• The KSFM Journal of Fluid Machinery
• /
• v.19 no.2
• /
• pp.5-10
• /
• 2016

Gas flow measurement in a closed duct was performed using multi-point Pitot tubes. Measurement uncertainty was assessed for this measurement method. The method was applied for the measurement of air flow into a gas turbine engine in an altitude engine test facility. 46 Pitot tubes, 15 total temperature Kiel probes and 9 static pressure tabs were installed in the engine inlet duct of inner diameter of 264 mm. Five tests were done in an airflow range of 2~10 kg/s. The flow was compressible and the Reynolds numbers were between 450,000 and 2,220,000. The measurement uncertainty was the highest as 6.1% for the lowest flow rate, and lowest as 0.8% for the highest flow rate. This is because the difference between the total and static pressures, which is also related to the flow velocity, becomes almost zero for low flow rate cases. It was found that this measurement method can be used only when the flow velocity is relatively high, e.g., 50 m/s. Static pressure was the most influencing parameter on the flow rate measurement uncertainty. Temperature measurement uncertainty was not very important. Measurement of boundary layer was found to be important for this type of flow rate measurement method. But measurement of flow non-uniformity was not very important provided that the non-uniformity has random behavior in the duct.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.2
• /
• pp.147-152
• /
• 2014

In this research, polysulfone hollow fiber membrane was used to recover $CO_2$ which is one of greenhouse gases from flue gas stream being emitted after the combustion of fossil fuels. The prerequisite requirement is to design the membrane process producing high-purity $CO_2$ from flue gas. For separation of $CO_2$, a membrane module and flue gas containing 10% carbon dioxide was used. The effects of operating conditions such as pressure, temperature, feed gas composition and multi-stage membrane on separation performance were examined at various stage cuts. Higher operating pressure and temperature increased carbon dioxide concentration and recovery ratio in permeate. Recovery ratio and separation efficiency increased if a higher content of $CO_2$ injection gas composition. Three-stage membrane system was producing a 95% $CO_2$ with 90% recovery from flue gas. The separation efficiency of three-stage membrane system was higher than one-stage system.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1210-1215
• /
• 1999

Optimum conditions of the hydrogenation of PNA to pure PPD were determined in a three-phase slurry reactor with suspended Pd/C catalyst particles. Minimization of mass transfer resistances at the interfaces of both gas-liquid and liquid-catalyst particles and control of overall reaction rate on catalyst surface leaded to decrease the hydrogen starvation on reaction active sites and to reduce the side reactions during hydrogenation. The optimum temperature, pressure, and catalysst concentration were confirmed to be in the range of $60^{\circ}C$, 60~70 psig, and 1~2 g-cat/L, respectively. Reaction rate was zero order with respect to the concentration of PNA and 1st order with respect to the pressure of hydrogen(P). Overall rate expression of the reaction was $R_A=6.44{\times}10^6{\cdot}H{\cdot}P{\cdot}m{\cdot}$exp(-4659/T) where H is constant, m is concentration of catalyst, and T is temperature.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.4
• /
• pp.266-273
• /
• 2008

Natural gas hydrates are ice-like solid substances, which are composed of water and natural gas, mainly methane. They have three kinds of crystal structures of five polyhedra formed by hydrogen-bonded water molecules, and are stable at high pressures and low temperatures. They contain large amounts of organic carbon and widely occur in deep oceans and permafrost regions. Therefore, they are expected as a potential energy resource in the future. Especially, $1m^3$ natural gas hydrate contains up to $172Nm^3$ of methane gas, de pending on the pressure and temperature of production. Such large volumes make natural gas hydrates can be used to store and transport natural gas. In this study, three-phase equilibrium conditions for forming natural gas hydrate were numerically obtained in pure water and single electrolyte solution containing 3 wt% NaCl. The results show that the predictions match the previous experimental values very well, and it was found that NaCl acts as an inhibitor. Also, help gases such that ethane, propane, i-butane, and n-butane reduce the hydrate formation pressure at the same temperature.

• Food Science and Preservation
• /
• v.24 no.5
• /
• pp.559-564
• /
• 2017

Yogurt contains many microorganisms that are beneficial to human health, and is a probiotic that supplies many nutrients such as calcium and protein. It is difficult to safety preserve for a long time because it possesses a high content of water. To address this problem, powdered "instant" yogurt has been developed, but it has flaws low flowability and solubility. Therefore, yogurt was granulated using a fluidized bed granulator to increase flowability and solubility. The fluidized bed granulator was designed by using response surface methodology (RSM), whose variables were feeding rate (FR), atomization air pressure (AP) and product temperature (PT). After being granulated, the yogurt was analyzed for yield and lactic acid bacteria count. The maximum yield of yogurt granules was 79.42%, at FR of 0.54 mL/min, AP of 2.64 kPa, and PT of $58.18^{\circ}C$, and the colony count for lactic acid bacteria was more than $6log^{10}\;CFU/g$. Therefore, spherical granulation of yogurt using a fluidized bed granulator could be used for making convenient probiotic products with improved flowability and solubility.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.489-494
• /
• 2004

Long Period Gratings (LPG) is currently receiving considerable attention because of their consistent measuring results fur pressure, temperature, strain and flow. LPG is easier to prepare and has a high sensitivity compared with Fiber Bragg Gratings (FBG). In addition, this kind of optical fiber sensors could be used for implementations in various structures. In this paper, LPG was used to monitor in situ the resin flow and the curing process in VARTM (Vacuum Assisted Resin Transfer. Molding). In order to demonstrate the effectiveness of the method, FBG is inserted into the glass mat to monitor the resin flow using optical spectrum analyzer (OSA). The curing reactions in VARTM are also observed using the same method. From the results, the attenuation wavelength shift and the loss change of attenuation band can be obtained from the status of the RTM (Resin Transfer Molding) sample owing to the internal variations of the .effective index, temperature, and pressure. It is shown that the proposed LPG is more effective in monitoring the curing reaction than FBG.

• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.282-287
• /
• 1998

Dependence of magnetoresistance on base pressure and deposition rates of each Fe, Co, Cu layers in the $Fe(50{\AA}/[Co(17{\AA})/Cu(24{\AA})]_20$ multilayer thin films, prepared by dc magnetron sputtering on Corning glass, were investigated. AFM analysis, X-ray diffraction analysis, vibrating sample magnetometer analysis, and magnetoresustance measurement (4-probe method) were performed. The multilayer films deposited under low base pressure increases magnetoresistance ratio by preventing oxidation. Annealing for the samples at a moderate temperature allowed larger textured grain with no loss in the periodicity. Magnetoresistance ratio of the annealed multilayers was increased due to the increase antiferromagnetically coupled fraction of the film after annealing. Optimization of deposition rate was greater than 1 $\AA$/s for Fe, and 2.8 $\AA$/s for Cu. Deposition rate of Co showed a tendency of increasing of magnetoresistance ratio due to the formation of flat magnetic layer in case of high deposition rate of Co.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2325-2332
• /
• 2012

A series $[C_3Omim]$[X] of imidazolium cation-based ILs, with ether functional group on the alkyl side-chain have been synthesized and structure of the materials were confirmed by various techniques like $^1H$, $^{13}C$ NMR spectroscopy, MS-ESI, FTIR spectroscopy and EA. More specifically, the influence of changing the anion with same cation is carried out. The absorption capacity of $CO_2$ for ILs were evaluated at 30 and $50^{\circ}C$ at ambient pressure (0-1.6 bar). Ether functionalized ILs shows significantly high absorption capacity for $CO_2$. In general, the $CO_2$ absorption capacity of ILs increased with a rise in pressure and decreased when temperature was raised. The obtained results showed that absorption capacity reached about 0.9 mol $CO_2$ per mol of IL at $30^{\circ}C$. The most probable mechanism of interaction of $CO_2$ with ILs were investigated using FTIR spectroscopy, $^{13}C$ NMR spectroscopy and result shows that the absorption of $CO_2$ in ether functionalized ILs is a chemical process. The $CO_2$ absorption results and detailed study indicates the predominance of 1:1 mechanism, where the $CO_2$ reacts with one IL to form a carbamic acid. The $CO_2$ absorption capacity of ILs for different anions follows the trend: $BF_4$ < DCA < $PF_6$ < TfO < $Tf_2N$. Moreover, the as-synthesized ILs is selective, thermally stable, long life operational and can be recycled at a temperature of $70^{\circ}C$ or under vacuum and can be used repeatedly.

• Journal of Ginseng Research
• /
• v.44 no.2
• /
• pp.229-237
• /
• 2020

Background: We investigated the tolerability and pharmacokinetic properties of various ginsenosides, including Rb1, Rb2, Rc, Rd, and compound K, after single or multiple administrations of red ginseng extract in human beings. Methods: Red ginseng extract (dried ginseng > 60%) was administered once and repeatedly for 15 days to 15 healthy Korean people. After single and repeated administration of red ginsengextract, blood sample collection, measurement of blood pressure and body temperature, and routine laboratory test were conducted over 48-h test periods. Results: Repeated administration of high-dose red ginseng for 15 days was well tolerated and did not produce significant changes in body temperature or blood pressure. The plasma concentrations of Rb1, Rb2, and Rc were stable and showed similar area under the plasma concentration-time curve (AUC) values after 15 days of repeated administration. Their AUC values after repeated administration of red ginseng extract for 15 days accumulated 4.5- to 6.7-fold compared with single-dose AUC. However, the plasma concentrations of Rd and compound K showed large interindividual variations but correlated well between AUC of Rd and compound K. Compound K did not accumulate after 15 days of repeated administration of red ginseng extract. Conclusion: A good correlation between the AUC values of Rd and compound K might be the result of intestinal biotransformation of Rb1, Rb2, and Rc to Rd and subsequently to compound K, rather than the intestinal permeability of these ginsenosides. A strategy to increase biotransformation or reduce metabolic intersubject variability may increase the plasma concentrations of Rd and compound K.

• Archives of Pharmacal Research
• /
• v.28 no.7
• /
• pp.866-874
• /
• 2005

The objective of this study was to elucidate the feasibility to improve the solubility and bioavailability of poorly water-soluble itraconazole via solid dispersions by using supercritical fluid (SCF). Solid dispersions of itraconazole with hydrophilic polymer, HPMC 2910, were prepared by the aerosol solvent extraction system (ASES) under different process conditions of temperature/pressure. The particle size of solid dispersions ranged from 100 to 500 nm. The equilibrium solubility increased with decrease (15 to 10 MPa) in pressure and increase (40 to $60^{\circ}C$) in temperature. The solid dispersions prepared at $60^{\circ}C$/15 MPa showed a slight increase in equilibrium solubility (approximately 27-fold increase) when compared to pure itraconazole, while those prepared at $60^{\circ}C$/10MPa showed approximately 610-fold increase and no endothermic peaks corresponding to pure itraconazole were observed, indicating that itraconazole might be molecularly dispersed in HPMC 2910 in the amorphous form. The amorphous state of itraconazole was confirmed by DSC/XRD data. The pharmacokinetic parameters of the ASES-processed solid dispersions, such as $T_{max},\;C_{max},\;and\;AUC_{0-24h}$ were almost similar to $Sporanox_{\circledR}$ capsule which shows high bioavailability. Hence, it was concluded that the ASES process could be a promising technique to reduce particle size and/or prepare amorphous solid dispersion of drugs in order to improve the solubility and bioavailability of poorly water-soluble drugs.