• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.169-175
• /
• 2013

CRDi technology of diesel engine was developed from in the early 2000s due to a need to increase fuel efficiency and environment care. Especially, high-pressure fuel injection system in CRDi system which has a fuel injection unit including an injector, a fuel pump and common-rail, etc. becomes possible to make the exhaust gas clean as well as power improvement. In this study, comparison of dynamic characteristics of servo-hydraulic piezo-driven injector with 3-way and bypass-circuit type was analyzed by using the AMESim code. As results of this study, it found the bypass-circuit inside servo-hydraulic piezo injector can cause a faster injection response than that of the 3-way type. Also it was shown that bypass-circuit type had better control capability due to hydraulic bypass system.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.110-115
• /
• 2015

In this paper it is proposed to solve the problem of particulate matter reducing apparatus of the current DPF. One exhaust gas passage 2-way controlled to purify the exhaust gas generated during combustion efficiently. Through the control of the rotary valve within a single device, it is possible to prevent the exhaust pressure increases due to particulate matter accumulate inside the developing DPF. Develop DPF device capable of inducing a high efficiency of the output in order to improve the problem of reducing the engine output and fuel efficiency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.465-467
• /
• 2010

This paper proposes MIMO two-way cooperative relay scheme to optimize the end to end capacity in wireless multi-hop mesh network. The basic idea is to perform data transmission via multi-hop relay nodes, in equidistant topology, this method is quite efficient. However, on one hand this topology is very rare in practical situation, on the other hand, in real practical situation where the topology is most likely non equidistant, the end to end capacity significantly degrades due to bottleneck link caused by uneven SNR. Moreover, the end to end capacity degrades at high SNR due to overreach interference from far nodes existing in multi-hop relay networks. In this paper, MIMO two-way cooperative relay in the region of non equidistant nodes is found efficient to improve the end to end capacity. The proposed scheme is validated using numerical simulation.

• Transactions of Materials Processing
• /
• v.33 no.5
• /
• pp.330-340
• /
• 2024

The martensitic Ni-Ti shape memory alloys(SMA) can achieve a two-way shape memory effect (TWSME) through thermomechanical training/cycling. In this study, the surface of Ni-Ti SMA sheets was treated by depositing a certain number of titanium (Ti) powder layers using a selective laser meling (SLM) process to enhance TWSME. The results showed that a unique TWSME of approximately 12% with good stability was achieved after 100 training cycles when the optimum number of five Ti layers was deposited. A larger HAZ and lower cooling rate pushed more Ti particles into the grains rather than the grain boundaries, providing more time for Ti to react with NiTi to form Ti-rich intergranular Ti2Ni(Ox) precipitates. This resulted in further hindering of dislocation movement within the grains and the generation of internal stress fields required for attaining a larger TWSME. With an increase in the number of Ti-deposited layers, there was no noticeable reduction in the one-way shape memory effect (OWSME) through the initial cycling. This was due to the high residual tensile stress caused by the lower thermal expansion of the Ti layer compared to the Ni-Ti sheet.

• Journal of the Korea Convergence Society
• /
• v.8 no.6
• /
• pp.1-7
• /
• 2017

This study examined how the memory effect and the brand attitude effect differ according to the interaction (high / low) and the involvement (high / low) of digital signage. The two-way MANOVA analysis using SPSS 18 was used for the empirical analysis. The results of this study are as follows: First, GRM is recalled if the level of interactivity and inffence of digital signage is low, but if both conditions are high, ARM recalls. Second, if the interaction of digital signage is low and the level of engagement is high, a lot of memory information is formed that forms the overall attitude of the product. In addition, even though the interaction level is high and the engagement is low, the attitude cognitive response through the overall evaluation is formed rather than the attribute information. Third, brand attitude was positive when interactivity level was high and engagement level was high.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.100-100
• /
• 2016

Among various two-dimensional (2D) materials, 2D semiconductors and insulators have attracted a great deal of interest from nanoscience community beyond graphene, due to their attractive and unique properties. Such excellent characteristics have triggered highly active researches on 2D materials, such as hexagonal boron nitride (hBN), molybdenum disulfide (MoS2), and tungsten diselenide (WSe2). New physics observed in 2D semiconductors allow for development of new-concept devices. Especially, these emerging 2D materials are promising candidates for flexible and transparent electronics. Recently, van der Waals heterostructures (vdWH) have been achieved by putting these 2D materials onto another, in the similar way to build Lego blocks. This enables us to investigate intrinsic physical properties of atomically-sharp heterostructure interfaces and fabricate high performance optoelectronic devices for advanced applications. In this talk, fundamental properties of various 2D materials will be introduced, including growth technique and influence of defects on properties of 2D materials. We also fabricate high performance electronic/optoelectronic devices of vdWH, such as transistors, memories, and solar cells. The device platform based on van der Waals heterostructures show huge improvement of devices performance, high stability and transparency/flexibility due to unique properties of 2D materials and ultra-sharp heterointerfaces. Our work paves a new way toward future advanced electronics based on 2D materials.

• Journal of the Korean Magnetic Resonance Society
• /
• v.14 no.1
• /
• pp.38-44
• /
• 2010

In liquids NMR, $^{1}H$ is the most widely observed nucleus, which is not the case in solids NMR. The reason is due to the strong homo-dipolar interactions between the hydrogen atoms which mask the useful chemical shift information. Therefore we must remove the strong homo-dipolar interactions in order to get structural information, which can be investigated by the isotropic chemical shift. There are two ways of obtaining it. One is the ultra-fast MAS of ca. 70 kHz spinning speed, which has become available only recently. The other way is devising a pulse sequence which can remove the strong homo-dipolar interaction. In the latter way, MAS with a moderate spinning rate of a few kHz, is enough to remove the chemical shift anisotropy. In this report, 1D-CRAMPS and 2D MASFSLG techniques are utilized and their results will be compared. This kind of highresolution $^{1}H$ NMR for solids, should become a valuable analytical tool in the understanding and the developing of a new class of hydrogen storage materials. Here ammonium borane $-NH_{3}BH_{3}$, whose hydrogen content is high, is used as a sample.

• Korean Journal of Computational Design and Engineering
• /
• v.11 no.4
• /
• pp.315-325
• /
• 2006

It is very often necessary to search for similar parts during designing a new product because its parts are often easily designed by modifying existing similar parts. In this way, the design time and cost can be reduced. Thus it would be nice to have an efficient similarity comparison algorithm that can be used anytime in the design process. There have been many approaches to compare shape similarity between two solids. In this paper, two parts represented in B-Rep is compared in two steps: one for overall appearances and the other for detail features. In the first step, geometric information is used in low level of detail for easy and fast pre-classification by the overall appearance. In the second step, feature information is used to compare the detail shape in high level of detail to find more similar design. To realize the idea above, a multi resolution algorithm is proposed so that a given solid is described by an overall appearance in a low resolution and by detail features in high resolution. Using this multi-resolution representation, parts can be compared based on the overall appearance first so that the number of parts to be compared in high resolution is reduced, and then detail features are investigated to retrieve the most similar part. In this way, computational time can be reduced by the fast classification in the first step while reliability can be preserved by detail comparison in the second step.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.77-82
• /
• 2006

Automatic vessel collision-avoidance systems have been studied in the fields of artificial intelligence and navigation for decades. And to facilitate automatic collision-avoidance decision-making in two-vessel-encounter situation, several expert and fuzzy expert systems have been developed. However, none of them can negotiate with each other as seafarers usually do when they intend to make a more economic overall plan of collision avoidance in the COLREGS-COST-HIGH situations where collision avoidance following the International Regulations for Preventing Collisions at Sea(COLREGS) costs too much. Automatic Identification System(AIS) makes data communication between two vessels possible, and negotiation methods can be used to optimize vessel collision avoidance. In this paper, a negotiation framework is put forward to enable vessels to negotiate to optimize collision avoidance in the COLREGS-COST-HIGH situations at open sea. A vessel vector space is defined and therewith a cost model is put forward to evaluate the cost of collision-avoidance actions. Negotiations between a give-way vessel and a stand-on vessel and between two give-way vessels are considered respectively to reach overall low cost agreements. With the framework proposed in this paper, two vessels involved in a COLREGS-COST-HIGH situation can negotiate with each other to get a more economic overall plan of collision avoidance than that suggested by the traditional collision-avoidance expert systems.

• Journal of Fashion Business
• /
• v.13 no.4
• /
• pp.51-59
• /
• 2009

The purpose of this research is to investigate the influences of service experience and brand reputation on intention by word of mouth(WOM) when consumers get experiences at beauty salon. We made 2(valence of service experience: positive/negative) ${\times}$ 2(brand reputation level: high/low) subjects experimental design in order to find reason that there is a significant difference of intention by word of the mouth between positive experience condition and negative experience condition. Also we tried to find the interaction of two factors. To test our hypothesis, an experiment was performed on 68 university students in seoul area. Specifically, we used 2-way ANOVA and planned contrast method through SPSS 12.0 procedure. As a result, a two-way ANOVA demonstrated a significant main effect of service experience, which means that people more intend to make WOM when they experience a negative service than a positive service. Also the ANOVA showed a significant interaction effect between service experience and brand reputation, which represents that people more intend to make WOM for high-reputed(low-reputed) brand than low-reputed(high-reputed) brand when they encounter negative(positive) services.