• 소성∙가공
• /
• 제27권3호
• /
• pp.145-153
• /
• 2018

Magnesium material could be widely used in the automotive industry because of its high strength to weight ratio, but the electric resistance spot welding process of magnesium sheets is difficult because of its low electric resistance and high thermal conduction and thermal expansion. For this reason, an electric resistance surface friction spot welding process using rotating dies is suggested for the spot welding of magnesium metal sheets. This welding method can be characterized by three heating methods: (1) electric resistance heating on contacted surface, (2) surface friction heating by rotating dies, and (3) thermal conduction heating from heated steel electrodes, for the fusion of metal at the interfacial zone between the two magnesium sheets. This welding process also has variables to explore, such as welding currents, diameters of the steel electrode, and rotating dies. It was found that the welding strength could reach industrial requirements by applying a welding current of 11.0kA, with steel electrodes of 12mm diameter, with rotating dies of 4.4 mm diameter, under the condition of a revolution speed of 1200rpm of rotating dies, for the surface friction spot welding process of AZ31 magnesium alloy sheets of 1.4mm thickness.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.439-443
• /
• 2008

We investigate the mechanical behavior of a pre-heat treated steel of ESW95, which is being used for automotive parts including tie-rods to save manufacturing cost and enhance product quality. SCM435 is also investigated to reveal the characteristics of the pre-heat treated steel tested. AFDEX/MAT is used to extract the true stress-strain curve over the large strain with higher accuracy. It has been found that ESW95 has very week strain-hardening behavior which can be negligible compared with SCM435 and that the initial yield strength is quite high and the toughness of ESW95 reaches nearly 75% of SCM435. ESW95 is characterized by the weak strain-hardening behavior and high yield strength that can be lead to minimization of post-processing including heat treatment and straightening. ESW95 and SCM435 are also compared by applying them to ball-stud forging by computer simulation. It is expected that a great deal of change may take place in production as well as in service if the pre-heated steels are adopted.

• 오토저널
• /
• 제14권6호
• /
• pp.105-112
• /
• 1992

The turning tests with sintered carbide tools have been conducted on typical high strength SSW2 railway wheel steel and its machinability were examined in terms of the cutting resistance, the roughness of turning surface, the chip disposal and others. Some results obtained in this paper are as follows: (1) The cutting resistance is not affected by the cutting speed (in this paper these were 23-78 m/min). (2) The roughness of finished surface is found to be largely dependent on cutting conditions and tool geometry. (3) There exists the explicit relates between the tool geometry cutting conditions (cutting speed, feedrate, and depth of cut) and independent variables(cutting resistance, surface roughness) are derived.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.83-90
• /
• 2004

In this study, CT specimens were prepared from spring steel(SUP9) processed shot peening which was room temperature and low temperature experiment. And we got the following characteristics from fatigue crack growth test carried out in the environment of room temperature and low temperature at $25^{\circ}C$, $-30^{\circ}C$, $-50^{\circ}C$, $-70^{\circ}C$,$-100^{\circ}C$, and $-150^{\circ}C$, in the range of stress ratio of 0.05 by means of opening mode displacement. The threshold stress intensity factor range ΔKth in the early stage of fatigue crack growth (Region I)was increased but stress intensity factor range ΔK in the stable of fatigue crack growth (Region II) was decreased in proportion to decrease temperature. It is assumed that the fatigue resistance characteristics and fracture strength at low temperature and high temperature is considerably higher than that of room temperature in the early stage and stable of fatigue crack growth region.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.188-191
• /
• 2005

Lower arm for automobile has been made in steel traditionally. Nowadays steel is being substituted fur aluminum to reduce weight of automobile. Widely applied production method of aluminum component has been casting processes or cast/forging processes. But casting or cast/forging processes have limits of application to parts which is required high strength durability like automotive component. In this research, hot forging process has been adopted to produce aluminum lower arm to ensure required mechanical properties. To reduce production cost, 2 pieces with 1 blow process was developed. Optimization and verification of hot forging process for aluminum lower arm was performed by computer aided engineering using finite volume methods.

• Journal of Welding and Joining
• /
• 제31권4호
• /
• pp.1-6
• /
• 2013

Nowadays, the weight lightening of automotive is required as conserving the environment has become a major worldwide issue. To solve this issue, various researches for the use of light materials(Alalloy, Mgalloy)and ultra high strength steel as substitutes of the current structural material have been carried out. Application of laser stitch welding to the assembly of automotive produces improvement in strength, lightening of body, higher fuel efficiency, lower production cost as well as reduction in assemble line due to its fast welding speed, superior accessible and weld quality. This process overcomes the shortcomings of the current resistance spot welding such as high electricity consumption, electrode replacement, and economical, technical limitation in design and production method of automotives.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.193-197
• /
• 2005

Influences of microstructure on high-cycle fatigue (HCF) limit of high carbon $(>0.7wt.\;\%)$ steel filaments used for tires have been investigated. A series of the fatigue tests was carried out depending on carbon content by using Hunter-type tester at a frequency of 60 Hz at a tension/compression stress of 900 to 1500 MPa. Microstructural changes of the filaments were identified in the lateral direction by using transmission electron microscopy (TEM). It was found that the mechanical properties, such as fatigue limit and tensile strength, were improved with increasing carbon content, which was mainly attributed to decreased lamellar spacing and cementite thickness. However, the fatigue ratio, which is defined as the ratio of the fatigue limit to the tensile strength, was reduced in a higher carbon range of 0.8 to $0.9\;wt.\%$, while the fatigue ratio was nearly constant in a lower carbon range of 0.7 to $0.8\;wt.\%$. Overall mechanical properties of the filaments, depending on carbon content, have been discussed in terms of the microstructural parameter change of lamellar spacing and cementite thickness. In addition, the variation of cementite morphology on the fatigue crack propagation of high carbon $(0.9wt.\;\%)$ filaments will be discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.231-234
• /
• 2009

The effects of annealing temperature and time on mechanical properties and microstructures were already investigated in cold drawn pearlitic steel wires. During annealing, the increment of the tensile strength at low temperatures found to be due to age hardening, while the decrease in the tensile strength at high temperatures was attributed to age softening, involving the spheroidization of lamellar cementite and recovery of lamellar ferrite. Since Between increase of tensile strength and the occurrence of the delamination would be closely related to the dissolution of cementite, the increase of drawing strain by lower annealing temperature caused the between higher tensile strength and the easier occurrence of the delamination in cold drawn pearlitic steel wires.

• Journal of Welding and Joining
• /
• 제33권4호
• /
• pp.50-56
• /
• 2015

In general, discontinuity of metallurgical and structural points of weld zone could decline the fatigue strength. For the lightweight trend, the AHSS application in automotive chassis is in-progress. However, there are few research reports on AHSS welds fatigue strength in especially automotive chassis parts. Therefore, in this study, we evaluated the effects of the factors affecting the AHSS welding fatigue strength. As the result, the stress concentration of weld bead is the most important factor for welding fatigue strength. For the enhancement of welding fatigue strength, we focused on reducing the stress concentration of the welding beads. So, we applied and proved the plasma welding process and GTAW (Gas Tungsten Arc Welding) dressing method. It was verified by uniaxial fatigue specimen, fatigue performance increased from 40 to 60% by applying TIG dressing method compared to the conventional GMAW (Gas Metal Arc Welding). These results could be recommended the enhancement of fatigue performance of AHSS.

• 한국레이저가공학회지
• /
• 제17권2호
• /
• pp.11-18
• /
• 2014

This research was conducted as a fundamental study to apply tailored blank welding technique into automotive production process. Specially we tried to apply the TWB technique to exhaust system. The materials used in this work were ferritic 439 stainless steel sheet with a thickness of 1.2mm and 0.8mm. Welding tests were conducted for BOP test and dissimilar thickness (0.8 to 1.2t) cases. Major process parameters were position of focus, travel speed, shielding gas and joint (gap) condition. As a result, there are nothing significant welding characteristic compare with TWB of carbon steel. Stainless steel shows the good weldability and mechanical properties (tensile, hardness and forming strength) also shows high level. Just problem is gap condition. However, also in this case, it shows not only good forming strength but also base metal fracture after tensile test. And to conclude, it is good opportunity to make lightweight design muffler using TB welding technique.