• Journal of the korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.28-41
• /
• 1979

Propane-Air premixed combustible gas was ignited by the conventional current break system inside the open combustion chamber under the atmospheric pressure and the room temperature to measure the flame propagating speed and the burning speed, also to elucidate the history of the propagating flame behavior and wall effects to flame shape by using Ion Gap Method and High Speed Schlieren Photography. The results obtained show that the maximum flame propagating speed and maximum burning speed are approximately 292 cm/sec and 36 cm/sec at the mixture ratio 4.6%, respectively. The cellular flame structures can be observable in the rich mixture region, moreover, the cellular structures become finer, with increasing the mixture strength.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.75-84
• /
• 1988

The performance and emission for the 4-cylinder 4-cycle gasoline engine fueled with methanol is predicted in this paper. The model for all the processes is illustrated. It computes the gas pressure, gas temperature and the rate of formation of nitric oxide and carbon monoxide at each crank angle using basic energy equation and reaction kinetic mechanism. The results are obtained at different operating conditions encompassing changes in fuel-air equivalence ratio, engine speed, spark timing and compression ratio. The special characteristics of methanol such as high power output and nitric oxide emissions have been truthfully predicted by the model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.17-22
• /
• 2000

The transient process simplified by the 1-D stretched laminar flame formed at the fuel-oxidizer interface was investigated using the coherent flame sheet model. Under the combustion environment of high temperatures and pressures the results show that the time required to reach the steady state was relatively short compared to the reverse of strain rate. Hence the employment of the tabulation of precalculated steady-flame results in the calculation of turbulent diffusion flames using the coherent flame sheet model is concluded valid, Also upstream temperatures were found to have only a minor effect on the nondimensional flame temperature and nondimensional fuel even through the letter is sensitive to pressure changes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.30-40
• /
• 1995

Optically accessible D. I. diesel engine with a rectangular combustion chamber was constructed to visualize the behaviors of sprays and flames in the combustion camber with the close conditions of pressure and temperature in an actual engine. The behaviors of sprays and flames in the combustion chamber as the operating conditions of this engine were photographed with high speed camera by Diffused Background Illumination Method. With photographs taken by this method, behavior of spray droplets injected into the combustion chamber, ignition points, and flame propagation were observed and analyzed at a time-and space-dependent fashion.

• Journal of Surface Science and Engineering
• /
• v.25 no.1
• /
• pp.8-15
• /
• 1992

To investigate the effects of substrate on transverse-rupture strength(TRS) and bonding strength between substrate and TiC layer coated by CVD, two kinds of substrate (substrate A: WC-9.5wt% Co-MC＊[low C], substrate B: WC -6wt% Co-MC＊[high C]) were studied in terms of Cobalt and C contents respectively. For preparation of test samples the coating parameters of deposition time, deposition temperature and deposition pressure were varied. The results show that the carbon contents in substrates have greater effects on the TRS of the CVD TiC coated cemented carbide than Co contents in substrates. ＊MC:TiC+TaC

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.228-231
• /
• 2003

Experimental investigations of AC breakdown characteristics of liquid nitrogen in the environment to restrain boil bubbles are presented in this paper. The environment to restrain vapor bubble in the liquid nitrogen is both increasing pressure and decreasing temperature. Measurements of the breakdown voltage of liquid nitrogen in the environment to restrain vapor bubbles are investigated under AC high voltage in a quasi-uniform and non-uniform electrical field for pressures and temperatures ranging from 0 to 0.5 MPa and 77 K to 65 K respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.399-402
• /
• 2005

We have studied the Pixel Isolated Phase Separated Composite Organic Film (PI-PSCOF). The PI-PSCOF can be made by the anisotropic phase separation between Ferroelectric Liquid Crystals and Pre-polymer materials by irradiating the UV with optimizing its intensity and time. In the technology, the FLC molecules are isolated in pixels where FLCs are surrounded by the inter-pixel vertical polymer walls and the horizontal polymer films on the upper substrate. The good merits of this technology are fast response time, and good mechanical and thermal stability against external high pressure and temperature. We will compare the results obtained from FLC, PSCOF, and PI-PSCOF modes by using the electro-optic measurement and x-ray scattering, and mechanical method. We believe that the PI-PSCOF technology can be a best candidate for future Flexible Display Applications.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2252-2254
• /
• 2002

The Reactor internal structures which consist of many complex components are subjected to flow-induced vibration due to high temperature and pressure in Reactor coolant system. The above flow-induced vibration causes degradation of structural integrity of the Reactor and may result in loosing mechanical binding component which might impact other equipment and component or cause flow blockage. It is important to analyze reactor noise signal for the early detection of potential problem or failure in order to diagnosis reactor integrity in the point of view of safety and plant economics. Detailed composition of diagnostic system reactor internal structures using neutron noise(RIDS).

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.509-510
• /
• 2000

Piezoelectric ZnO thin films were deposited on slide glass by Facing Targets Sputtering(FTS). The Facing Targets Sputtering system can deposit thin film in plasma-free situation and change the deposition condition in wide range. The characteristics of zinc oxide thin films on power, working pressure, and substrate temperature were investigated by XRD (x-ray diffractometer), alpha-step (Tencor) and SEM (Scanning Electron Microscopy) analyses. In the results, we suggest that FTS system is very suitable to preparing high quality ZnO thin films with good c-axis orientation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.110-113
• /
• 2005

Ozone is useful oxidizing gas for the fabrication of BSCCO thin films. In order to obtain high quality oxide BSCCO thin films, higher ozone concentration is necessary. The growth rates of the films was set in the region from 0.17 to 0.27 nm/min. MgO(100) was used as a substrate. In this paper oxidation property was evaluated relation between oxide gas pressure and inverse temperature(CuO reaction). The obtained condition was formulated by the fabrication of Cu metal thin film by co-deposition using the Ion Beam Sputtering method. Because the CuO phase peak appeared at the XRD evaluation of the CuO thin film using ozone gas, this study has succeeded in the fabrication of the CuO phase at $825^{\circ}C$.