• Earthquakes and Structures
• /
• 제12권2호
• /
• pp.201-211
• /
• 2017

This paper experimentally investigates the effect of yield strength of reinforcing bars and stirrups on the seismic performance of reinforced concrete (RC) circular piers. Reversed cyclic loading tests of nine-large scale specimens with longitudinal and transverse reinforcement of different yield strengths (varying between HRB335, HRB500E and HRB600 rebars) were conducted. The test parameters include the yield strength and amount of longitudinal and transverse reinforcement. The results indicate that the adoption of high-strength steel (HSS) reinforcement HRB500E and HRB600 (to replace HRB335) as longitudinal bars without reducing the steel area (i.e., equal volume replacement) is found to increase the moment resistance (as expected) and the total deformation capacity while reducing the residual displacement, ductility and energy dissipation capacity to some extent. Higher strength stirrups enhance the ductility and energy dissipation capacity of RC bridge piers. While the product of steel yield strength and reinforcement ratio ($f_y{\rho}_s$) is kept constant (i.e., equal strength replacement), the piers with higher yield strength longitudinal bars are found to achieve as good seismic performance as when lower strength bars are used. When higher yield strength transverse reinforcement is to be used to maintain equal strength, reducing bar diameter is found to be a better approach than increasing the tie spacing.

• 콘크리트학회논문집
• /
• 제13권3호
• /
• pp.244-250
• /
• 2001

지진하중이 작용할 때, 철근콘크리트 구조물에서 취성파괴의 원인은 철근과 콘크리트사이의 과도한 부착손실에 기인한다. 본 연구에서는 반복하중 작용시에 철근의 마디형태에 따른 부착성능의 영향을 평가하고자 하였다. 철근의 마디높이에 변화를 주어 상대마디면적에 변화를 주었고, 횡구속철근양에 변화를 주었다. 단조가력시 횡구속이 증가할수록 부착력도 증가하며 상대마디면적의 증가에 따라서도 약간의 강도변화가 발생하였다. 단조가력시에 비해서 반복가력시에 상대마디면적이 증가할수록 부착력 증가가 더욱 커지는 것으로 관찰되었다. 반복가력시 상대마디면적의 증가에 따른 부착강도의 증가가 횡구속 철근이 있을 때 더욱 뚜렷하게 나타났다. 반복가력시 일정한 슬립에서 반복횟수가 증가할수록 강성은 떨어졌으나, 상대마디면적 증가에 따라 부착슬립량의 감소도 크게 발생했다. 따라서 지진과 같은 반복가력시 상대마디면적이 큰 철근을 사용함으로서 더 작은 슬립으로 더 큰 부착강도를 발휘하게 되어 구조물의 내진성능을 개선시킬 수 있겠다.

• 토지주택연구
• /
• 제8권4호
• /
• pp.257-266
• /
• 2017

LH has been using ultra high strength reinforcing bars (SD500 and SD600), since 2011. Such a change requires an adjustment of the old extra rates of bar splice to reflect use of ultra high strength reinforcing bars, as these rates had been set based on SD400 bars. It is particularly difficult to calculate precisely rebar lap-splice locations for large areas, such as those in apartment buildings. This research aims to adjust the extra rates of bar splice to reflect a reasonable rate; the rebar lap-splice length is not an exact estimation, but instead, an extra rates of bar splice is set and the rebar lap-splice length is increased by 2% (D 10) - 7% (025) depending on the bar size. The subjects of this study are LH apartments undergoing frame construction. We studied the quantity estimations from the design drawings, and analyzed the settlement quantities of construction field. The results of the study revealed that, when each of the quantities are analyzed, consider adjusting the extra rates of bar splice of some rebar to 1% - 3.5%. This was caused by an overuse of reinforcing bars in onsite construction and the use of supporting bars that have not been reflected in the documents, among other reasons. Based on the results of our study, an improvement plan for the current extra rates of bar splice seems to be necessary, cutting or raising the rate depending on the analysis of the data. Through this study, we expect to contribute to the calculation of reasonable construction costs, improvements in the quality of rebar work, and improvements in the capacity of design techniques for apartment buildings.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.489-492
• /
• 2006

Needs for the new technologies and cutting-edge Ultra Flowing Self-Compacting Concrete are emerging as the concrete structures are becoming bigger and more specialized recently. In North America and Europe, SCC, which has high resistance against flow ability and segregation, is being used as concrete material in applications such as precast and prestressed bridges, where reinforcing bars are overcrowdedly placed. In Korea, SCC has been utilized limitedly in building structures but its utilization should be expanded to engineering structures such as bridges. In this study, for the application in precast and prestressed bridges with overlycrowded reinforcing bars, USCC was mixed with admixtures to give a binary system and a ternary system according to the 1st grade rules by JSCE (Japan Society of Civil Engineers). Compressive strength and splitting tensile strength of the resulting USCCs were tested. Elastic modulus were compared with the values suggested in CEB-FIP code and ACI 318-05.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.13-16
• /
• 2008

전단경간-깊이의 비가 1을 넘지 않는 캔틸레버로서 응력교란구역을 형성하는 내민받침은 보에 의해 전달되는 수직하중과 지지하고 있는 부재의 수축, 온도 변형, 크리프 변형에 의해 전달되는 수평 하중에 저항하는 부재이다. 최근, 고강도 콘크리트의 사용이 증가하고 있고, 철근 콘크리트 구조물의 부식에 대한 관심이 높아지면서 고성능의 보강재를 콘크리트 부재에 전략적으로 적용하는 하이브리드 보강기법에 대한 연구가 활발히 진행되고 있다. 이에 본 연구에서는 강섬유 및 헤디드 바를 활용한 하이브리드 보강 기법을 내민받침에 적용하고자 섬유보강 고강도 콘크리트 내민받침을 제작하고 구조실험을 실시하였다. 강섬유의 혼입, 강섬유 혼입률의 증가에 따라 고강도 콘크리트 내민받침의 내하력, 강성, 연성은 증가하는 것으로 나타났고, 최대 균열폭은 감소하였다. 또한, 횡방향 철근에 용접하여 주인장 타이 철근을 정착한 내민받침 보다 헤디드 바를 주인장 타이 철근으로 사용한 내민받침이 더 높은 내하력, 강성, 연성을 보였다.

• 한국공간구조학회논문집
• /
• 제5권2호
• /
• pp.89-97
• /
• 2005

건축 구조물이 초고층화, 대형화, 특수화 되어감에 따라 고강도 재료의 사용이 증대되고 있으며, 고강도 재료가 사용된 철근콘크리트 보의 전단강도를 타당하게 예측할 수 있는 해석모델이 반드시 필요하다. 본 연구에서는 고강도 철근이 사용된 철근콘크리트 보의 전단강도를 타당하게 예측할 수 있는 트러스 모델을 제안한다. 고강도 철근이 사용된 철근콘크리트 보의 전단강도에 대한 제안된 모델인 TATM의 타당성을 검토하기 위하여 총 107개 보의 실험결과를 수집하였으며, TATM 및 기존 트러스 모델의 전단강도 해석결과를 이들 실험결과와 비교하였다. 비교 결과, TATM은 다른 트러스 모델보다 실험결과를 더 잘 예측하였으며, TATM의 해석결과에 대한 실험결과의 비는 인장철근과 전단 철근의 항복강도에 거의 관계없이 일정하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.270-273
• /
• 2006

Bond between reinforcing bar and the surrounding concrete is made up of three components. There are chemical adesion, friction, and mechanical interaction between the rib of the bar and the surrounding concrete. bond of deformed bars depends primarily on the beraing of rib deformation anainst the surrounding concrete. The final objective of the study is to enhance structural stability, and workability thorough increasing the bond strength between deformed bar and surrounding concrete. The results of this study will be used to shorten bond and development length by $20{\sim}30$ percent and it will facilitate to use of high strength and high-relative rib area bars.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.545-550
• /
• 2000

Bond between reinforcing bars and the surrounding concrete is supposed to safely transfer load in the design process of reinforced concrete structures. Bar with high relative rib area will be studied further not only static load but also dynamic loading conditions to sustain better performance of bond for reinforced concrete structures under earthquake. To determine the bond behavior of high ribbed bars in beam and column joints under repeated loads, 31 pullout specimens were tested. Bond strength increases as relative rib area increases. Also the effect of relative rib area on bond is larger in cyclic loading than in monotonic loading.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.319-324
• /
• 1994

Bond test was carried out to assess the effect of several variables on bond characteristics between reinforcing bar and concrete. Key variables are concrete compressive strength(low, medium high, and ultra-high), bar diameter(13mm and 22mm), and concrete cover(25mm; 1-inch, 38mm; 1.5-inch, and 51mm; 2-inch). Confining effect and bar spacing are not taken into account. Thirty-two specimens subjected to uniaxial tension were tested under hypothesis uniform bond stress distribution along the reinforcing bar embeded in concrete. Test results(ultimate bond stress) were compared with bond and development provisions of the ACI building Code(ACl 318-89) and local bond stress versus slip relationship diagram represented to show effect of the above variables.

• 한국농공학회지
• /
• 제39권6호
• /
• pp.122-130
• /
• 1997

An experimental study was conducted to evaluate the bond performance of reinforcing bars embedded in high-strength concrete. Four bond specimens and ten beam splice specimens using concrete with compressive strength of 246kgf/$cm^2$ and 64lkgf/$cm^2$ were tested. The effect of several variables on basic development length and compressive strength of concrete is discussed in splice specimens. The test results showed that the current trend in concrete specification of making the splice length longer to compensate for having smaller cover and spacing may not be an effective approach.