• Corrosion Science and Technology
• /
• 제23권4호
• /
• pp.302-309
• /
• 2024

The purpose of this study was to elucidate effects of a thin (tens to hundreds of nanometers) Ni-flash coating layer on hydrogen embrittlement (HE) and liquid metal embrittlement (LME) in ultra-high-strength electrogalvanized steel with a tensile strength of more than 1 GPa. Various experimental and analytical methods, including thermal desorption spectroscopy, slow strain rate testing, resistance spot welding, X-ray diffraction, and metallographic observation, were employed. Results showed that an increase in Ni target amount for flash coating resulted in a decrease in diffusible hydrogen content during electrogalvanizing, resulting in a significant decrease in HE sensitivity. Moreover, a Ni target amount of more than 1000 mg/m² drastically reduced the occurring frequency and average depth of LME. This reduction could be primarily attributed to formation of Zn-Ni intermetallic phases during the welding process that could inhibit liquefaction of intermetallic phases in the heat-affected zone. This study provides a desirable Ni target amount for Ni-flash coating on ultra-high-strength steels conducted in a continuous galvanizing line or a high-speed batch line to achieve high resistance to both HE and LME.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.918-928
• /
• 1995

This paper deals with the various mechanical properties and fatigue strength in the FRW1 (friction welded interface) of high speed steel (HSS-Co) to SM55C through the tensile test, hardness test and fatigue test. The data of FRW specimens are also compared with those of the base materials (HSS-Co and SM55C steel). Three kinds of specimens used in this study are the friction welded joints, HSS-Co and SM55C carbon steel with circumferential notch, saw notch and smooth, respectively. It is confirmed that the applied welding conditions are optimum methods in order to minimize the heat affected zone (HAZ) and hardness distribution at the HAZ. The fatigue strengths at N = 10$^{6}$ cycles of smooth, circumferential notch and saw notch specimens in the FRW joints are about 299.2 MPa, 123.8 MPa and 247.5 MPA, respectively. The fatigue strength of the friction welded joints is almost equal to that of the SM55C carbon steel in the optimum welding conditions. The fatigue cracks initiated at the welded zone are propagated along the side of SM55C steel.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.213-215
• /
• 2004

Water jet propulsion system has high efficiency on middle to high speed, and it provides better safety than conventional screw propeller because it has not projected propeller and rudder. So many leisure boat and high-speed ferries use this propulsion system. We developed water-jet propulsion unit for small planning boat, and launched that in the boat, after that we tested water-jet unit in the lake. As a result, we certify heat dissipation at the bearing housing and reverse duct's shape for neutral position are important at the design, and alignment water-jet unit and keel line are important at the launching, and ship's resistance performance and jet's propulsion performance also are needed to consideration.

• Journal of Welding and Joining
• /
• 제33권5호
• /
• pp.41-46
• /
• 2015

The snap cure NCP(non-conducive paste) adhesive material is essentially required for the high productivity flip chip bonding process. In this study, the accessibility of DEA(dielectric analysis) method for the evaluation of snap cure behavior was investigated with comparison to the isothermal DSC(differential scanning calorimetry) method. NCP adhesive was mainly formulated with epoxy resin and imidazole curing agent. Even though there were some noise in the dielectric loss factor curve measured by DEA, the cure start and completion points could be specified clearly through the data processing of cumulation and deviation method. Degree of cure by DEA method which was measured from the variation of the dielectric loss factor of adhesive material was corresponded to about 80% of the degree of cure by DSC method which was measured from the heat of curing reaction. Because the adhesive joint cured to the degree of 80% in the view point of chemical reaction reveals the sufficient mechanical strength, DEA method is expected to be used effectively in the estimation of the high speed curing behavior of snap cure type NCP adhesive material for flip chip bonding.

• Journal of Welding and Joining
• /
• 제17권3호
• /
• pp.90-95
• /
• 1999

The increase in high speed, multi-function and high I/O pin semiconductor devices highly demands high pin count, very thin, and high density packages. BGA is one of the solutions, but the package has demerits in package reliability, surface mounting problems due to the PCB warpage and solder joint crack related with TCE mismatch between the materials. On this study to verify the thermal fatigue lifetime of the solder joint FEM and experiments were performed after surface mounting BGA with different solder composition and reliability conditions. FEM showed optimum composition of Ag3.2-Sn96.5 and under the composition minimum creep deformation of the solder joint was calculated, and the thermal fatigue lifetime was improved. In view of temperature cycle condition, the conditions of $-65^{\circ}C$to $150^{\circ}C$ showed minimum lifetime and t was 1/3 of $0^{\circ}C$ to $125^{\circ}C$ condition. Test board was prepared and solder joint crack was verified. Until 1000cycle on soder joint crack was observed.

• Journal of Welding and Joining
• /
• 제26권2호
• /
• pp.92-97
• /
• 2008

In welding of thin plate, some defects such as melt through and unmelted zone occur easily at welding start, however there is a limited study on those problems. Therefore the effects of start block and arc length on melt through and unmelted zone at start were investigated in this study. When start block height was lower than base metal, there was melt through at start. And when the height was even with base metal, no unmelted zone existed. Unmelted zone was increased as start block height increased from 0mm to 0.5mm. However unmelted zone was not much changed as the height increasing from 0.5mm to 1.0mm. When gap existed between start block and base metal, melt through occurred. However, unmelted zone was increased as the contact force of start block on base metal was increased from 0kgf to 7.5kgf. And when arc length was decreased from 3.8mm to 3.0mm, unmelted zone was decreased. It was concluded that the optimum condition to prevent melt through and to minimize unmelted zone would be with start block height 0.25mm, contact force 3.0kgf, and arc length 3.4mm. This optimum condition was applied to the mass production line and resulted in satisfied outcome.

• Journal of Welding and Joining
• /
• 제12권1호
• /
• pp.59-72
• /
• 1994

This paper presents an on-line quality monitoring and control method to obtain a uniform weld quality in gas metal arc welding (GMAW) processes. The geometrical parameters of the weld pool such as the top bead width and the penetration depth plus half back width are utilized to assess the integrity of the weld quality. Since a good quality weld is characterized by a relatively high depth-to-width ratio in its dimensions, the second geometrical parameter is regulated to a desired one. The monitoring variables are the surface temperatures measured at various points on the top surface of the weldment which are strongly related to the formation of the weld pool The relationship between the measured temperatures and the weld pool size is implemented on the multilayer perceptrons which are powerful for realization of complex mapping characteristics through training by samples. For on-line quality monitoring and control, it is prerequisite to estimate the weld pool sizes in the region of transient states. For this purpose, the time history of the surface temperatures is used as the input to the neural estimator. The control purpose is to obtain a uniform weld quality. In this research, the weld pool size is directly regulated to a desired one. The proposed controller is composed of a neural pool size estimator, a neural feedforward controller and a conventional feedback controller. The pool size estimator predicts the weld pool size under growing. The feedforward controller compensates for the nonlinear characteristics of the welding process. A series of simulation studies shows that the proposed control method improves the overall system response in the presence of changes in torch travel speed during GMA welding and guarantees the uniform weld quality.

• 수산해양기술연구
• /
• 제20권1호
• /
• pp.49-59
• /
• 1984

선박용 강판(KR Grade A-1, SWS41A, SWS41B)의 수중용접 최적화에 관한 연구결과를 요약하면 다음과 같다. 1. 국산 라임티타니아계 용접봉 피복제의 흡수속도는 약 60분에서 일정하게 되고, 침수시간 8분까지의 흡수속도는 약 0.15%/min 였으므로 40cm 용접기간중의 정미 흡수량은 약 0.22%미만에 불과하였다. 2. 위의 이유와 건조, 직접, 침수용접봉에 의한 대기중, 수상, 수중용접과 모재의 인장강도 및 미시조직 비교실험결과에 의하면, 수중용접시간이 8분이내의 충분히 짧은 때에는 강도상 건조된 직접용접봉의 사용이 가능할 것이다. 3. 용접조건이 수중용접비이드에 미치는 영향을 KR Grade A-1강판에 대하여 조사한 결과, 용접각도는 60$^{\circ}$, 용접전류는 160A정도, 용접봉지름은 4mm인 경우가 적합하며, 또한 비이드외관과 X-선검사에 의하면 일미나이트, 라임티타니아, 고산화티탄계 용접봉이 가장 적합하였다. 4. 위의 용접봉 종류와 각 지름에 대해 비이드외 관검사에 의한 적정 수중용접전류의 범위는 어느 일정 범위내에 제한되며, 용접봉지름의 증가에 따라 전류는 증가하는 경향이다. 5. 수중용접부의 용착금속부에 관한 기계적특성조사에 의하면, 인장강도와 항복강도는 입열량과 이차함수적 관계가 성립되고, 이음효율이 100% 이상의 범위가 존재하며, 충격치와 스트레인은 모재의 경우보다 낮으나 그 증가현상이 고입열량 범위에서 존재하므로, SWS41A에 대한 수중용접 최적입열량범위는 약 13~15KJ/cm이다. 한편, 인장-인장 편진 피로한도가 모재의 경우보다 높고, 충격치와 연신율을 고려하여 구한 최적입열량의 범위는 약 16~19KJ/cm로서, 피로강도를 높이기 위한 입열량은 정적 인장강도때보다 고입열량으로 수중용접해야 한다. 이때 모든 실험식의 신뢰성은 95%수준이다. 6. 수중용접부에 대한 X-선검사와 미시조직검사 및 경도분포조사에 의하면 용접결함은 발견되지 않았으며, 특히, 깊이 1mm 표층부의 모재측 열영향부와 본드(bond)와의 경계부근에 경도 Hv400 max으로서 미세 마르텐사이트, 베이나이트, 퍼얼라이트와 소량의 조대한 입계페라이트 조직이며 그 외의 부위는 퍼얼라이트와 페라이트 조직으로서, 수소취성영향의 극심한 경도증가 및 조직은 발견되지 않았다. 7. 위에서 구한 입열량의 최적범위 내에서의 제어에 의하여 수중용접 할 경우, 신뢰성 있는 용접품질의 최적화가 가능할 것이다.

• 한국항해항만학회지
• /
• 제31권10호
• /
• pp.825-831
• /
• 2007

일반적으로 선박 및 해양구조물에서 사용하고 있는 고강도 알루미늄 재료들은 일반 강재에 비해서 많은 이점들을 가지고 있다. 이러한 알루미늄 재료들은 여러 분야에 걸쳐서 폭넓게 사용되고 있으며, 특히, 초고속 선박의 선체와 갑판부에 많이 이용되어지고 있고, 교량구조물에 사용되는 박스 거더, 그리고 해양구조물의 갑판부와 선측구조에도 널리 이용되고 있다. 이러한 알루미늄 구조는 전체적인 구조부재의 중량을 감소하게 하면서 선속의 증가를 가져온다. 일반적인 강구조물의 응력-변형률 관계와 비교하여 보면, 용접가공에 의하여 발생되는 열영향부의 존재로 인하여 상당히 다르게 나타난다. 왜냐하면, 강구조물에 비해 열전도율이 높아서, 열영향부(heat affected zone, HAZ)의 영향이 크게 작용하기 때문이다. 본 논문에서는 종방향 압축하중을 받는 알루미늄 보강 판넬의 최종강도 특성에 대하여, 열영향부의 범위를 변화한 유한요소해석을 통하여, 열영향부의 범위와 파굴 및 최종강도 거동의 관계에 대해서 고찰하였다.

• Journal of Welding and Joining
• /
• 제35권3호
• /
• pp.1-6
• /
• 2017

The effect of metal turnover (MTO) of electroless Ni plating bath on the brittle fracture behavior of electroless nickel electroless palladium immersion gold (ENEPIG)/Sn-3.0wt%Ag-0.5wt%Cu(SAC305) solder joint was evaluated in this study. The MTOs of the electroless Ni for the ENEPIG surface finish were 0 and 3. As the MTO increased, the interfacial IMC thickness increased. The brittle fracture behavior of the ENEPIG/SAC305 solder joint was evaluated with high speed shear (HSS) test. The HSS strength decreased with increasing the MTO of the electroless Ni bath. The brittle fracture increased with increasing the shear speed of the HSS test. The percentage of the brittle fracture for the 3 MTO sample was much higher than that for the 0 MTO sample.