• Computers and Concrete
• /
• v.19 no.1
• /
• pp.7-17
• /
• 2017

In Chinese Design Codes, for super high-rise buildings with complex structural distribution, which are regarded as code-exceeding buildings, elasto-plastic time history analysis is needed to validate the requirement of "no collapse under rare earthquake". In this paper, a 117-story super high-rise building is discussed. It has a height of 597 m and a height-width ratio of 9.5, which have both exceeded the limitations stipulated by the Chinese Design Codes. Mega columns adopted in this structure have cross section area of about $45m^2$ at the bottom, which is infrequent in practical projects. NosaCAD and Perform-3D, both widely used in nonlinear analyses, were chosen in this study, with which two model were established and analyzed, respectively. Elasto-plastic time history analysis was conducted to look into its seismic behavior, emphasizing on the stress state and deformation abilities under intensive seismic excitation.From the comparisons on the results under rare earthquake obtained from NosaCAD and Perform-3D, the overall responses such as roof displacement, inter story drift, base shear and damage pattern of the whole structure from each software show agreement to an extent. Besides, the deformation of the structure is below the limitation of the Chinese Codes, the time sequence and distribution of damages on core tubes are reasonable, and can dissipate certain inputted energy, which indicates that the structure can meet the requirement of "no collapse under rare earthquake".

• International Journal of High-Rise Buildings
• /
• v.5 no.1
• /
• pp.51-62
• /
• 2016

The concept of introducing viscous damping devices between outriggers and perimeter columns in tall buildings to provide supplementary damping and improve performance, reduce structural costs, and increase available usable area was developed and implemented by Smith and Willford (2007). It was recognized that the relative vertical movement that would occur between the ends of outriggers and columns, if they were not connected, could be used to generate damping. The movements, and correspondingly damping, can potentially be significantly increased by amplifying them using simple "mechanisms". The mechanisms also make it possible to increase the number of available dampers and thus further increase supplementary damping. The feasibility of mechanisms to amplify supplementary damping and enhance structural performance of tall, slender buildings is studied with particular focus on its efficacy in improving structural performance in wind loads.

• International Journal of High-Rise Buildings
• /
• v.4 no.1
• /
• pp.85-90
• /
• 2015

Advances in the technology of computational design are giving architects and engineers the opportunity to analyze buildings with complex geometries. This study explores the optimization and automation process using the parametric design method, and uses digital tools to achieve surface representation and panelization for curved shaped office buildings. In this paper, we propose parametric algorithms of dimensional and geometric constraints using the Knowledge-ware scripts embedded in Gehry Technologies' Digital Project. The knowledge-based design methods proposed in this study can be used to systemize the knowledge possessed by experts in the form of data. Such knowledge is required to promote collaboration between designers and engineers in the process of CAD/CAE/CAM. The aim of this study is to integrate the process into design, which establishes an integrated process. This integration enables two-way feedback between design and construction data by combining the methods used in designing, engineering, and construction.

• International Journal of High-Rise Buildings
• /
• v.3 no.3
• /
• pp.223-230
• /
• 2014

In this study the progressive collapse resisting capacities of tall diagrid buildings were evaluated based on arbitrary column removal scenario, and the seismic load-resisting capacities were investigated through fragility analysis and ATC 63 procedure. As analysis model structures both regular and twisted diagrid structures were designed and their load-resisting capacities were compared by nonlinear static and dynamic analyses. The analysis results showed that the progressive collapse potential of twisted buildings decreased as the twisting angle increased, but the seismic fragility or the probability of failure decreased as the twisting angle increased.

• International Journal of High-Rise Buildings
• /
• v.4 no.2
• /
• pp.103-107
• /
• 2015

China's rapidly growing cities offer a unique opportunity to create highly sustainable communities. Architects and their clients, typically real estate developers, are highly focused on strategies that are effective at reducing energy and water usage at the scale of the individual building or within a master plan of multiple related buildings. However, a closer look at energy consumption reveals that transportation uses more energy worldwide than residential and commercial buildings combined. In light of this, it is appropriate that China is making massive investments in transportation infrastructure like heavy rail rapid transit and grade separated expressways, but the end result of these investments to date has been to enable people to live further from where they work and shop rather than closer - while simultaneously not creating walkable communities. Using positive and negative examples from Asia and the rest of the world, this article will investigate the specific urban design policies such as height limits, setbacks, land use restrictions, parking ratios, and parcel size which might change to enable the creation of truly sustainable communities for China's 21st century.

• International Journal of High-Rise Buildings
• /
• v.2 no.4
• /
• pp.341-344
• /
• 2013

During a building fire, smoke can flow through elevator shafts threatening life on floors remote from the fire. Many buildings have pressurized elevators intended to prevent such smoke flow. The computer program, CONTAM, can be used to analyze the performance of pressurization smoke control systems. The design of pressurized elevators can be challenging for the following reasons: (1) often the building envelope is not capable of effectively handling the large airflow resulting from elevator pressurization, (2) open elevator doors on the ground floor tend to increase the flow from the elevator shaft at the ground floor, and (3) open exterior doors on the ground floor can cause excessive pressure differences across the elevator shaft at the ground floor. To meet these challenges, the following systems have been developed: (1) exterior vent (EV) system, (2) floor exhaust (FE) system, and ground floor lobby (GFL) system.

• International Journal of High-Rise Buildings
• /
• v.9 no.1
• /
• pp.1-15
• /
• 2020

The evolution in the use of the elevator and the iron frame to build ever-taller buildings that would eventually be called "skyscrapers" is still somewhat shrouded in the mist of history. This two-part paper is an attempt to document the significant persons and events in that evolution, showing that these had a greater continuity than that previously recorded. In this first part, I discuss how the exploitation of the elevator in the design of buildings allowed "skyscrapers" to be built taller than the five-six story limit imposed by stairways, so that their owners could include more and more rental square footage needed to offset the increasing cost of Manhattan real estate. The use of iron framing for the interior framing in these taller buildings would reduce the amount of square footage lost to construction, thereby also increasing the rental return from the building. By the start of the Great Depression of the 1870s in 1873, New York architects had erected two ten-storied skyscrapers.

• International Journal of High-Rise Buildings
• /
• v.4 no.3
• /
• pp.209-217
• /
• 2015

Outrigger systems are highly efficient since they utilize the perimeter zone to resist lateral forces, similar to tubular systems. The entire structural weight can be reduced due to the system's significant lateral strength. Therefore, it is the most commonly selected structural system for tall and supertall buildings built in recent years. In this paper, issues regarding the differential shortening effect during construction of the outrigger system and the special joints used to solve these issues will be addressed. Additionally, the characteristics of wind and seismic loads in Korea will be briefly discussed. Lastly, buildings in Korea using an outrigger as their major structural system will be introduced and the structural role of the system will be analyzed.

• International Journal of High-Rise Buildings
• /
• v.8 no.4
• /
• pp.291-302
• /
• 2019

We performed calculations combining optimization technologies and Computational Fluid Dynamics (CFD) aimed at reducing wind forces and mitigating wind environments (local strong winds) around buildings. However, the Reynolds Averaged Navier-stokes Simulation (RANS), which seems somewhat inaccurate, needs to be used to create a realistic CFD optimization tool. Therefore, in this study we explored the possibilities of optimizing calculations using RANS. We were able to demonstrate that building configurations advantageous to wind forces could be predicted even with RANS. We also demonstrated that building layouts was more effective than building configurations in mitigating local strong winds around tall buildings. Additionally, we used the Convolutional Neural Network (CNN) as an airflow prediction method alternative to CFD in order to increase the speed of optimization calculations, and validated its prediction accuracy.

• International Journal of High-Rise Buildings
• /
• v.8 no.2
• /
• pp.83-94
• /
• 2019

Diagrid structures have emerged in recent decades as an innovative solution for tube tall buildings, capable of merging structural efficiency and aesthetic quality. This paper investigates the effect of the building slenderness (grossly quantified by means of the aspect ratio, i.e., the ratio between the height and the plan dimension) on the structural behavior and on the optimal design parameters of diagrid tall buildings. For this purpose, building models with different slenderness values are designed by adopting preliminary design criteria, based on strength or stiffness demands; in addition, a design method based on a sizing optimization process that employs genetic algorithms is also proposed, with the aim to compare and/or refine the results obtained with simplified approaches.