• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.

• Journal of Fisheries and Marine Sciences Education
• /
• v.27 no.5
• /
• pp.1352-1363
• /
• 2015

This study was carried out to investigate the characteristics of the dependent variables depending on the condition changes of independent variable of the operation and the material during the production of collets added with rice and dried shrimp by using single extruder to utilize as basic data for the manufacture of extrusion collets. A total of 7 independent variables were set up as a raw, 20, 40 and 60 mesh for the powder particle size of rice; 12, 14, 16 and 18% for the moisture content of rice; 2, 4, 6 and 8% for the addition amount of dried shrimp; 90, 95, 100 and $110^{\circ}C$ for the barrel temperature; 210, 280 and 340 rpm for the screw speed; 4, 6, 8 and 10 mm for the discharge port diameter; 30, 40, 50 and 60 kg/h for the input amount of the mixed material. The characteristics of the dependent variables including puffing ratio, moisture content, lightness, uniformity, productivity of collets was to be studied by changing the conditions of the independent variables. As a results of this study, 20 mesh of powder particle size of rice, 14% of moisture content of rice, 4% of addition amount of dried shrimp, $100^{\circ}C$ of barrel temperature, 280 rpm of screw speed, 6 mm of discharge port diameter and 50 kg/h of input amount of mixed material were found to be the most preferable over other independent variables for the production of extrusion collets. In conclusion, it is necessary to set the independent variable in order to produce the high quality collets added with the rice as the main raw material and dried shrimp as the sub-materials.

• Journal of Korean Society of Forest Science
• /
• v.80 no.2
• /
• pp.151-161
• /
• 1991

I tried to specify the taxa of Fagaceae in Korea by the character of their pollen grains. The light microscope(LM) and the Scanning electron microscope(SEM) were used to examine the pollen grains of 19 taxa, 5 genera. The result are as follows. 1. The pollen of Fagaceae in Korea could be grouped into four types and 4 subtypes. 1) Fagus type 2) Castanea type 3) Lithocarpus, Castanopsis type 4) Quercus type (1) Cyclobalanopsis subtype (2) Prinus subtype (3) Dentatae subtype (4) Cerris subtype. 2. The morphology of the granula on the pollen of Quercus was closely related to the differantiation of the shape of the cup scales. 1) The uniformity of branching granula on the pollen grain surface corresponds to the morphological features of the concentric arrangement of cup scales. 2) The morphological features of the pollen grain surface intermingled with large or small granula, simple-granula and tuber granula which have small points of circular prominence, corresponded to those of short cup scales. 3) The morphological features of the polllen grain surface intermingled with large or small granula, simple-granula and tuber granula with an apex of amoeba type corresponded to those of Q. dentata Thunb, with thin, fine and long cup scales. 4) The morphological features of the pollen grain surface intermingled with large of small granula of with only simple-granula, corresponded to those of Q. acutissima carr. with thick, fine and long cup scales. 3. The result of cluster analysis by coding the sculpture pattern of the pollen grain surface, the existence and nonexistence of surface perforate, the grain size and granula type were coincident with the system of classification of plants and showed an intimated relationship even under th level of species.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.7
• /
• pp.914-920
• /
• 2008

In this study, hard roll breads were prepared with 3, 6, 9, 12, and 15% of concentrated sweet pumpkin powder (CSPP). The samples and a control were then compared in terms of quality characteristics, including pH, total titratable acidity, fermentation power of dough expansion, specific volume, baking loss, moisture content, color, textural characteristics, external and internal surface appearances, and sensory qualities of bread in order to determine the optimal ratio of CSPP in the formulation. As CSPP content increased, pH of dough, specific volume, baking loss, and lightness of bread decreased, while total titratable acidity of dough, pH, total titratable acidity, moisture content, and redness of bread increased. Fermentation power of dough expansion increased as incubation time increased. The CSPP samples had significantly higher yellowness, hardness, cohesiveness, gumminess, chewiness, and resilience than the control group. Adhesiveness was the highest at the 12% substitution level, while the lowest at the 6% level. Springiness increased with increasing CSPP content. In the sensory evaluation, as CSPP content increased, scores for color and consistency of crumb decreased, while scores for aroma of sweet pumpkin, sweetness, and delicious taste increased. Density of crumb pore were maximal with the 12% CSPP substitution. The CSPP samples had significantly higher uniformity of crumb pore and springiness of crumb than the control group. However, mouth-feel and overall acceptability showed the reverse effect, obtaining fairly good scores. In conclusion, the results indicate that substituting $6{\sim}9%$ CSPP to hard roll bread is optimal, providing good physiological properties as well as reasonably high overall acceptability.

• Progress in Medical Physics
• /
• v.9 no.3
• /
• pp.137-141
• /
• 1998

The purposes of this report are to evaluate whether lead ball and steel ball could be used as protective material of radiation and to acquire physical data of them for protecting 4-10 MV X-ray beams. Lead balls of diameter 2.0～2.5mm or steel balls of diameter 1.5～2.0 mm were filled in an acrylic box of uniform width. An MV radiograph of metal balls in a box were taken to ascertain uniformity of ball distribution in the box. Average density of metal ball and linear attenuation coefficient of metal balls for 4～10 MV X -rays were measured. At the time of measurement of linear attenuation coefficient, Farmer ionization chamber was used and to minimize the scatter effect, distance between the ball and the ionization chamber was 70 cm and field size was 5.5cm${\times}$5.5cm. For comparison, same parameters of lead and steel plates were measured. The distribution of metal balls was uniform in the box. The density of a mixture of lead-air was 6.93g/cm$^3$, 0.611 times density of lead, and the density of a mixture of steel-air was 4.75g/cm$^3$, 0.604 times density of steel. Half-value layers of a mixture of lead-air were 1.89 cm for 4 MV X-ray, 2.07 cm for 6 MV X-ray and 2.16 cm for 10 MV X-ray, and approximately 1.64 times of HVL of lead plate. Half-value layers of a mixture of steel-air were 3.24 cm for 4 MV X-ray, 3.70 cm for 6 MV X-ray and 4.15 cm for 10 MV X-ray, and approximately 1.65 times of HVL of lead plate. Metal balls can be used because they could be distributed evenly. Average densities of mixtures of lead-air and steel-air were 6.93g/cm$^3$, 4.75g/cm$^3$ respectively and approximately 1.65 times of densities of lead and steel. Product of density and HVL for a mixture of metal-air are same as the metal.

• The Journal of Korean Society for Radiation Therapy
• /
• v.20 no.1
• /
• pp.37-43
• /
• 2008

Purpose: To evaluate dosimetry results of three different techniques for whole breast irradiation after conservative surgery of large pendulous breast patient. Materials and Methods: Planning computed tomography (CT) scans for three techniques were performed on a GE Hi-speed advantage CT scanner in the supine (SP), supine with breast supporting Device (SD) and prone position on a custom prone mattress (PP). Computed tomography images were acquired at 5 mm thickness. The clinical target volumes (CTV), ipsilateral lung and heart were delineated to evaluate the dose statistic, and all techniques were planned with the tangential photon beams (Pinnacle$^3$, Philips Medical System, USA). The prescribed dose was 50 Gy delivered in 25 fractions. To evaluate the dose coverage for CTV, we analysed percent volume of CTV receiving minimum of 95%, 100%, 105%, and 110% of prescription dose ($V_{95}$, $V_{100}$, $V_{105}$, and $V_{110}$) and minimal dose covering 95% ($D_{95}$) of CTV. The dosimetric comparison for heart and ipsilateral lung was analysed using the minimal dose covering 5% of each organs ($D_5$) and the volume that received >18 Gy for the heart and >20 Gy for the ipsilateral lung. Results: Target volume coverage ($V_{95}$ and $V_{100}$) was not significantly different for all technique. The V105 was lower for PP (1.2% vs. 4.4% for SP, 11.1% for SD). Minimal dose covering 95% ($D_{95}$) of target was 47.5 Gy, 47.7 Gy and 48 Gy for SP, SD and PP. The volume of ipsilateral lung received >20 Gy was 21.7%, 11.6% and 4.9% for SP, SD and PP. The volume of heart received >18 Gy was 17.0%, 16.1% and 9.8% for SP, SD and PP. Conclusion: Prone positioning of patient for large pendulous breast irradiation enables improving dose uniformity with minimal heart and lung doses.

• Korean Journal of Materials Research
• /
• v.8 no.7
• /
• pp.621-627
• /
• 1998

The formation of Co-silicide between Co/Zr bilayer on the amorphous and crystalline Si substrates has been investigated. The films of Zr(50$\AA$) and Co(l50$\AA$) were deposited with e-beam evaporation system and were heattreated with the rapid thermal annealing system at the temperatures between 50$0^{\circ}C$ and 80$0^{\circ}C$ with 10$0^{\circ}C$ increments for 30 seconds. The phase identification of Co-silicide was carried out by XRD and the chemical analysis was examined by AES and RBS. The interface morphologies of Co/Zr bilayer films were investigated by cross sectional TEM and HRTEM. $CoSi_2$ was formed epitaxially on the crystalline Si substrate above $700^{\circ}C$ while polycrystalline $CoSi_2$ was grown on the amorphous Si substrate. The formation temperature of Co-silicide on the amorphous Si substrate was about 100 C lower than that on the crystalline Si. The COzSi phase was not identified on the both Si substrates. The formation temperature of first phase of Co-silicide on ColZr bilayer was higher than that on Co mono layer. CoSizlayer formed on the amorphous Si substrate exhibits better uniformity compared to the CoSiz formed on the crystalline substrate. The sheet resistance of CoSiz layer on crystalline Si was lower than that on the amorphous Si at high temperatures.tures.

• Journal of Chest Surgery
• /
• v.29 no.10
• /
• pp.1081-1089
• /
• 1996

Pulmonary atresia with intact ventricular septum has continued to have a high surgical mortality and morbidity. This mAy attribute to the non-uniformity of the anomaly. We reviewed a total of 34 infants with pulmonary atresla and intact ventricular septum managed in this hospital between 1987 and 1995. Mean age and body weight were 57.2 (range, 3-208) days and 4.1 (range, B.3∼6.8) kg. The preoperative Z-value of the diameter of the tricuspid valve was less than -2 in 85.2% of patients and less than -4 in 33. 3% . It is well correlated w th right ventricular cavity size (n=27. r10.68, p< 0.05). Coronary artery-right ventricular fistulas were identified in 3 patients, and right ventricular dependency was suspected in 1 Over All hospital mortality was 23.5%(8/34), although it decreased to 16.6%(4124) in 1990s. Subsequent procedures were performed in 6 patients between 3 days and 58 months after Initial palliation : one bidirectional cavopulmonary shunt and 1 Fontan operation after systemic-pulmonary shunt, 3 transannular patch + atrial septal defect closure and 1 additional systemic-pulmonary shunt after polmonary valvectomy or valvotomy. Changes of Z-values of the diameter of tricuspid valve have been followed up in 11 patients between 1 and 66 months postoperatively. Z-values were increased In 5 out of 8 transannular right ventriculAr outflow tract enlargement group and in 1 out of 3 pulmonary valvectomy or valvotomy group. Our data suggest that tailoring a treatment to right ventricular cavity size and coronary anom lies may improve the surgical outcome. A Z-value of the tricuspid valve diameter could be used.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.10
• /
• pp.1294-1300
• /
• 2008

Nelumbo nucifera G. tea white breads were prepared by the addition of 0.01, 0.02, 0.03, and 0.04% hemicellulase to flour of the basic formulation. The experiments and control were then compared in terms of quality characteristics, including pH, total titratable acidity, fermentation power of dough expansion, specific volume, baking loss, moisture content, color, textural characteristics, external and internal surface appearances, and sensory qualities in order to determine the optimal ratio of hemicellulase in the formulation. There were no significant differences in pH and total titratable acidity of dough among the experiments. Fermentation power of dough expansion were increased as incubation time increased. Baking loss was the highest at the 0.04% addition level, while the lowest at the 0.01% level. As hemicellulase content increased, pH, hardness, and fracturability of bread decreased, while total titratable acidity, specific volume, and resilience increased. Water content and lightness were the highest in the control bread samples, and yellowness was maximal in the 0.01% group. Bread made by the addition of hemicellulase had significantly higher greenness and flavor than the control group. Color, consistency, and springiness of crumb, density and uniformity of crumb pore, softness, chewiness, overall acceptability, lotus leaf flavor, delicious taste, astringency, bitterness, and off-flavor were not significantly different among the samples. The results indicate that adding 0.02$\sim$ 0.03% hemicellulase in N elumbo nucifera G. tea white bread is optimal for quality and provides a product with reasonably high overall acceptability.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.107-108
• /
• 2008

The spectacular development of AMLCDs, been made possible by a-Si:H technology, still faces two major drawbacks due to the intrinsic structure of a-Si:H, namely a low mobility and most important a shift of the transfer characteristics of the TFTs when submitted to bias stress. This has lead to strong research in the crystallization of a-Si:H films by laser and furnace annealing to produce polycrystalline silicon TFTs. While these devices show improved mobility and stability, they suffer from uniformity over large areas and increased cost. In the last decade we have focused on microcrystalline silicon (${\mu}c$-Si:H) for bottom gate TFTs, which can hopefully meet all the requirements for mass production of large area AMOLED displays [1,2]. In this presentation we will focus on the transfer of a deposition process based on the use of $SiF_4$-Ar-$H_2$ mixtures from a small area research laboratory reactor into an industrial gen 1 AKT reactor. We will first discuss on the optimization of the process conditions leading to fully crystallized films without any amorphous incubation layer, suitable for bottom gate TFTS, as well as on the use of plasma diagnostics to increase the deposition rate up to 0.5 nm/s [3]. The use of silicon nanocrystals appears as an elegant way to circumvent the opposite requirements of a high deposition rate and a fully crystallized interface [4]. The optimized process conditions are transferred to large area substrates in an industrial environment, on which some process adjustment was required to reproduce the material properties achieved in the laboratory scale reactor. For optimized process conditions, the homogeneity of the optical and electronic properties of the ${\mu}c$-Si:H films deposited on $300{\times}400\;mm$ substrates was checked by a set of complementary techniques. Spectroscopic ellipsometry, Raman spectroscopy, dark conductivity, time resolved microwave conductivity and hydrogen evolution measurements allowed demonstrating an excellent homogeneity in the structure and transport properties of the films. On the basis of these results, optimized process conditions were applied to TFTs, for which both bottom gate and top gate structures were studied aiming to achieve characteristics suitable for driving AMOLED displays. Results on the homogeneity of the TFT characteristics over the large area substrates and stability will be presented, as well as their application as a backplane for an AMOLED display.