• Korean Journal of Materials Research
• /
• v.1 no.3
• /
• pp.156-167
• /
• 1991

The purpose of this study is to develop a data base for material selection of turbofan engines, which is preferred in these days on many application due to their high performance with economical operation. Hundreds of Super Alloys have been developed by this time, each having special properties. Since it is very difficult task for a design engineer to select materials of adequate Properties for specific engine components, a good data bate is strongly desired to manage informations on various kinds of materials. However, no basic research is reported in this area so far in our country. The operating conditions such as temperature, pressure, rpm of spools are assumed to be provided by other mechanical studies. Creep rupture strength, corrosion resistance, yield strength, thermal expansion, melting point, etc., are considered as typical properties in this study to search a group of candidate materials. Formability, manufacturing or purchase cost can also be important variables to be considered. As a result of this study, a user-friendly computer program has been developed for input of new material information, interactive material selection, and output of selection results. Finally, discussion is presented from. the viewpoint of materials engineering. A method to evaluate the performance of the selected materials is also suggested.

• Economic and Environmental Geology
• /
• v.23 no.3
• /
• pp.287-308
• /
• 1990

The Ogmae alunite-kaolinite deposit occurs in acidic tuff, the Hwangsan Tuff, of upper Crataceous age in the Haenam volcanic field, SW Jeonnam. This deposit characterized by advanced argillic alteration formed $71.8{\pm}2.8{\sim}73.9{\pm}2.8$ Ma ago in very shallow depth environment with acid-sulfate solution. Wallrock alteration can be classified into four zones from the center to the margin of the deposit: alunite, kaolinite, illite, and silicified zone. The mineral assemblage in the alunite zone, ore zone, is alunite-quartz-pyritekaolinite. Consideration of stability relation of these minerals suggests that the maximum alteration temperature is estimated at about $250^{\circ}C$ with solution pH of 3 or below assuming that pressure does not exceed 0.3 Kb. Alunite occurs as two different types; replacement and vein-type deposit. The former one consists of fine grained alunite and the later one coarse grained and relatively pure alunite that formed by open space filling. Isomorphous substitution of Na for K in these two types of alunites range 0 to 40 %, indicating that Na/K ratio in the solution is spontaneously changed during the alteration process. Alunite which has higher Na substitution probably formed in an earlier stage while the solution sustain high Na/K ratio. K-Ar age of alunites indicate that the replacement alunite formed earlier($73.9{\pm}2.8Ma$) than the vein-type alunite($71.8{\pm}2.8Ma$). The ${\delta}^{34}S$ value of pyrite and alunite indicate that those minerals formed at isotopically nonequillibrium state. The ${\delta}^{16}O$ and ${\delta}D$ values, of kaolintics 5.0 to 9.0‰ and -54 to -99‰, respectively, indicate that those are formed by hydrothermal solution having magmatic origin which have been diluted by low ${\delta}D$ meteoric water.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.485-491
• /
• 2012

Due to increase in production of the domestic textile industry, energy consumption in textile industry is still growing. Traditional dyeing machine has high temperature and pressure. Accordingly, it uses an indirect cooling system that utilize a heat exchanger to cool after the dyeing. However, this indirect cooling system consumes a great deal of water, takes prolonged periods of time to process and, most importantly, because of the condensing of the dye at the cooling stage requires further energy in reduction cleaning and washing process. Therefore, in this paper, we propose a direct cooling washing machine that replaces the traditional indirect cooling system to provide coolant into the dyeing machine. The newly proposed direct cooling washing machine will still use parts of the traditional dying but will be able to skip the cooling as well as the reduction cleaning and washing process, resulting in less processing time and lower energy consumption. Also, we made a prototype. The prototype was applied to dyeing machine to test the direct cooling washing machine's ability and dyeing property. Additionally, we compared indirect cooling washing machine with direct cooling washing machine about ability, material and energy saving assessment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.375-375
• /
• 2012

Graphene is a sp2-hybridized carbon sheet with an atomic-level thickness and a wide range of graphene applications has been intensely investigated due to its unique electrical, optical, and mechanical properties. In particular, hybrid graphene structures combined with various nanomaterials have been studied in energy- and sensor-based applications due to the high conductivity, large surface area and enhanced reactivity of the nanostructures. Conventional metal-catalytic growth method, however, makes useful applications difficult since a transfer process, used to separate graphene from the metal substrate, should be required. Recently several papers have been published on direct graphene growth on the two dimensional planar substrates, but it is necessary to explore a direct growth of hierarchical nanostructures for the future graphene applications. In this study, uniform graphene layers were successfully synthesized on highly dense dielectric nanowires (NWs) without any external catalysts. We also demonstrated that the graphene morphology on NWs can be controlled by the growth parameters, such as temperature or partial pressure in chemical vapor deposition (CVD) system. This direct growth method can be readily applied to the fabrication of nanoscale graphene electrode with designed structures because a wide range of nanostructured template is available. In addition, we believe that the direct growth growth approach and morphological control of graphene are promising for the advanced graphene applications such as super capacitors or bio-sensors.

• Membrane Journal
• /
• v.28 no.2
• /
• pp.136-141
• /
• 2018

Carbon dioxide ($CO_2$) exists not only as a component of natural gas, biogas, and landfill gas, but also as a major combustion product of fossil fuels which leads to a major contributor to greenhouse gases. Hence it is essential to reduce or eliminate carbon dioxide ($CO_2$) in order to obtain high fuel efficiency of internal combustion engine, to prevent corrosion of gas transportation system, and to cope with climate change preemptively. In recent years, there has been a growing interest in not only conventional membrane-based separation but also new adsorbent-based separation technology. Particularly, in the case of metal-organic frameworks (MOFs), it has been received tremendous attentions due to its unique properties (eg : flexibility, gate effect or strong binding site such as open metal sites) which are different from those of typical porous adsorbents. Therefore, in this study, stereotype of two MOFs have been selected as its flexible MOFs (MIL-53) representative and numerous open metal sites MOFs (MOF-74) representative, and compared each other for $CO_2/CH_4$ separation performance. Furthermore, varying and changeable separation performance conditions depending on the temperature, pressure or samples' unique properties are discussed.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.644-651
• /
• 2011

Storing hydrogen in solid state hydride is one of the best promising methods for the future hydrogen economy. The total performance of such systems depends on the rate at which the amount of mass and heat migration is supplied to solid hydride. Therefore, an accurate modeling of the heat and mass transfer is of prime importance in optimizing the design of such systems. In this work, Hydrogen storage in Pt-CNTs hydrogen reactor has been intensively investigated by solving 2 dimensional mathematical models. Using a CFD computer software, systematic studies have been performed to elucidate the effect of heat and mass transfer during hydrogen charging periods. It was revealed that the optimized design of hydrogen storage vessel can prevent the increase of system temperature and the charging time due to the convective cooling effects inside the vessels at even high charging pressure. Because none has reported the critical issues of heat and mass transfer for CNT based hydrogen storage system, this work can support the first insight of the optimal design for solid state hydrogen storage system based on CNT in the near future.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.5
• /
• pp.353-362
• /
• 2016

Thermal barrier coating (TBC) is an essential element consisting of a super-alloy base and ceramic coating designed to achieve long operational time under a high temperature and pressure environment. However, the top coat of TBC can be delaminated at certain temperatures with long operation time. As the delamination of TBC is directly related to the blade damage, the coupling status of the TBC should be assured for reliable operation. Conventional studies of nondestructive evaluation have been made for detecting generation of thermally grown oxide (TGO) or qualitatively evaluating delamination in TBC. In this study, the ultrasonic C-scan method was developed to obtain the damage map inside TBC by estimating the delamination in a quantitative way. All specimens were isothermally degraded at $1,100^{\circ}C$ with different time, having different partial delamination area. To detect partial delamination in TBC, the C-scan was performed by a single transducer using pulse-echo method with normal incidence. Partial delamination coefficients of 1 mm to 6 mm were derived by the proportion of the surface reflection signal and flaw signal which were theoretical signals using Rogers-Van Buren and Kim's equations. Using the partial delamination coefficients, the partial delamination maps were obtained. Regardless of the partial delamination coefficient, partial delamination area was increased when degradation time was increased in TBC. In addition, a decrease in partial delamination area in each TBC specimen was observed when the partial delamination coefficient was increased. From the portion of the partial delamination maps, the criterion for delamination was derived.

• Journal of the Korean earth science society
• /
• v.25 no.6
• /
• pp.443-473
• /
• 2004

In northern Gohung granitic gneiss, porphyroblastic gneiss and migmatitic gneiss are widely distributed. Gneisses were plotted in granodiorite domain on an lUGS silica-alkali diagram. The amounts of trace elements (Li, Zn, Sc, Sr, Ni, V Y etc.) vs. $SiO_2$, somewhat decreased. Plagioclase showed a wide compositional range ($An_{32-48}$). $X_{alm}$ and $X_{sps}$ were higher in garnet rim and $X_{pyp}$ in garnet core. The rocks in the study area were formed from S and I-type magmas which generated from syn-collision and the late to post-orogenic tectonic environment. Metamorphic P-T conditions u·ere low to medium pressure, high temperature (803-913$^{\circ}C$, 6.1-7.3 kb) and overprinted by retrograde metamorphism (570-726$^{\circ}C$, 2.2-5.1 kb) and chloritization.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.11
• /
• pp.1701-1708
• /
• 2014

Phenolic compounds, physiological properties, and digestive enzyme inhibitory effect of 70% ethanol extracts from Aster scaber with different extraction methods (stirrer extraction, SE; reflux extraction, RE; autoclave extraction, AE; low temperature high pressure extraction, LTPE; ultrasonification extraction, USE) were investigated. Total polyphenols and flavonoids contents in LTPE were significantly higher than those of other extracts. The amount of substances related to cynarin (1,3-O-dicaffeoylquinic acid) was highest in USE (34.34 mg/g), followed by LTPE (33.83 mg/g), RE (32.27 mg/g), AE (25.40 mg/g), and SE (18.17 mg/g). Chlorogenic acid (5-O-caffeoylquinic acid) and astragalin (kaempferol-3-O-glucopyranoside) were highest in AE and LTPE, respectively. Xanthine oxidase, angiotensin- I converting enzyme, 3-hydroxy-3-methylglutaryl coenzyme A reductase and acetylcholin esterase inhibitory activities of LTPE and USE at a concentration of 50 mg% (w/v) were somewhat higher than those of other extracts. The ${\alpha}$-amylase, ${\alpha}$-glucosidase, trypsin and lipase activities showed the same tendency as physiological properties (concentration of 500 mg%, w/v). Additionally, there was significantly higher or slightly lower inhibitory activity compared to the control group. These results suggest that extracts from Aster scaber have potential to act as functional materials, and LTPE and USE are superior for the enhancement of biological activity.

• The Korean Journal of Nuclear Medicine
• /
• v.25 no.2
• /
• pp.286-293
• /
• 1991

$^{123}I$, which is applied for the thyroid and other in vivo kinetic study, has a special role in life sciences. The 159 KeV $\gamma-ray$ from $^{123}I$ is almost ideally appropriate for the current imaging instrumentation. Its decay mode (electron capture) and short half-life (13.3 hr) reduced the burden of radiation dose to the patients, and its chemical property makes it easy to synthesize the labelling compounds. In this experiment, the production of $^{123}I$ via the nuclear reaction $^{124}Te(p,2n)^{123}I$ with 28 MeV protons was sutdied. $TeO_2$ is used as a target material, because it has good physical properties. The target was prepared with $TeO_2$ powder and was molten into a ellipsoidal cavity (a=14 mm, b=10 mm, $270.8mg/cm^2$ thick) of pure platinum. The irradiation was carried out in the external proton beam with incident energies range from 28 MeV to 22 MeV, and current was $30{\mu}A$. The loss of $TeO_2$ target was significantly reduced by using $4\pi-cooling$ system in irradiation. The dry distillation method was adopted for the separation of $^{123}I$ from irradiated target, and when it was kept 5 minutes at $780^{\circ}C$, its result was quantitative. The loss of the target material $(TeO_2)$ was below 0.2% for each production run and $^{123}I$ from the dry distillation apparatus was captured with 0.01 N NaOH in $Na^{123}I$ form, then the pH of the solution was adjusted to $7.5\sim9.0$ with HC1/NaOH. The $Na^{123}I$ solution was passed through $0.2{\mu}m$ membrane filter, and sterilized under high pressure and temperature for 30 minutes. The production of $^{123}I$ is acceptable for clinical application based on the quality of USP XXI.