• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.100-106
• /
• 2006

The behavior of spray impinging on the inclined constant temperature flat plate was experimentally investigated. To clarify the wall effect of a high pressure DISI injector, a relative angle of the inclined wall to a spray axis was varied. Spray penetration along the wall was observed optically and it was compared with that of a Fan spray type and Swirl type spray. To evaluate various spray motion quantitatively, a spray path penetration which describe the development of a spray tip along the wall was newly introduced. To observe the structure of an impinging spray, it was visualized by a controlled stroboscope light and its visualized image was captured on an CCD camera. Using the digital image of impinging spray $H_x$ and $R_x$ was extracted to clarify the structure of impinging spray. The main parameter of the relative position of the wall was the inclined angle which was defined as the angle was varied from $0^{\circ}$ (vertical impingement) to $60^{\circ}$ at the same condition.

• Economic and Environmental Geology
• /
• v.22 no.3
• /
• pp.237-252
• /
• 1989

The Inseong gold-silver mine is located 3Km northwest of Suanbo, Choongcheongbugdo, Republic of Korea. The mine occurs in the shear zone formed by tension fractures within the Hwanggangri Formation of the Ogcheon metamorphic belt. Ore minerals found in the gold-silver bearing hydrothermal quartz vein composed mainly of pyrite, arsenopyrite, sphalerite, galena and minor amount of chalcopyrite, pyrrhotite, stannite, bismuthininte, native bismuth, chalcocite, electrum and tellurian canfieldite(?). The gangue minerals are quartz, calcite, chlorite and rhodochrocite. Wallrock alterations such as chloritization, silicitication, pyritization, carbonitization and sericitization can be observed in or around the quartz vein. According to the paragenetic sequence, quartz vein structure and mineral assemnlages, three different stages of ore formation can be recognized. The physico-chemical environment of ore formation in this deposit shows slight variation from stage to stage, but the condition of main ore deposition can be summarized as follows. Fluid inclusion, S-istope geothermometry and geothermometry based on mineral chemistry by use of arsenopyrite and chlorite show the ore was formed at temperature between 399 and $210^{\circ}C$ from fluids with salinities of 3.3-5.8 wt.% equivalent NaCl. It indicates that pressure during the mineralization is less than 0.6 Kb corresponding to a depth not greater than 1Km. S-isotope data suggests that thermal fluid may have magmatic origin wit some degree of mixing with meteoric water. In coclusion, the Inseong gold-silver deposit was formed at shallow depth and relatively high-temperature possibly with steep geothermal gradient under xenothermal condition.

• Food Science and Biotechnology
• /
• v.16 no.6
• /
• pp.928-934
• /
• 2007

Physiochemical properties, such as yield and molecular weight distribution of polysaccharide fractions, of polysaccharides in the enzymatic hydrolysates of purslane were investigated and characterized. A higher amount of micro nutrients, such as potassium (9,413 mg/100 g), phosphorus acid (539 mg/100 g), leucine, alanine, lysine, valine, glycine, and isoleucine, was present in whole purslane. The yield of water soluble polysaccharides (WSP) was 0.29, 7.01, and 7.94% when extracted using room temperature water (RTW), hot-water (HW), and hot temperature/high pressure-water (HTPW), respectively, indicating that HW or HTPW extraction may be effective to obtain WSP from purslane. The average ratio of L-arabinose:D-galactose in the WSP was 37:49, 34:37, and 27:29, when extracted using RTW, HW, and HTPW, respectively. These results indicate that water was a suitable extraction solvent for preparation of the arabinogalactan component of whole purslane. A higher yield and total carbohydrate content was obtained by using Viscozyme L instead of Pectinex 5XL during extraction of the WSP, which indicates that enzymatic treatment of purslane may be an effective method to control the Mw of polysaccharides. Finally, it was confirmed that Viscozyme L is a suitable enzyme for the hydrolysis and separation of polysaccharides obtained from purslane.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.6
• /
• pp.84-91
• /
• 2002

Temperature distribution in the GTD111 turbine blade used in power plaints is calculated by heat transfer analysis. Linear stress analysis of the turbine blade is also carried out under thermal loads and centrifugal forces. The numerical results of steady state heat transfer analysis slow that high temperature distribution occurs at the leading edge and tip section of the blade. The thermal stress result indicates that the equivalent stress at the tip of the pressure surface is higher than other sections of the blade. Maximum centrifugal stresses without the thermal effect occurs at the front of the fir tree. From the thermal-centrifugal stress analysis, maximum equivalent stress occurs at the fir tree. Stresses applied by the thermal loads and centrifugal forces are less than the yield stress. The GTD111 turbine blade is safe to be used in the power plants.

• Journal of Korea Foundry Society
• /
• v.21 no.4
• /
• pp.253-259
• /
• 2001

There are many methods to produce metal foams, which can be classified into three groups according to the state of the starting metal i.e. liquid or powder or solid. Three types of defects such as cell closing, cell deformation or breakdown and cell misrun are thought to be occurred when we make the open cell aluminum foams by precision casting. Filling ability of the mold slurry between preform is related with cell closing, mold collapsibility is related with cell deformation or breakdown, mold temperature and pouring pressure are related with cell misrun. These factors can be evaluated by measuring slurry fluidity, burnout strength and permeability of the mold. Properties of the plaster mold were evaluated to find optimum mold conditions for high quality open cell aluminum foam in this study. Permeability was almost zero independent of burnout conditions, however, crack initiation was found on the surface of all specimens one or two minutes after taking out from the furnace. Crack has grown and disappeared with time. This crack may facilitate the mold filling when molten metal is poured, because of the improved mold permeability. It was considered that crack initiation and disappearance was closely related with temperature difference between the surface and inner part. Knocking-out the mold is a difficult problem due to the small cell size, because continuous mesh structure of the metal foam is not strong. It is not easy to remove molding material after pouring. We can expect that water quenching can facilitate the knocking-out the mold after solidification without damaging cell structures. Collapsed particles after water quenching became bigger with the increase in time.

• Journal of the Korean Magnetics Society
• /
• v.6 no.5
• /
• pp.317-322
• /
• 1996

Thin films of Fe-Zr-N were fabricated by rf magnetron reactive sputtering method. The saturation magnetization and coercivity as functions of annealing temperature and partial pressure of nitrogen gas, effective permeability at high frequencies, and thermal stability were investigated. Magnetic softness was exhibited in the composition range of $Fe_{72-78}Zr_{7-10}N_{15-18}$ which was boundary between polycrystalline and amorphous structure. These films exhibited magnetic softness with saturation magentic flux density of 1.55 T and effective permeability of about 3000 at 1 MHz. These films also exhibited thermal stability by sustaining effective permeability of 2500 or above as the temperature was raised to $550^{\circ}C$. It is asswned that good magnetic softness is obtained because grain growth of $\alpha-Fe$ is prohibited due to the precipitation of ZrN nanocrystals. The grain sizes of $\alpha-Fe$ films were $40~50\AA$ and the grain sizes of ZrN nanocrystals were $10~15\AA$.

• Korean Journal of Materials Research
• /
• v.27 no.7
• /
• pp.386-391
• /
• 2017

Using a customized diffusion bonder, we executed diffusion bonding for ring shaped white gold and red gold samples (inner, outer diameter, and thickness were 15.7, 18.7, and 3.0 mm, respectively) at a temperature of $780^{\circ}C$ and applied pressure of 2300 N in a vacuum of $5{\times}10^{-2}$ torr for 180 seconds. Optical microscopy, field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to investigate the microstructure and compositional changes. The mechanical properties were confirmed by Vickers hardness and shear strength tests. Optical microscopy and FE-SEM confirmed the uniform bonding interface, which was without defects such as micro pores. EDS mapping analysis confirmed that each gold alloy was 14K with the intended composition; Ni and Cu was included as coloring metals in the white and red gold alloys, respectively. The effective diffusion coefficient was estimated based on EDS line scanning. Individual values of Ni and Cu were $5.0{\times}10^{-8}cm^2/s$ and $8.9{\times}10^{-8}cm^2/s$, respectively. These values were as large as those of the melting points due to the accelerated diffusion in this customized diffusion bonder. Vickers hardness results showed that the hardness values of white gold and red gold were 127.83 and 103.04, respectively, due to solid solution strengthening. In addition, the value at the interface indicated no formation of intermetallic compound around the bonding interface. From the shear strength test, the sample was found not to be destroyed at up to 100,000 gf due to the high bonding strength. Therefore, these results confirm the successful diffusion bonding of 14K white-red golds with a diffusion bonder at a low temperature of $780^{\circ}C$ and a short processing time of 180 seconds.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1055-1061
• /
• 1999

Indium Tin Oxide (ITO) films were fabricated by vacuum deposition technique and their microwave shielding properties were investigated for the application to the transparent shield material. The vacuum coating was conducted in a RF co-sputtering machine. The film composition and structure associated with the sputtering conditions (argon and oxygen pressure. substrate temperature. RF input power) were investigated for the attainment of high electrical conductivity and good transparency. The electrical conductivity of IT0 films fabricated under the optimum deposition conditions (substrate temperature : $300^{\circ}C$. Ar flow rate : 20 sccm, Oxygen flow rate : 10 sccm, In/Sn input power : 50/30 W) showed 5.6$\times10^4$mho/m. The optical transparency is also considerably good. The microwave shielding properties including the dominant shielding mechanism are investigated from the electrical conductivity, thickness and skin depth of the ITO films. The total shielding effectiveness is then estimated to be 26 dB, which provides a suggestion that the IT0 films can be effectively used as the transparent shield material.

• Korean Journal of Food Science and Technology
• /
• v.25 no.3
• /
• pp.288-294
• /
• 1993

Solubilities of urea-crystallized tuna oil methyl esters in supercritical carbon dioxide were determined by a flow through extraction reactor. Experimental results obtained under a quasi-equlibrium condition showed that at 150 bar, solubilities of the esters in supercritical $CO_2$ were 0.075, 0.028 and 0.006(w/w) at $40^{\circ}C,\;60^{\circ}C\;and\;80^{\circ}C$, respectively. In the pressure and temperature ranges $(100{\sim}200bar\;and\;40{\sim}80^{\circ}C)$, the solubility increased with the density of $CO_2$. However, selectivity of supercritical carbon dioxide on the extracted compounds was much better at low density than at high density. Supercritical fractionation with a temperature gradient $(50{\sim}75^{\circ}C)$ resulted in concentrates of EPA and DHA in purities of 12% and 85%, respectively.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.551-556
• /
• 2013

AlN films with c-axis orientation and thermal conductivity characteristics were deposited by using Pulsed Laser Deposition and the films were characterized by changing the deposition conditions. In particular, we investigated the optimal conditions for the application of a heat sinking plane AlN thin film. Epitaxial AlN films were deposited on sapphire ($c-Al_2O_3$) single crystals by pulsed laser deposition (PLD) with an AlN target. AlN films were deposited at a fixed pressure of $2{\times}10^{-5}$ Torr, while the substrate temperature was varied from 500 to $700^{\circ}C$. According to the experimental results of the growth temperature of the thin film, AlN thin films were confirmed with a highly c-axis orientation, maximum grain size, and high thermal conductivity at $650^{\circ}C$. The thermal conductivity of the AlN thin film was found to increase compared to bulk AlN near the band gap value of 6.2 eV.