• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.97-102
• /
• 2003

Experimental investigations were carried out in an atmospheric pressure, optically accessible and laboratory-scale dump combustor operating on natural gas. The objective of this study is to obtain the phase-resolved gas temperatures at different phases of the oscillating pressure cycle during unstable combustion. CARS temperature measurements were made at several spatial locations under lean premixed conditions to get the information on temperature field within the combustor. Also the effect of incomplete fuel-air mixing on phase-resolved temperature fluctuation was investigated. Results including phase-resolved averaged temperature, normalized standard deviation and temperature probability distribution functions (PDFs) were provided in this paper. Temperature PDFs give an insight on the flame behavior. And strong correlation between phase-resolved temperature profile and pressure cycle was observed. Results of the phase-resolved high temperature give an additional information on the perturbation of equivalence ratio at flame as well as the effect of mixing quality on NOx emission characteristics.

• Tribology and Lubricants
• /
• v.17 no.4
• /
• pp.297-306
• /
• 2001

Under the condition of variable density and specific heat, maximum pressure, maximum temperature, bearing load, friction and side leakage in high-speed journal bearing operation are examined within some degree of Journal misalignment. The results are compared with the calculation results under the conditions of constant density and specific heat, and variable density and constant specific heat. It is found that the condition of variable density and specific heat play important roles in determining friction and load of Journal bearing at high speed operation.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.1 no.4
• /
• pp.182-189
• /
• 1977

The propagating flame temperature of the Propane-Air premixture by using 30.$\mu$ and 50.$\mu$ diameter platinum sensing wires, that is, Two Wires Correction Method, Through the constant volume burining inside the 150mm diameter, 30mm height combustion chamber under the circumstances of the atomospheric pressure, and the room temperature was determined. Also the temperature distribution across High Temperature Region, i.e. Flame Front, and the temperature profile behind the flame the front have been obtained.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.6
• /
• pp.868-874
• /
• 2002

A high-impulse, low-power, digital microthruster has been developed using low-boiling-temperature liquid propellant with high-viscosity fluid plug. The viscous fiction force of the fluid plug increases the blast pressure and the low-boiling-temperature liquid propellant is intended to reduce input power consumption. The three-layer microthruster has been fabricated by surface micromachining as well as bulk micromachining in the size of 7$\times$13$\times$1.5㎣. A digital output impulse bit of 6.4$\times$10$^{-8}$ Nsec has been obtained from the fabricated microthruster using perfluoro normal hexane (FC72) propellant and oil plug, resulting in about ten times increase of the impulse bit using one hundredth electrical input energy compared to the conventional multiple-shot microthruster.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.59-63
• /
• 2001

A high-impulse, low-power, continuous-shot microthruster has been developed using low boiling temperature liquid-propellant with high viscous fluid-plug. The viscous friction force of the fluid-plug increases the blast pressure and the low boiling temperature liquid-propellant is intended to reduce input power consumption. The three-layer microthruster has been fabricated by surface micromachining as well as bulk micromachining in the size of $7{\times}13{\times}1.5mm^{3}$. A continuous output impulse bit of $6.4{\times}10^{-8}N{\cdot}sec$ has been obtained from the fabricated microthruster using perfluoro normal hexane (FC72) propellant and oil plug, resulting in about ten times increase of the impulse bit using one hundredth electrical input energy compared to the conventional continuous microthruster.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.78-84
• /
• 1999

A compact air-preheating type heat exchanger was developed and tested for the ultra-high temperature heat recovery applications. For the direct use of exhaust gases up to $1200^{\circ}C$, the heat exchanger adopted a ceramic core with high strength and low thermal expansion coefficient less than $1{\times}10^{-6}^{\circ}C^{-1}$. The ceramic core was fabricated by special extrusion and bonding techniques. To minimize thermal stresses in the core, spring-loaded sealing mechanism was designed and successfully installed. 1-pass air flow scheme was adopted for the compactness and cost-savings. The pressure test for the ceramic core showed no failure under 35 kPa and less than 3% leak under 7 kPa. Flue gas simulation system was developed to investigate the performance of the heat exchanger. The test results showed normal operations of the heat exchanger up to $1200^{\circ}C$ of exhaust gases and relatively high heat recovery efficiencies of 31～39% depending upon exhaust gas temperatures..

• Korean Journal of Food Science and Technology
• /
• v.29 no.6
• /
• pp.1202-1207
• /
• 1997

Inactivation of Leuconostoc sp. isolated from kimchi using carbon dioxide under pressure was investigated in terms of operating parameters in order to evaluate its feasibility as a novel nonthermal process. Inactivation rates increased with increasing pressure, temperature and exposure time, but with decreasing working volume. Microbial reduction of 3 log cycles was achieved within 150 min under a $CO_2$ pressure of $60\;kg/cm^2$ at 30^{\circ}C$. It was confirmed that microbial inactivation by the high pressure $CO_2$ was governed essentially by the characteristic of $CO_2$ mass transfer and thus penetration of $CO_2$, into cells was a rate limiting step to determine efficiency of the inactivation process. The experimental results suggested that the high pressure $CO_2$ treatment could be used as one of the effective nonthermal methods for preserving foods.

• Korean Journal of Food Science and Technology
• /
• v.33 no.2
• /
• pp.226-230
• /
• 2001

High hydrostatic pressure was applied to Foxtail Millet Takju to investigate the effects of high pressure on inactivation of microorganisms and enzymes. Total bacteria, lactic acid bacteria and yeast in untreated Takju were $6.8{\times}10^7,\;1.3{\times}10^8\;and\;8.4{\times}10^7\;CFU/mL$, respectively. Total bacterial count in Takju reduced to $2.2{\times}10^5\;CFU/mL$, while lactic acid bacteria and yeast were sterilized completely when heated at $65^{\circ}C$ for 30 min. Lactic acid bacteria and yeast decreased with the increase of treatment pressure, and pressurization of 400 MPa for 10 min at room temperature sterilized completely the lactic acid bacteria and yeast in Takju. Total bacteria were not sterilized with pressurization of even 600 MPa at room temperature. Total bacteria were completely sterilized at $66^{\circ}C/400\;MPa/60\;min\;and\;66^{\circ}C/600\;MPa/10\;min$. Pressurization of Takju caused a partial inactivation of ${\alpha}-amylase$, and after pressurization at 600 MPa for 10 min at room temperature, 73.2% of the original activity remained. The activity of glucoamylase increased with the increase of treatment pressure. Treatment at $66^{\circ}C/400\;MPa/10\;min$ reduced the activity of ${\alpha}-amylase$ by 59.7% and glucoamylase by 20.5%. ${\alpha}-Amylase$ was inactivated to less than 1.2% of the original activity at $66^{\circ}C/600\;MPa/30\;min$.

• Journal of the Korean Ceramic Society
• /
• v.23 no.1
• /
• pp.33-43
• /
• 1986

The synthesis of high-purity AlN by a vapor-phase reaction was investigated using the $NH_3-AlCl_3-H_2$ reacting system. The theoretical yields of AlN were determined from th thermodynamic equilibrium composi-tions. It was shown that the yields above 90% could by obtained even in the range of relatively low temper-ature of 600-1200K. The reaction temperature and the initial amounts/ratios of the reacting gases showed significant effects on the yields but the total pressure did not. The experimental results showed that a high-purity AlN having a needle shape was the only product as a solid phase and its amount produced increased with the reaction temperature. While the degree of agglmera-tion of the synthesized AlN increased with the reaction temperature the size of each particle consisting of the agglomerates was independent of the temperature but grew from 0.09 to 0.115${\mu}{\textrm}{m}$ with the flow rate of NH3. These experimental results were compared with the theoretical aspects for the synthesis of a high-purity AlN.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.5
• /
• pp.823-833
• /
• 2001

In recent years, the subject of remaining life assessment has drawn considerable attention in chemical plants, where various structural components typically operate at high temperature an pressure. Thus a life prediction methodology accounting for high temperature creep fracture is increasingly needed for the components. Critical defects in such structures are generally found in the form of semi-elliptical surface crack, and the analysis of which is consequently an important problem in engineering fracture mechanics. On this background, we first develop an auto mesh generation program for detailed 3-D finite element analyses of axial and circumferential semi-elliptical surface cracks in a piping system. A high temperature creep fracture parameter C-integral is obtained from the finite element analyses of generated 3-D models. Post crack growth module is further appended here to calculate the amount of crack growth. Finally the remaining lives of surface cracked pipes for various analytical parameters are assessed using the developed life assessment program.