• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권3호
• /
• pp.292-304
• /
• 2017

High-speed vessels are prone to the surf-riding in adverse quartering seas. The possibility of mitigating the surf-riding of the ITTC A2 fishing vessel in the design stage is investigated using the 6-DOF weakly non-linear model developed for surf-riding simulations in quartering seas. The longitudinal position of the ship's center of buoyancy (LCB) is chosen as the design parameter. The adjusting of LCB is achieved by changing frame area curves, and hull surfaces are reconstructed accordingly using the Radial Basis Function (RBF). Surf-riding motions in regular following seas for cases with different LCBs and Froude numbers are simulated using the numerical model. Results show that the surf-riding cannot be prevented by the adjusting of LCB. However, it occurs with a higher threshold speed when ship's center of buoyancy (COB) is moved towards stem compared to moving towards stern, which is mainly due to the differences on wave resistance caused by the adjusting of LCB.

• 소음진동
• /
• 제6권4호
• /
• pp.503-511
• /
• 1996

There is a tendency of using the resilient mounting system to control the structure born noise transimitted from a engine of which weight is comparatively light and of which speed is comparatively high. According to recent reports, the resilient mounting system is applied to control the vibration of a engine running up to 300 - 400 R.P.M.. Furthermore, the resilient system is also used to the ships such as marine exploring ships, fishing boats, and military vessels. It is not desirous to apply the results for the resilient mounting systems of automobile engines to the controls of the vibrations of marine engines. Marine engines are worked under the idle speed in port and are operated up to the maximum contineous revolution at sea(running up condition). And marine engines are usually worked in inevitable conditions such as a misfire and a cut-off cylinder operating condition. Concerning the above running conditions, a resilient mounting system should be designed in the case of marine engines. In this paper, we studied the effect of engine's misfire on the resilient mounting systems. And the influences of design parameters, such as dynamic characteristics and fitting angles of resilient rubber mountings, were also investigated respectively on the single and double resilient mounting systems.

• 한국해양환경ㆍ에너지학회지
• /
• 제9권2호
• /
• pp.92-97
• /
• 2006

수치계산을 통해 소형 고속선의 선형설계를 수행하였다. 선형변환 프로그램인 HCAD를 사용하고 차인형 선형을 기준선으로 하여 둥근바닥 선형을 설계하였다. WAVIS를 시용하여 두 가지 선형에 대한 선체주위의 유동장과 조파저항 계산 결과를 보였다. 차인형 선형의 저항특성이 둥근 바닥선형에 비해 다소 크게 나타났으나 소형 조선소의 건조비를 감안하여 차인형 선형의 선수부 개량과 선미 웨지의 설계를 통해 조파저항의 감소를 시도하였다. 수치계산 결과 선미 웨지의 적용에 의해 차인형 선형의 조파저항성능이 고속영역에서 개선되었음을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.90-95
• /
• 2008

Medium and high speed marine diesel engines have been widely used as prime mover in small car ferries and fishing vessels with reduction gear. These propulsion shafting system should be installed and matched the elastic coupling between engine and reduction gear to isolate the vibratory torque. In this paper, the elastic dynamic characteristics of coupling with rubber type circular segments is confirmed by the theoretical analysis using the FEM and the hydraulic exciting test at shop. And its adaptation is investigated in the torsional vibration test in factory shop.

• 한국소음진동공학회논문집
• /
• 제21권4호
• /
• pp.346-351
• /
• 2011

Medium and high speed marine diesel engines with reduction gear have been widely used as prime mover in small car ferries and fishing vessels. The elastic coupling should be installed and complemented the propulsion shafting system to isolate the vibratory torque between engine and reduction gear. In this paper, the dynamic characteristics of elastic coupling with rubber type circular segments is confirmed by theoretical analysis using the FEM and the hydraulic excitation test at shop. Further adaptation was investigated with the torsional vibration test at diesel engine factory shop.

• 수산해양기술연구
• /
• 제34권2호
• /
• pp.139-143
• /
• 1998

In the fishing process on the sea eel pots, the most dangerous and difficult labor is manually separating process of several thousand pots from main line with high speed hauling operation. In this study, the automatic separating system of the pot from main line is developed. This system is composed with the clip connected to the pot by branch line, the keeper attached to the main line by pressing and the separator separating the clip and the keeper. In the experiment, static and dynamic characteristics of the system are investigated. From the considerations on the experimental results, it is ascertained that the automatic separating system of the pot from main line proposed in this study has good operating performance.

• Fisheries and Aquatic Sciences
• /
• 제14권2호
• /
• pp.130-137
• /
• 2011

Visual stimuli of nets, which affect fishing selectivity, vary by twine diameter, color, and material under different light conditions and visual geometries. In this study, two cylindrical model codends of two mesh sizes, 28 and 43 mm, were made of high-contrast, dark brown polyethylene (PE) netting twine and low contrast, light-blue polyamid (PA) monofilament twine. Each model codend was filled with juvenile seabream and set in the water channel of a light-blue circular tank under a flow speed 0.8 m/s for 30 min. Light conditions were set to relatively bright, dim, and dark. The resulting retention rates of juvenile seabream were 15-35% lower for the low-contrast codend with PA monofilament than for the high contrast PE twine netting under bright and dim light conditions, while no difference was observed under dark conditions. The effects of mesh size and netting contrast on the retention rate were dependent on the light level, while the retention rate due to netting contrast was independent of mesh size. Therefore, low-contrast nets in the codend could help to reduce juvenile bycatch by disturbing the orderly optomotor response.

• 한국수산과학회지
• /
• 제43권6호
• /
• pp.735-739
• /
• 2010

This study investigated a method for monitoring fishes immigrating to upper streams from the sea in relation to water level with elapsed time, and measured fish behavior patterns and swimming speed in a fishing boat gateway using an acoustic camera system. This method was employed due to difficulties, linked to high turbidity, of using only underwater optical systems for monitoring fish migrating to brackish water. Results showed that fish length distribution showed high correlation between haul sampling and an automatic counting algorithm supported by the DIDSON software program. These results will help to maximize the effects of fish run management by increasing understanding of the amount of major fish species migrating in relation to durable water levels.

• 대한조선학회논문집
• /
• 제53권2호
• /
• pp.108-114
• /
• 2016

Recently, there has been a growing interest in marine leisure sports and high speed power boat for fishing. The prototype of 20 feet class power boat was developed and authors are joined in this government-led project. The research was performed to evaluate the optimal structure and design of the structural strength necessary to ensure the structural safety of the power boat. A new material ROCICORE fiber added to the mat and roving was adopted for high-power tenacity. ANSYS Workbench has been used to make the structural model, evaluate the strength and optimize the structural design. The response of the structure to quasi-static slamming loads according to the rules and regulations of ISO 12215-5, Lloyd’s Register of Shipping and Korean Register has been implemented and studied. An optimization study for the structural response is carried out by changing the plate thickness and section modulus of stiffeners. The power boat structure derived fuel efficiency is optimized by performing the best possible structural design to minimize the hull weight.

• 수산해양기술연구
• /
• 제49권3호
• /
• pp.301-310
• /
• 2013

To suggest a standard concerning with the arrangement of bridge equipment, the authors conducted the video observations with 3CCD (charge coupled device) cameras installed on the ceil of the bridge for monitoring the working activities of two bridge teams (the skipper/mate1 and the skipper/mate2) in a Korean coastal large trawler(gross tonnage: 139) for five days from July 30th. 2010 and analyzed of the data. Work elements coded by the work activities were input on the sheet of work analysis by the time unit of 1 sec according to the time occurred. A single work element among the work activities for every 5 minutes was denoted as the number of occurrence. The frequency of equipment usage was limited only in the usage of the equipment. In the case of the navigation and the towing net two ranks were integrated and analyzed. On the other hand, in the case of the casting net and the hauling net, two processes were integrated to as one and then analyzed separately as two ranks. As the results, 15 elements of work was carried out between two bridge teams for the observation; lookout, radar, GPS plotter, fish finder, net monitor, fishing deck, RPM indicator, rudder angle indicator, compass card, for maneuver; steering, ship speed control, trawl winch operation and external communications, paper works and others. It was found that the work load of the skipper per 5 minutes accordance with the navigation, the casting net, the towing net and the hauling net are 20.5 times, 11.9 times, 38.0 times and 9.5 times respectively, the mates are 65.2 times, 66.5 times, 85.7 times and 59.1 times respectively. The radar was shown the highest frequency of the equipment usage and the next was the fish finder, the GPS plotter and the external communications in the case of the navigation. In the case of the towing net the frequency of usage was high the ranking as the radar, the net monitor, the fish finder, the GPS plotter, the steering system and the external communications. In the case of the integrated process both of the casting and hauling net the trawl winch was shown the highest frequency to the skipper and the next was the GPS plotter and the radar, and the steering system was shown the highest frequency to the mate and the next was the radar, the ship speed control system, the GPS plotter, the net monitor and the fish finder.