• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.342-343
• /
• 2012

We studied the Drain-Induced-Barrier-Lowering (DIBL) effect by different drain engineering. One other drain engineering is symmetric source-drain n-channel MOSFETs (SSD NMOSs), the other drain engineering is asymmetric source-drain n-channel MOSFETs (ASD NMOSs). Devices were fabricated using state of art 40 nm dynamic-random-access-memory (DRAM) technology. These devices have different modes which are deep drain junction mode in SSD NMOSs and shallow drain junction mode in ASD NMOSs. The shallow drain junction mode means that drain is only Lightly-Doped-Drain (LDD). The deep drain junction mode means that drain have same process with source. The threshold voltage gap between low drain voltage ($V_D$=0.05V) and high drain voltage ($V_D$=3V) is 0.088V in shallow drain junction mode and 0.615V in deep drain junction mode at $0.16{\mu}m$ of gate length. The DIBL coefficients are 26.5 mV/V in shallow drain junction mode and 205.7 mV/V in deep drain junction mode. These experimental results present that DIBL effect is higher in deep drain junction mode than shallow drain junction mode. These results are caused that ASD NMOSs have low drain doping level and low lateral electric field.

• ETRI Journal
• /
• 제38권2호
• /
• pp.244-251
• /
• 2016

In this paper, we investigate the electrical characteristics of two trench-gate-type super-barrier rectifiers (TSBRs) under different p-body implantation conditions (low and high). Also, design considerations for the TSBRs are discussed in this paper. The TSBRs' electrical properties depend strongly on their respective p-body implantation conditions. In the case of the TSBR with a low p-body implantation condition, it exhibits MOSFET-like properties, such as a low forward voltage ($V_F$) drop, high reverse leakage current, and a low peak reverse recovery current owing to a majority carrier operation. However, in the case of the TSBR with a high p-body implantation condition, it exhibits pn junction diode.like properties, such as a high $V_F$, low reverse leakage current, and high peak reverse recovery current owing to a minority carrier operation. As a result, the TSBR with a low p-body implantation condition is capable of operating as a MOSFET, and the TSBR with a high p-body implantation condition is capable of operating as either a pn junction diode or a MOSFET, but not both at the same time.

• 대한전자공학회논문지
• /
• 제21권1호
• /
• pp.62-70
• /
• 1984

비저항이 10Ω-cm, 두께가 13∼15mi1인 <111> oriented, p형 Si기판을 이용하여 N+PP+ BSF 전지와 에미터 영역이 N+N 고저 접합으로 이루어진 N+NPP+ HELEBSF(high low emitter bach surface field) 전지를 설계 제작하였다. 접합형 태양전지의 에미터 영역에서 고저 접합구조가 효율 개선에 미치는 영향을 검토하기 위해 HLEBSF 전지의 N영역을 제외하고는 같은 마스크와 동시 공정을 통해 N+PP-전지와 N+NPP+ 전지의 가영역에서 물리적 파라미터들(불순물 농도, 두께)을 동일하게 만들었다. 100mW/㎠의 인공조명에서 측정한 결과 N+PP+ 전지들의 전면적 (유효 수광면적) 평균 변환효율이 10.94%(12.16%)이었고, N+NPP+ 전지들의 평균 변환효율은 12.07% (13.41%)로 나타났다. N+NPP+ 전지의 효율개선은 N+N-고저 접합 에미터 구조가 N+ 에미터 영역에서 나타나는 heavy doping effects를 제거함으로써 에미터 재결합 전류의 증가를 억제하고 나아가 개방전압(Voc)과 단락전류(Ish)의 값을 증가시켜 준 결과로 볼 수 있다.

• Current Photovoltaic Research
• /
• 제8권3호
• /
• pp.94-101
• /
• 2020

This study was trying to focus on achieving high efficiency of multi junction solar cell with thin film silicon solar cells. The proposed thin film Si-Ge/c-Si tandem junction solar cell concept with a combination of low-cost thin-film silicon solar cell technology and high-efficiency c-Si cells in a monolithically stacked configuration. The tandem junction solar cells using amorphous silicon germanium (a-SiGe:H) as an absorption layer of upper sub-cell were simulated through ASA (Advanced Semiconductor Analysis) simulator for acquiring the optimum structure. Graded Ge composition - effect of E_g profiling and inserted buffer layer between absorption layer and doped layer showed the improved current density (J_sc) and conversion efficiency (η). 13.11% conversion efficiency of the tandem junction solar cell was observed, which is a result of showing the possibility of thin film Si-Ge/c-Si tandem junction solar cell.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.562-565
• /
• 2001

In this paper, novel device structures in order to realize ultra fast and ultra small silicon devices are investigated using ultra-high vacuum chemical vapor deposition(UHVCVD) and Excimer Laser Annealing (ELA). Based on these fundamental technologies for the deep sub-micron device, high speed and low power devices can be fabricated. These junction formation technologies based on damage-free process for replacing of low energy ion implantation involve solid phase diffusion and vapor phase diffusion. As a result, ultra shallow junction depths by ELA are analyzed to 10~20nm for arsenic dosage(2${\times}$10$\_$14//$\textrm{cm}^2$), exciter laser source(λ=248nm) is KrF, and sheet resistances are measured to 1k$\Omega$/$\square$ at junction depth of 15nm and realized sub-50nm n-MOSFET.

• Journal of Magnetics
• /
• 제14권1호
• /
• pp.11-14
• /
• 2009

We investigated the I-V curves and differential tunneling conductance of two, CoFeB/MgO/CoFeB-based, magnetic tunnel junctions (MTJs): one with a low tunneling magnetoresistance (TMR; 22%) and the other with a high TMR (352%). This huge TMR difference was achieved by different MgO sputter conditions rather than by different annealing or deposition temperature. In addition to the TMR difference, the junction resistances were much higher in the low-TMR MTJ than in the high-TMR MTJ. The low-TMR MTJ showed a clear parabolic behavior in the dI/dV-V curve. This high resistance and parabolic behavior were well explained by the Simmons' simple barrier model. However, the tunneling properties of the high-TMR MTJ could not be explained by this model. The characteristic tunneling properties of the high-TMR MTJ were a relatively low junction resistance, a linear relation in the I-V curve, and conduction dips in the differential tunneling conductance. We explained these features by applying the coherent tunneling model.

• E2M - 전기 전자와 첨단 소재
• /
• 제11권11호
• /
• pp.37-45
• /
• 1998

In this paper, present status of super high-efficiency tandem solar cells has been reviewed and key issues for realizing super high-efficiency have also been discussed. In addition, the terretrial R&D activities of tandem cells, in the New Sunshine Program of MITI(Ministry of International Trade and Industry) and NEDO(New Energy and Industrial Technology Development Organization) in Japan are reviewed briefly. The mechanical stacked 3-junction cells of monolithically grown InGaP/GaAs 2-junction cells and InGaAs cells have reached the highest efficiency achieved in Japan of 33.3% at 1-sun AM1.5. This paper also reports high-efficiency InGaP/GaAs 2-junction solar cells with a world-record efficiency of 26.9% at AM0, 28$^{\circ}C$ and radiation damage recovery phenomena of the tandem cell performance due to minority-carrier injection under light illumination or forward bias, which causes defect annealing in InGaP top cells. Future prospects for realizing super-high efficiency and low-cost tandem solar cells are also described.

• 한국전기전자재료학회논문지
• /
• 제28권8호
• /
• pp.496-500
• /
• 2015

This paper was proposed the theoretical research and optimal design 3000V super junction NPT IGBT for using electrical automotive and power conversion. Because super junction IGBT was showed ultra low on resistance, it was structure that can improve the thermal characteristics of conventional NPT IGBT. The electrical characteristics of super junction NPT IGBT were 2.52 V of on state voltage drop, 4.33 V of threshold voltage and 2,846 V breakdown voltage. We did not obtaing 3,000 V breakdown voltage but we will obtain 3,000 V breakdown voltage through improving p pillar layer. If we are carried this research, This device will be used electrical automotive, power conversiton and high speed train.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.103-103
• /
• 2008

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2001년도 춘계종합학술대회
• /
• pp.349-352
• /
• 2001

본 논문은 기가 SRAM급 이상의 초고집적을- 위한 0.1$\mu\textrm{m}$의 설계치수를 갖는 MOSFET의 게이트 영역에서 활성 부분의 면저항을 감소시키기 위해 n영역으로 비소를 이온 주입하였다. 어닐링은 급속 열처리 공정 방법과 엑시머 레이져 어닐링 방법을 이용하였으며, 극히 얕은 접합의 형성이 가능하였다. 얕은 접합 형성 깊이는 10~20nm이며, 비소의 주입량은 2$\times$$10^{14}$ $\textrm{cm}^2$이고, 레이져는 엑시머이며 소스는 KrF로 파장은 248mm로 어닐링 하였다. 극히 얕은 P/N$^{+}$ 접합 깊이가 15nm이며, 이때 1k$\Omega$/$\square$의 낮은 면저항 특성을 갖는 결과가 나타났다.