• 소성∙가공
• /
• 제5권4호
• /
• pp.327-336
• /
• 1996

The effect of dynamic strain aging on high temperature deformation behaviour of the A-Mg alloy was investigated by strain rate change tests and stress relaxation tests between 20$0^{\circ}C$and 50$0^{\circ}C$. Yield point, short stress transient and periodic discontinuities on the stress-strain curve were considered as an evidence of the effect of dynamic strain aging. With this criterion two distinct strain rate-temperature regimes could be manifested. Dynamic strain aging was considered to be effective in the high temperature-low strain rate regime, whereas dynamic recovery was a dominant deformation mechanism in the low temperature-high strain rate regime. It was found that dynamic strain aging in the high temperature deformation was governed by the mechcanism of diffusion-controlled, viscous dislocation movement.

• Journal of Welding and Joining
• /
• 제26권5호
• /
• pp.60-65
• /
• 2008

Ferritic stainless steels of the 400 series have been available for automotive exhaust system, heat exchanger, radiater etc. in various industrial because heat resistance, corrosion resistance and strength are excellent. Especially, automotive exhaust system is required good heat resistance because typical temperature of exhaust system exposed during operation of engine is reach up to $800^{\circ}C$. However, research for effect of high temperature in ferritic stainless steels is not enough. In this study, high temperature tensile properties of lap weld of ferritic stainless steels(STS 429) were investigated. In accordance with heat input, lap welds had been produced and were evaluated at high temperature($800^{\circ}C$) to compare high temperature tensile properties. In addition, room temperature tensile tests were carried out for non-aging and aging specimens. As a result of R.T tensile test, non-aging specimens were fractured in base metal except for low heat input specimen and aging specimens were fractured in weld metal. Also high temperature tensile test were carried out by aging specimen. After high temperature tensile test, fracture of aged specimen was occurred in base metal except for low heat input specimen. Fracture surface of low heat input specimen in weld metal was confirmed as brittle fracture with observation using scanning electron microscope(SEM). Significant decrease in ultimate tensile strength (between 82 and 85%) was observed for aged ferritic stainless steels(STS 429) when tested at high temperature.

• 한국식품과학회지
• /
• 제21권4호
• /
• pp.549-555
• /
• 1989

저급육인 한우숫소의 앞다리고기를 도살직후 $16{\pm}2^{\circ}C$에서 고온숙성하여 연도개선 효과를 검토하였다. 또한 24시간 고온숙성한 후, 재구성육을 조제하여 결착성 개선방법을 모색하였다. 시료의 처리는 소금(0, 0.5, 1.0%), pyrophosphate(0, 0.3, 0.5%)와 이들의 혼용효과를 검토하였고, 소금(0.5%)과 pyrophosphate(0.3%)를 혼용한 원료에 succinic anhydride(0, 0.1, 0.2, 0.3%)를 첨가하여 석시닐산의 첨가효과를 검토하였다. 얻어진 결과는 다음과 같다. 1. 고온숙성은 저온숙성에 비하여 전단력이 낮았고, 근원섬유소편화지수가 높았으며, 연도개선의 효과가 뛰어났다. 전자현미경에 의한 형태학적 변화의 결과도 이들 결과 일치하였다. 2. 재구성육의 파단응력은 소금과 인산염의 첨가수준이 증가할수록 높아졌고, 소금과 인산염을 혼용할 경우, 현저히 증가하였다. 3. 조리수율은 소금과 인산염의 첨가수준이 증가할수록 낮아졌고, 소금과 인산염을 혼용할 경우, 현저하게 감소하였다. 4. TBA가는 소금 첨가수준에 비례하여 증가하였으며, 인산염 및 인산염과 소금혼용의 경우는 약간 증가하는 경향이었다. 5. 석신산은 재구성육의 결착력과 품질개선에 전혀 도움이 되지 않았다.

• International Journal of Automotive Technology
• /
• 제1권2호
• /
• pp.71-77
• /
• 2000

High temperature materials in service are subjected to mechanical damage due to operating load and metallurgical damage due to operating temperature. Therefore, when designing or assessing life of high temperature components, both factors must be considered. In this paper, the effect of tensile hold time on high temperature fatigue crack growth and long term prior thermal aging heat treatment on creep rupture behavior were investigated using STS 316L and STS 316 austenitic stainless steels, which are widely used for high temperature components like in automotive exhaust and piping systems. In high temperature fatigue crack growth tests using STS 316L, as tensile hold time increased, crack growth rate decreased in relatively short tensile hold time region. In long term aged specimens, cavity type microcracks have been observed at the interface of grain boundary and coarsened carbide.

• 열처리공학회지
• /
• 제6권4호
• /
• pp.213-222
• /
• 1993

This research was performed to investigate the transformation behavior and shape memory effect of Cu-13.5Al-4.5Ni(wt%) alloy with various aging temperature and time. The results obtained in this study are as follows: Transformation temperature was very increased when aging temperature is at $250^{\circ}C$. The variation of transformation temperature in first reverse transformation cycle and second was very significant, but there was little difference in case of 2nd and 3rd. Transformation temperature at various aging temperature was increased with increasing of aging temperature and time. Microvickers hardness was increased with increasing of aging temperature and time. It was found that ${\alpha}$ and ${\gamma}_2$ phase were created by aging of long time at high temperature.

• 한국재료학회지
• /
• 제18권5호
• /
• pp.266-271
• /
• 2008

Magnesium alloys are alloyed with rare earth elements (Re, Ca, Sr) due to the limited use of magnesium in high-temperature conditions. In this study, the influences of Zr and Zn on the aging behavior of a Mg-Nd-Y alloy were investigated. magnesium alloys containing R.E elements require aging treatments Specifically, Nd, Y and Zr are commonly used for high-temperature magnesium alloys. Various aging treatments were conducted at temperatures of 200, 250 and $300^{\circ}C$ for 0.5, 1, 3, 6, and 10 hours in order to examine the microstructural changes and mechanical properties at a high temperature ($150^{\circ}C$). Hardness and high-temperature ($150^{\circ}C$) tensile tests were carried out under various aging conditions in order to investigate the effects of an aging treatment on the mechanical properties of a Mg-3.05Nd-2.06Y-1.13Zr-0.34Zn alloy. The maximum hardness was 67Hv; this was achieved after aging at $250^{\circ}C$ for 3 hours. The maximum tensile, yield strength and elongation at $150^{\circ}C$ were 237MPa, 145MPa and 13.6%, respectively, at $250^{\circ}C$ for 3 hours. The strengths of the Mg-3.05Nd-2.06Y-1.13Zr-0.34Zn alloy increased as the aging time increased to 3 hours at $250^{\circ}C$ This is attributed to the precipitation of a Nd-rich phase, a Zr-rich phase and $Mg_3Y_2Zn_3$.

• 한국축산식품학회지
• /
• 제36권2호
• /
• pp.215-222
• /
• 2016

The combined effects of irradiation and aging temperature on the microbial and chemical quality of beef loin were investigated. The samples were vacuum-packaged, irradiated at 0 or 2 kGy using electron-beam (EB), and stored for 10 d at different aging temperatures (2, 14, or 25℃). The microbial growth, shear values, meat color, and nucleotide-related flavor compounds of the samples were analyzed. The irradiation effect on inactivation of foodborne pathogens was also investigated. The population of Listeria monocytogenes and Escherhia coli O157:H7 inoculated in beef samples decreased in proportion to the irradiation dose. Irradiation reduced the total aerobic bacteria (TAB) over the storage, but higher aging temperature increased the TBA. Thus TAB increased sharply in non-irradiated and high temperature-aged (14, 25℃) beef samples after 5 d. With increasing aging temperature and aging time, shear force values decreased. Lipid oxidation could be reduced by short aging time at low aging temperature. The color a* values of the irradiated beef were lower than those of the non-irradiated throughout the aging period. As aging period and temperature increased, IMP decreased and hypoxanthine increased. Considering microbial and physicochemical properties, irradiation can be used for raw beef to be aged at relatively high temperature to shorten aging time and cost.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제12권3호
• /
• pp.177-186
• /
• 2012

This paper presents a comparison of the failure mechanism for high power converted white LEDs(3W) with the commercially available YAG:Ce and silicate phosphor. We carry out the normal aging life test for 10,000 hours, the high temperature aging test for 8,000 hours, the high temperature and humidity aging test for 8,000 hours and the current aging testing for 5,000 hours. The optical and electrical parameters of LEDs were monitored, such as lumen, correlated color temperature (CCT), chromaticity coordinates(x, y), thermal resistance, I -V curve and spectrum intensity. The stress induced a luminous flux decay on LED in all experiments and causes a failure. So we try to find out what's a main failure mechanism for a high power LED.

• 수산해양기술연구
• /
• 제20권1호
• /
• pp.23-29
• /
• 1984

고역알루미늄합금의 파괴특성에 미치는 시효열처리의 영향에 대하여 검토한 결과는 다음과 같다. 1. 현미경 조직의 관찰결과 $190^{\circ}C,$ 12hr로 시효열처리한 것이 시효강화된 양호한 조직과 미세한 석출분포를 나타내고 있음을 알 수 있었다. 2. 계단식시효열처리에 의하여 정상시효열처리보다 시효시간을 반정도로 단축시킬 수 있었고, 이들 조직도 유사하였다. 3. 인장파단면의 SEM 전자현미경 사진관찰결과는 $190^{\circ}C,$ 12hr으로 시효열처리한 것은 딤플형 입계 및 입내연성파괴를 나타내나, 이를 제외한 대부분은 시효열처리 시간과 온도에는 관계없이 입계연성파괴인 것이 관찰되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1391-1393
• /
• 2008

In this paper, the long-term reliability for 1.25G transceiver in use of high speed optical access network is investigated. High temperature storage tests and accelerated life tests are used to long-term reliability. Accelerated aging test have been during 3,000 hour of the three accelerated aging conditions by caused high temperature stress. Mean life is assumed to follow the Arrhenius relationship and analysis from the failure data obtained in the accelerated aging conditions.