• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.1
• /
• pp.56-62
• /
• 2003

The objective of this study is to adjust the roll gap for the dimension accuracy of bar in hot bar rolling process considering roll wear. In this study hot bar rolling processes for round and oval passes have been investigated. In order to predict the roll wear, the wear model is reformulated as an incremental form and then wear depth of roll is calculated at each deformation step on contact area using the results of finite element analysis, such as relative sliding velocity and normal pressure at contact area. Archard's wear model was applied to predict the roll wear. To know the effects of thermal softening of DCI (Ductile Cast Iron) roll material according to operating conditions, high temperature micro hardness test is executed and a new wear model has been proposed by considering the thermal softening of DCI roll expressed in terms of the main tempering curve. The new technique developed in this study for adjusting roll gap can give more systematically and economically feasible means to improve the dimension accuracy of bar with full usefulness and generality.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.867-870
• /
• 2009

일반적으로 내화재의 내침식성은 크롬 함량이 증가함에 따라 향상되는 특성을 가지는데, 본 연구에서는 이러한 크롬 내화재의 물성을 보다 향상시키기 위하여 인산염 화합물인 $AlPO_4$를 첨가하는 실험을 진행하였으며, 이러한 실험 결과 선정된 $AlPO_4$ 1% 첨가 크롬 내화재를 대상으로 캐스타블 및 브릭 형태로 각각 제작하였을 때 내침식 특성에 대해 회전 침식 시험장치를 이용한 실험을 실시하였는데, 실험 결과 캐스타블에 비해 브릭 내화재가 내침식성이 우수하지만 일부 spalling이 발생하는 것으로 파악되었다. 그리고, 가스화기로의 석탄 공급 방식에 따라 내화재 벽면에서 발생하는 석탄입자에 의한 내화재 침식 정도에 대한 전산해석을 수행한 결과 top feeding에 비해 side feeding 방식이 내화재 전면에 걸쳐 침식 현상이 크게 발생할 것으로 예측되어 보다 크롬 함량이 많은 내화재를 선정해야 할 것으로 평가되었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.98.2-98.2
• /
• 2011

For optimal performance of a proton exchange membrane fuel cell (PEMFC), the membrane electrode assembly (MEA) requires hydration, and the membrane's conductivity depends on water content. A humidifier is required to ensure that the reactant gas, usually hydrogen and air, is hydrated before entering the fuel cell. Dry membrane operation or improper hydration causes performance degradation. Typically, the humidification of a fuel cell is carried out by means of an internal or external humidifier. A membrane humidifier is applied to the external humidification of transportation or residential power generation fuel cell due to its convenience and high performance. In this study, The experiments were constructed with a plate-type membrane humidifier in terms of geometric parameters and operating parameters. The results show that the temperature and pressure, the channel length, the membrane thickness and gas flow rate are critical parameters affecting the performance of the humidifier.

• Korean Journal of Organic Agriculture
• /
• v.10 no.1
• /
• pp.35-47
• /
• 2002

In swine production, efficiency of utilization of nutrients is imperative. By embracing advances in processing techniques(i.e., fine grinding, pelleting, steam flaking, roasting, extrusion and expanding) nutrient utilization of feeds turfs have greatly improved. Grinding is by far the most commonly used process with reduction of particle size, Expander, like extruders, are high-temperature and pressure-short-term processor. The purpose of using an expander is to improve pellet quality. Also, expanding of dietary ingredients indicates improvements in growth performance and nutrient digestibility. Because feed cost are easily the greatest economic input into swine production, maximizing nutrient utilization is an area that will continue to receive much attention. Therefore, much attention will continue to be placed on feed processing techniques that will give consistent improvements in animal performance and nutrient digestibility.

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.245-250
• /
• 1996

$Y_2O_3$ thin film on si(100) was successfully grown by ionized cluster beam(ICBD) technique at substrate temperature of around $500^{\circ}C$ and pressure of ~$10^{-5}$Torr.To prevent the oxidation of Si substrae, a very thin yttrium layer was deposited on Si before reactive depositing of oxygen and yttrium source. In asdeposited stage, b.c.c and h.c.p strucutres of $Y_2O_3$ were observed from S-ary analysis. From the observation of spots and ring patterns in selected area diffractin(SAD) patterns. crystallane formation and growth could be proceeded during the deposition. $Y_2O_3$/mixed layer/$SiO_2=170\AA/50\AA/10\AA$ structure were verified by high resolution transmition electron imcroscopy(HRTEM) image, and the formation of amorphous layer of SiO2 was discussed . Electricla charateristics of the film were also investigated . In as-deposited Pt/$Y_2O_3$/Si sturcuture, leakage current was less than $10^{-6}$A/$\textrm{cm}^2$ at 7MV/cm strength.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.5
• /
• pp.1022-1030
• /
• 2004

The gene encoding Aquifex pyrophilus (Apy) DNA polymerase was cloned and sequenced. The Apy DNA polymerase gene consists of 1,725 bp coding for a protein with 574 amino acid residues. The deduced amino acid sequence of Apy DNA. polymerase showed a high sequence homology to Escherichia coli DNA polymerase I-like DNA polymerases. It was deduced by amino acid sequence alignment that Apy DNA polymerase, like the Klenow fragment, has only the two domains, the $3'{\rightarrow}5'$ exonuclease domain and the $5'{\rightarrow}3'$ polymerase domain, containing the characteristic motifs. The Apy DNA polymerase gene was expressed under the control of T7lac promoter on the expression vector pET-22b(+) in E. coli. The expressed enzyme was purified by heat treatment, and Cibacron blue 3GA and $UNO^{TM}$ Q column chromatographies. The optimum pH of the purified enzyme was 7.5, and the optimal concentrations of KCl and $Mg^{2+}$ were 20 mM and 3 mM, respectively. Apy DNA polymerase contained a double strand-dependent $3'{\rightarrow}5'$ proofreading exonuclease activity, but lacked any detectable $5'{\rightarrow}3'$ exonuclease activity, which is consistent with its amino acid sequence. The somewhat lower thermostability of Apy DNA polymerase than the growth temperature of A. pyrophilus was analyzed by the comparison of amino acid composition and pressure effect.

• Journal of the Korean Society of Combustion
• /
• v.3 no.1
• /
• pp.59-69
• /
• 1998

The results of study on the active control of naturally occurring combustion oscillations with a single dominant frequency in an atmospheric dump combustor are presented. Control was achieved by an oscillatory infection of secondary fuel at the dump plane. A high speed solenoid valve with a maximum frequency of 250Hz was used as the actuator and a sound level meter, located at the combustor exit, measured the pressure fluctuations which served as the feedback signal for the control loop. Instability characteristics were mapped over a range of mean mixing section velocities from 6.7 m/s-9.3 m/s and with three mixing conditions. Different fuel/air mixing conditions were investigated by introducing varying percentages of primary fuel at two locations, one at the entrance to the mixing section and one 6 mixing tube diameters upstream of the dump plane. Control studies were conducted at a mean velocity of 9.3 m/s, with an air temperature of $415^{\circ}C$, and from flame blowout to the stoichiometric condition.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.5
• /
• pp.1017-1022
• /
• 2011

This paper describes the improvement of the calculation by using $6{\sigma}$ method on steam turbine simulator in a nuclear power plant. The simulator is essential to not only verification and validation of control logic but also making sure of control constants in upgrading the long time used control system into the new one. And the dynamic model is a key point in that simulator. The model used during the retrofit period of the turbine controller in Kori Nuclear Power Plant makes difference in calculating generator output and control valve positions. That is because such operating data as the main steam pressure, the main steam temperature and control valve positions of Yongkwang #3 are different from those of Kori #4. Therefore, the model parameters must be tuned by using actual operating data for the high fidelity of simulator in calculating the dynamic characteristic of the model. This paper describes that the $6{\sigma}$ method is used in improvement of precision of generator output calculation in the steam turbine model of the simulator.

• Journal of the Korean Society of Safety
• /
• v.27 no.1
• /
• pp.63-69
• /
• 2012

Ready-mixed concrete(RMC) has been a major construction materials for infrastructures. However, RMC with poor quality is reported to be social issue since it directly user's safety and convenience. Because the properties of concrete as a construction material are greatly influenced by the variation of water content, to control water accurately is the most efficient method for the quality control in RMC industry. In this study, the automatic measurement technology of fine aggregate was developed by using the microwave moisture measurement. For the various conditions of fine aggregate such as moisture, temperature and pressure, the calibration curve of moisture measurement was obtained by using oven-dry method. From the infield and outfield test, it can be obtained that the accuracy of microwave moisture measurement is very high and the automatic system of microwave moisture measurement is very convenient and useful for quality control in RMC Industry.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.2
• /
• pp.139-148
• /
• 2002

Both UV Photolysis and Phtocatalytic Oxidation Processing are an emerging technology for the abatemant of Volatile Organic Compounds (VOCs) in atmospheric -pressure air streams. However, each process has some drawbacks of their own. The former is little known as an application for air pollution treatment, so it has been a rare choice in the field. Therefore we have to do more experiment and study for its application for treatment of VOCs. Although the latter has been used in the industrial fields, it still has a difficulty in decomposing high concentrations of VOCs. To solute these problems, we have been studying simultaneous application of those two technologies. We have studied the effects of background gas composition and gas temperature on the decomposition chemistry. It has shown that concentration of TCE and B.T.X., diameter of reactor, and wavelength of lamp have effects on decomposition efficiency. When using Photolysis Process only, the rates of fractional conversion of each material are found at TCE 79%, Benzene 65%, Toluene 68%, Xylene 76%. In case of Photocatalytic Oxidation Process only, the rates of fractional conversion decreased drastically above 30 ppm. When there two methods were combined, the rates of fractional conversion of each material are enhanced such as TCE 93%, Benzene 75%, Toluene 81%, Xylene 90%. Therefore, we conclude that the combination of Photolysis-Photocatalytic Oxidation process is more efficient than each individual process.