• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.65-84
• /
• 2011

Study of superconductivity in layered iron-based materials was initiated in 2006 by Hosono's group, and boosted in 2008 by the superconducting transition temperature, $T_c$, of 26 K in $LaFeAsO_{1-X}F_X$. Since then, enormous researches have been done on the materials, with $T_c$ reaching as high as 55 K. Here, we review briefly experimental and theoretical results on atomic and electronic structures and magnetic and superconducting properties of FeAs-based superconductors and related compounds. We seek for clues for unconventional superconductivity in the materials.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.399-403
• /
• 2002

Squeeze film dampers (SFDs) are designed and analyzed for radial superconducting bearings. The designed SFDs are mounted on the superconductors submerged in liquid nitrogen such that the dampers should supply additional damping to the relatively underdamped superconducting bearing support . Basic theory of SFD assembled with superconductors is introduced. Rotordynamic simulations are provided to support the feasibility of the superconducting bearings mounted on SFDs for a horizontal flywheel energy storage system.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.267-275
• /
• 1989

YBa2Cu3O7-x oxide superconductors were fabricated by sintering and hotisostatic pressing (HIP), and their microstructures and properties were compared with each other. Thougha part of the second phase was observed along grain boundaries, their structures were consisted of single (123) phase and they had many porosities. But, porosities were remakably reduced by Hiping and the densification was brought about. The structure of (123) compound also showed a number of twins, which are typical of high Tc superconductors. The on-set temperature of YBa2Cu3O7-x compound sintered at 96$0^{\circ}C$ in oxygen and hipped at 88$0^{\circ}C$ was highest, but that shwoed 0 resistance at 87$^{\circ}$K, which is a little lower than the compound sintered at 96$0^{\circ}C$. HIP treatment also increased the critical current density of as-sintered compound. However, its value was low, which may be ascribed to the many pores of starting-sintered compact and partially to the second phase along grain boundaries.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1990.10a
• /
• pp.36-38
• /
• 1990

In this study, a new sintered specimens of Y$\_$1-x/Sm$\_$x/Ba$_2$Cu$_3$O$\_$y/ is composed by substituting Sm for a part of Y in the YBa$_2$Cu$_3$O$\_$y/ high Tc superconductor, in order to study of making (Y$.$Sm)-Ba-Cu-O system sintered specimens and their characteristics. An their change affected on superconductivity and their characteristics are studied by changing the x range of the composition rate. The resistances of electrical characteristics under the conditions of the composition and the temperature are measured by using Ac four probe method in the procedure of this experiments. And it is confirmed that the Meissner effect from the superconductivity of composed Sm system exists in the range of 0

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.22-22
• /
• 2000

The discoveries of high temperature superconductors received great attention due to their high critical temperatures. These materials also exhibit extremely high critical magnetic fields and high critical current density at low temperature, high magnetic field. Thus, they are the most promising materials for superconducting magnets above 20 T. In this talk, progress in the development of HTS materials and insert coils at the National High Magnetic Field Laboratory will be reviewed. In 1999, a Bi-2212 stack of double pancakes generated 3 T in a 19 T background field. These results will be reviewed in terms of implications for future systems. Individual double pancakes of Bi-2223 have also been tested and their performance will also be discused. The present goal of a 57 system will be presented and the key technical requirements for larger, higher field systems will be addressed. It will be shown that in addition to increased critical current density, improved mechanical performance (stain resistanced) is necessary for high field systems. Furthemore, improvements in the conductor n-value will improve prospects for operational systems.

• Journal of the Korean Magnetics Society
• /
• v.2 no.3
• /
• pp.228-232
• /
• 1992

Magnetic properties of grain aligned high $T_c\;Y_1Ba_2Cu_3O_{7-y}$ superconductor are inverstigated. Grain-aligned superconductors have magnetic anisotropy in the Cu-O layer like single crystals. The lower critical field $H_{c1},$ measured at the temperature range of 2 K up to 77 K, is found to be decreasing linearly as temperature goes up. Moreover, it decreaes more rapidly when the Cu-O layer is perpendicular to the external magnetic field. The temperature dependence of the magnetic susceptibility shows that the value of magnetic susceptibility, $4{\pi}\;X,$ is close to -1 at low temperature. The intra grain critical current density $J_c,$ obtained from the Bean's critical state model, is found to be comparable to that of single crystal superconductors.

• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.103-113
• /
• 1998

By using a gas-tight electrochemical cell, we can perform high-temperature coulometric titration and measure electronic transport properties to determine the elecronic defect structure of metal oxides. This technique reduces the time and expense required for conventional thermogravimetric measurements. The components of the gas-tight coulometric titration cell are an oxygen sensor, Pt/yttria stabilitized zirconia(YSZ)/Pt, and an encapsulated metal oxide sample. Based on cell design, both transport and thermodynamic measurements can be performed over a wide range of oxygen partial pressure ($pO_2=10^{-35}$ to 1 atm). This paper describes the high-temperature gas-tight electrochemical cells used to determine electronic defect structures and transport properties for pure and doped-oxide systems, such as YSZ, doped and pure ceria $(Ca-CeO_2 \;and\; CeO_2)$, copper oxides and copper-oxide-based ceramic superconductors, transition metal oxides, $SrFeCo_{0.5}O_x,\; and \;BaTiO_2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.3
• /
• pp.269-274
• /
• 2002

(Sm/Y)-Ba-Cu-O system high Tc composite superconductors with/without $CeO_2$ additive were directionally grown by zone-melting process, haying large temperature gradient, In air atmosphere. Cylindrical green rods of $({Sm/y})_{1.8}Ba_{2.4}Cu_{3.4}O_x$ [(Sm/Y)1.8] composite oxides by cold isostatic pressing(CIP) method using rubber mold were fabricated. The microstructure and superconducting properties were investigated by XRD, SEM, TEM and SQUID magnetometer. The size of nonsuperconducting $({Sm/y})_2BaCuO_5$ inclusions of the melt-textured (Sm/Y)1.8 sample with CeO$_2$ additive were remarkably reduced and uniformly distributed within the superconducting (Sm/Y)1.8 matrix. Both samples, with/without $CeO_2$ additive, showed an onset Tc $\geq$ 90 K and sharp superconducting transition. The critical current density Jc value of the $CeO_2$ addictive were $1{\times}10^5A/\textrm{cm}^2$ in 77 K, 0 Tesla.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.2
• /
• pp.110-113
• /
• 2016

(YNdSm)-Ba-Cu-O system high Tc composite superconductors were directionally grown by zone melting process, having large temperature gradient, in air atmosphere. Cylindrical green rods of $(YNdSm)_{1.8}Ba_{2.4}Cu_{3.4}O_x$ [(YNS)1.8]composite oxides by CIP (cold isostatic pressing) method using rubber mold were fabricated. The microstructure and superconducting properties were investigated by XRD, TEM and SQUID magnetometer. The size of nonsuperconducting $(YNdSm)_2BaCuO_5$ inclusions of the melt-textured (YNS)1.8 sample with $CeO_2$ additive were remarkably reduced and uniformly distributed within the superconducting (YNS)1.8 matrix. (YNS)1.8 samples, with / without $CeO_2$ additive, showed an onset $T_c{\geq}90K$ and sharp superconducting transition. The critical current density $J_c$ value of the (YNdSm)1.8 superconductor with $CeO_2$ additive were 840 A, $1.2{\times}104A/cm^2$ in 77 K, 0 Tesla by direct current transport method.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.207-207
• /
• 2003

Uncooled infrared(IR) detectors that use a microbolometer with a large focal-plane array(FPA) have been developed with surface micromachining technology. There are many materials for microbolometers, such as metals, vanadium oxide, semiconductors and superconductors. Among theses, vanadium oxide is a promising material for uncooled microbolometers due to it high temperature coefficient of resistance(TCR) at room temperature. It is, however, is very difficult to deposit vanadium oxide thin films having a high TCR and low resistance because of the process limits in microbolometer fabrication. In general, vanadium oxides have been applied to microbolometer in mixed phases formed by ion beam deposition methods at low temperature with TCR in the range from -1.5 to -2.0%K.