• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.205-209
• /
• 2014

Medical polymers require sterilization and must be able to maintain material properties for a specified shelf life. Sterilization can be achieved by using gamma or e-beam exposure. In this study, accelerated aging tests of poly(ether-block-amide) (PEBA) copolymer samples is presented. PEBA copolymer samples with different polyether content that result in Shore hardness of 35D to 72D, were sterilized using e-beam radiation followed by accelerated aging at $55^{\circ}C$. E-beam sterilization effect on molecular weight and mechanical property has performed and analyzed. The average molecular weight significantly reduced as a result of ageing. The enlarged proportion of low molecular weight chains in the aged samples is consistent with the generation of degradation products produced by oxidative chain scission. Also E-beam materials have shown decreased tensile strength and elongation. Overall, this study demonstrated that the medical grade PEBA was significantly affected by radiation exposure over aging time, particularly at high irradiation doses. For medical use in case of radiation sterilization required, it is recommended to avoid Pebax material. If Pebax material must be in use for medical device, recommend to use alternate sterilization method such as Ethylene Oxide sterilization.

• Clean Technology
• /
• v.22 no.4
• /
• pp.258-268
• /
• 2016

In this work, carboxymethylcellulose-based composite superabsorbent hydrogels were prepared by electron beam radiation. The composition of carboxymethylcellulose (CMC) varied from 4 wt%, 5 wt%, and 6 wt% to 7 wt% based on the amount of distilled water in the syntheses of hydrogels. Graphite oxide, reduced graphene oxide, activated carbon, and bentonite were used as additives for the synthesis of composite superabsorbent. The effect of CMC composition and the type of additives on the gel properties of the prepared hydrogels was investigated. In order to verify the functional groups in the prepared materials, Fourier transform infrared spectroscopy was used. In addition, mechanical strength, gel fraction, swelling kinetics, and equilibrium swelling ratios were measured for the prepared hydrogels. Swelling experiments were carried out in distilled water, urea solution, and physiological saline water. Prepared hydrogels were reused for 5 times, and gel fraction and swelling ratio were measured at every 24 hours. Among the prepared hydrogels, $C_{5%}GO$ and $C_{5%}rGO$ exhibited excellent mechanical property and relatively high swelling ratios for urea solution and physiological saline water with promising applicability as slow-release fertilizers.

• Journal of Periodontal and Implant Science
• /
• v.42 no.2
• /
• pp.59-63
• /
• 2012

Purpose: This study evaluated the surface characteristics and bond strength produced using a novel technique for coating hydroxyapatite (HA) onto titanium implants. Methods: HA was coated on the titanium implant surface using a super-high-speed (SHS) blasting method with highly purified HA. The coating was performed at a low temperature, unlike conventional HA coating methods. Coating thickness was measured. The novel HA-coated disc was fabricated. X-ray diffraction analysis was performed directly on the disc to evaluate crystallinity. Four novel HA-coated discs and four resorbable blast medium (RBM) discs were prepared. Their surface roughnesses and areas were measured. Five puretitanium, RBM-treated, and novel HA-coated discs were prepared. Contact angle was measured. Two-way analysis of variance and the post-hoc Scheffe's test were used to analyze differences between the groups, with those with a probability of P<0.05 considered to be statistically significant. To evaluate exfoliation of the coating layer, 7 sites on the mandibles from 7 mongrel dogs were used. Other sites were used for another research project. In total, seven novel HA-coated implants were placed 2 months after extraction of premolars according to the manufacturer's instructions. The dogs were sacrificed 8 weeks after implant surgery. Implants were removed using a ratchet driver. The surface of the retrieved implants was evaluated microscopically. Results: A uniform HA coating layer was formed on the titanium implants with no deformation of the RBM titanium surface microtexture when an SHS blasting method was used. Conclusions: These HA-coated implants exhibited increased roughness, crystallinity, and wettability when compared with RBM implants.

• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.42-48
• /
• 2014

Soot and tar which were derived from combustion or pyrolysis processes in Puverized Coal(PC) furnace or boiler have been significantly dealing in a radiative heat transfer and an additional source of NOx. Furthermore, the increasing for the use of a coal with low caloric value gives rise to a lot of tar-soot yield and LOI in a recycled ash for using cement materials. So, the ash with higher tar-soot yield and LOI can not recycle due to decreased strength of concrete. In this study, tar-soot yields and flame structures were investigated using the LFR for a blending combustion with bituminous coal and sub-bituminous coal. Also, The investigation were conducted as each single coals and blending ratio. The coals are used in a doestic power plant. In the experimental results, sub-bituminous coal with high volatile contents shows longer soot cloud length than bituminous coal, but overall flame length was shorter than bituminous coal. Tar-soot yields of sub-bituminous coal is lower than those of bituminous coal. Combustion characteristics are different between single coal and blended coal. Therefore, finding an optimal coal blending ratio according to coal rank effects on tar-soot yields.

• Resources Recycling
• /
• v.13 no.2
• /
• pp.39-46
• /
• 2004

The amount of electric furnace dust has been steadily increasing due to the increase of iron scraps which are usually recycled by electric furnace melting process. To date, this electric furnace dust has usually been treated by landfilling, however, because of shortage of landfill sites and heavy metal leaching more desirable treatment schemes are urgently needed. Among several possible schemes for the proper treatment of electric furnace dust, its recycling can be said to be most desirable. In present study, the triboelectrostatic separation of zinc and zinc-containing components from electric furnace dust was attempted based on its physicochemical properties such as particle shape, size distribution, and chemical assay. The dust was found to be mixed with spherical and non-spherical shaped particles and its major component materials were $ZnFe_2$$O_4$, ZnO, Fe, Zn, and FeO. The content of zinc-containing components in the entire dust was observed to be in the range of 15～30 wt%, which reasonably justified that zinc is recyclable. The triboelectrostatic characteristic of each component material was found to be different each other since their work functions were different, and based on this characteristic zinc and zinc-containing component could be flirty separated from the dust. After selecting a proper tribo-elec-trification material, the separation features of zinc and zinc-containing component were examined by taking the distance of electrodes, electric field strength, and scavenging as the experimental variables. The highest zinc-content obtained under the optimal separating condition was found to be up to 50wt%.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.1 s.119
• /
• pp.38-47
• /
• 2007

This study was carried out to develop a new application field and obtain the basic data of citrus peel as waste in Jeju island and traditional Hanji for producing functional Hanji. The results measuring physical and optical properties, water vapor permeance and antibacterial activity are as follows. It was revealed that apparent density go as down but bulk raise up in the structural view of Hanji with increasing of the addition various Korean citrus peel (citrus unshiu, cheonggyun and hanrabong peel, and citrus unshiu peel powder) percentages, and that the density of Hanji added citrus unshiu peel was higher, but bulk was lower in compared with Hanji added other kinds of peel. Those Hanji added citrus unshiu peel, cheonggyun peel, hanrabong peel and citrus unshiu powder were very great not only in the strength (breaking length, burst index, tear index and folding endurance) but also in water vapor permeant rate in comparison with Hanji. The pHs of Hanji were neutrality (7 to 8). The brightness of the Hanji added various citrus peel percentages was low in compared to Hanji, and the 40% addition of hanrabong peel was the lowest. When 40% hanrabong peel was added to Hanji, it was very yellow in the color degree. When cheonggyun peel was added to Hanji manufacture, water vapor permeant rate was highly effective. It is known that vacant space of intrafiber was reduced by image analysis of Hanji and the additions of peel of citrus unshiu, cheonggyun and hanrabong were distributed equally in the interior of Hanji. The antibacterial activity of Hanji added citrus unshiu peel is more than 98%. After all, it would be able to increase utilization of Hanji, extensively. Namely, production of high quality Hanji added functional materials is expected for new valuable industry of citrus peel and Hanji.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.17-21
• /
• 2019

In this study, selective laser sintered 3D printing mold core and metal core were used to investigate the difference of the thickness shrinkage from the gate of the injection molded part at a constant interval. SLS 3D printing mold core was made of nylon-based PA2200 powder and the metal core was manufactured by conventional machining method. As the PA2200 powder material has low strength, thermal conductivity and high specific heat characteristics compared with metal, molding conditions were set with the consideration of molten temperature and injection pressure. Crystalline resin(PP) and amorphous resin(PS) with low melting temperature and viscosity were selected for the injection molding experiment. Cooling time for processing condition was selected by checking the temperature change of the cores with a cavity temperature sensor. The cooling time of the 3D printing core was required a longer time than that of the metal core. The thickness shrinkage of the molded part compared to the core depth was measured from the gate by a constant interval. It was shown that the thickness shrinkage of the 3D printing core was 2.02 ~ 4.34% larger than that of metal core. In additions, in the case of metal core, thickness shrinkage was increased with distance from the gate, on the contrary, in the case of polymer core showed reversed aspect.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.2
• /
• pp.206-219
• /
• 2013

This study aims to estimate firing temperature and physicochemical properties of the four clay bricks excavated from the Maritime Province of Siberia. Analysis result shows that the specimens are composed of clay, quartz and feldspar, and some specimens include carbonized organic materials which were probably added in order to enhance its physical strength in bricks. Major mineral components of the bricks are quartz, illite and clay minerals. The result identifying the existence of silimanite by XRD suggests that white material of the Koc 1 was painted for a certain purpose. Unlike most specimens which contained hematite, several samples contain Mullite. Such result suggests that some bricks were fired at high temperature. Furthermore, the results from TG analysis which does not display exothermic peak which appears at between $800^{\circ}C$ to $1,000^{\circ}C$ but display endothermic peak at $900^{\circ}C$ and it also confirms that they were exposed at $900^{\circ}C$ or higher.

• Structural Engineering and Mechanics
• /
• v.70 no.1
• /
• pp.67-80
• /
• 2019

Strengthening with near surface mounted carbon fibre reinforced polymers (NSM-CFRP) is a strengthening technique that have been used for several decades to increase the load carrying capacity of reinforced concrete members. In Iraq, many concrete buildings and bridges were subjected to a wide range of damage as a result of the last war and many other events. Accordingly, there is a progressive increase in the strengthening of concrete structures, bridges in particular, by using CFRP strengthening techniques. Near-surface mounted carbon fibre polymer has been recently proved as a powerful strengthening technique in which the CFRP strips are sufficiently protected against external environmental conditions especially the high-temperature rates in Iraq. However, this technique has not been examined yet under repeated loading conditions such as traffic loads on bridge girders. The main objective of this research was to investigate the effectiveness of NSM-CFRP strips in reinforced concrete beams under repeated loads. Different parameters such as the number of strips, groove size, and two types of bonding materials (epoxy resin and cement-based adhesive) were considered. Fifteen NSM-CFRP strengthened beams were tested under concentrated monotonic and repeated loadings. Three beams were non-strengthened as reference specimens while the remaining were strengthened with NSM-CFRP strips and divided into three groups. Each group comprises two beams tested under monotonic loads and used as control for those tested under repeated loads in the same group. The experimental results are discussed in terms of load-deflection behavior up to failure, ductility factor, cumulative energy absorption, number of cycles to failure, and the mode of failure. The test results proved that strengthening with NSM-CFRP strips increased both the flexural strength and stiffness of the tested beams. An increase in load carrying capacity was obtained in a range of (1.47 to 4.49) times that for the non-strengthened specimens. Also, the increase in total area of CFRPs showed a slight increase in flexural capacity of (1.02) times the value of the control strengthened one tested under repeated loading. Increasing the total area of CFRP strips resulted in a reduction in ductility factor reached to (0.71) while the cumulative energy absorption increased by (1.22) times the values of the strengthened reference specimens tested under repeated loading. Moreover, the replacement of epoxy resin with cement-based adhesive as a bonding material exhibited higher ductility than specimen with epoxy resin tested under monotonic and repeated loading.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.65-70
• /
• 2021

In this study, interfacial properties and mechanical properties of joints were reported after Cu pads finished with organic solderability preservative (OSP) on flame retardant-4 (FR-4) printed circuit board (PCB) and electronic components were joined with a Sn-57Bi-1Ag solder paste by using a laser bonding process. The laser bonding process was performed under various bonding conditions with changing a laser power and a bonding time and effects of bonding conditions on interfacial and mechanical properties of joints were analyzed. In order to apply for industry, properties of bonding joints using a reflow bonding process which are widely used were compared. When the laser bonding process were performed, we observed that Cu₆Sn₅ intermetallic compounds (IMCs) were fully formed at the interface although the bonding times were very short about 2 and 3 s. Furthermore, void formations of the joints by using the laser bonding process were suppressed at the joints with comparing to the reflow bonding process and shear strengths of bonding joints were higher than that by using the reflow bonding process. Therefore, in spite of a very short bonding time, it is expected that joints will be stably formed and have a high mechanical strength by using the laser bonding process.