological problems in the sliding components. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in four chambers surrounding a vane have been investigated. The results indicate that the surge pressures of the chambers at the instant moment of discharge and closure are affected by the rotating speed. The pressure in the intravane chamber maintains almost constant values, which remarkably effects the pulsating discharge pressure.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.228-233
• /
• 2014

Reduction of the atmospheric pressure in high altitude affects brake booster system which was operated by the difference between the intake pressure and the atmospheric pressure. So, braking system can not stably perform due to decrease of brake boost pressure. In this study, effects of altitude change on engine intake pressure was analyzed by prediction model of engine intake pressure which was studied previously. And engine intake pressure was simulated by simulation model in various driving conditions and environmental conditions.

• The Korean Journal of Physiology
• /
• 제28권2호
• /
• pp.191-196
• /
• 1994

Captopril, an inhibitor of angiotensin converting enzyme, is also known to inhibit the degradation of bradykinin. We examined the effects of intracerebroventricular (ICV) captopril on the central pressor response to bradykinin in normotensive, 2-kidney, 1 clip Goldblatt (GHR) and deoxycorticosterone acetate (DOCA)-salt hypertensive rats. Captopril (1 mg) and bradykinin (5 nmol) were administered into the right lateral cerebral ventricle, and blood pressure and heart rate were continuously monitored throughout the experiment. ICV captopril alone did not affect the blood pressure within 10 minutes but it significantly augmented the central pressor response to bradykinin in GHR. On the contrary, captopril was without effect on the pressor response to bradykinin in normotensive and DOCA-salt rats. These findings indicate that endogenous kinins are not critical in regulating arterial pressure in normotensive and DOCA hypertensive rats. However, in GHR, an enhanced activity of the brain kallikrein-kinin system in maintaining the high blood pressure is suggested.

• 오토저널
• /
• 제15권1호
• /
• pp.37-44
• /
• 1993

Fuel injection system is an important tool in the exhaust emission and performance of a diesel engine. Effects of the fuel injection system in diesel combustion was investigated experimentally by measuring the performance and analyzing the combustion phenomena in a D.I. diesel engine. The selected injection parameters were nozzle opening pressure, nozzle projection length, and nozzle spray angle. From the measured results, it is shown that the fuel injection pipe diameter is an effective means to improve engine performance in a middle and high speed range and the 2 stage spring nozzle holder has the advantage of increasing the engine performance due to the initial injection pressure in a low speed range. It has been also shown that increasing nozzle opening pressure resulted in decrease in smoke, but increase in NO$_{x}$ from the engine.e.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.149-155
• /
• 2001

Recently, it is required to design higher stage pressure ratio compressor while maintaining equal adiabatic efficiency. To increase the stage pressure ratio, blade rotational speed or diffusion factor should be increased. In the case of increasing rotational speed, relative speed of flow at blade leading edge is well supersonic. In supersonic blade, total pressure loss is mainly due to shock wave and blade leading edge thickness should be very thin to minimize the shock wave loss. As a result, the blade is like to be week in terms of mechanical strength and the manufacturing cost is very high because NC machining is necessary. It is also one of big hurdle to overcome to make small compressor. In this paper, the effects of blade leading edge to the performance of supersonic blade In terms of total pressure loss. The efficiency of already known method to make thin blade leading edge from the casted blade with rather thick leading edge thickness is also assessed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권3호
• /
• pp.396-402
• /
• 2006

In this study, dynamic characteristics of water hammer pressure in water supply piping system with water hammer arrester has been investigated experimentally to characterize the transient pressure of water hammer in high rise building. Experiments were conducted to verify the absorption effects by water hammer arresters with 3 different gas volumes of water hammer pressure generated by sudden valve closure. As the results, it has been found that zoning and sizing of pipe diameter for suitable flow velocity and water hammer arresters with effective pressure absorption capacity have to be installed to protect water hammer problems in building water supply piping system.

• Tribology and Lubricants
• /
• 제17권3호
• /
• pp.198-208
• /
• 2001

A Parametric study based on a computer analysis of the lubrication system of a four-cylinder gasoline engine is illustrated. Through the parametric study, the effects of various aeration levels on the change of oil flow rate and pressure are investigated. Also, at high oil temperature and low engine speed, the effect of oil aeration level on oil flow characteristics in lubrication system is investigated. The illustrated results may give to designers the guide lines of oil aeration level for the safe design of engine lubrication systems in terms of minimum pressure at crank oil bore.

• 반도체디스플레이기술학회지
• /
• 제12권2호
• /
• pp.93-98
• /
• 2013

Nanoimprint lithography (NIL) is a next generation technology for fabrication of micrometer and nanometer scale patterns. There have been considerable attentions on NIL due to its potential abilities that enable cost-effective and high-throughput nanofabrication to the display device and semiconductor industry. To successfully imprint a nanosized pattern with the thermal NIL, the process conditions such as temperature and pressure should be appropriately selected. This starts with a clear understanding of polymer material behavior during the thermal NIL process. In this paper, a filling process of the polymer resist into nanometer scale cavities during the thermal NIL at the temperature range, where the polymer resist shows the viscoelastic behaviors with consideration of stress relaxation effect of the polymer. In the simulation, the filling process and the residual layer formation are numerically investigated. And the effects of pressure and temperature on NIL process, specially the residual layer formation are discussed.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.69-75
• /
• 2004

The present study is numerically investigated for the high pressure effects on the vaporization process of the DME droplet. The evaporation rate of DME droplets is about twice that of dodecane droplets at the same chamber condition. The DM droplet vaporization characteristics is parametrically studied for the wide range of the operating conditions encountered with the high pressure combustion process.

• Food Science and Biotechnology
• /
• 제16권5호
• /
• pp.848-853
• /
• 2007

The effects of high-hydrostatic pressure (HHP) on the ginsenoside concentration in Korean red ginseng were investigated. HHP-pretreated Korean red ginseng samples were compared to samples produced by a conventional method. Six-year-old Korean fresh ginseng (Panax ginseng C.A. Meyer) samples were vacuum-packaged in polyethylene film and treated at room temperature for 1 min with HHP (200-600 MPa) and steamed at $98^{\circ}C$ for 3 hr. Major ginsenosides of red ginseng were analyzed by HPLC. HHP-pretreated red ginseng showed a 45% higher level of total major ginsenosides than conventionally prepared red ginseng. The levels of 4 protopanaxadiol-type ginsenosides increased 34-43% and the levels of 5 protopanaxatriol-type ginsenosides increased 45-66%. Scanning electron microscopy and electrical conductivity spectrum analysis showed that HHP pretreatment damaged ginseng plant cells and increased extraction efficiencies of ginsenosides from red ginseng products.