• Journal of ILASS-Korea
• /
• v.14 no.3
• /
• pp.109-116
• /
• 2009

The purpose of this study is the experimental and numerical investigation on the DME spray characteristics in the combustion chamber according to the injection timing in a common-rail injection system. The visualization system consisted of the high speed camera with metal halide lamp was used for analyzing the spray characteristics such as spray development processes and the spray tip penetration in the free and in-cylinder spray under various ambient pressure. In order to observe the spray characteristics as a function of injection timing, the piston head shape of re-entrant type was created and the fuel injected into the chamber according to various distance between nozzle tip and piston wall in consideration of injection timing. Also, the spray and evaporation characteristics in the cylinder was calculated by using KlVA-3V code for simulating spray development process and spray tip penetration under real engine conditions. It was revealed that the high ambient pressure of 3 MPa was led to delay the spray development and evaporation of DME spray. In addition, injected sprays after BTDC 20 degrees entered the bowl region and the spray at the BTDC 30 degrees was divided into two regions. In the calculated results, the liquefied spray tip penetration and fuel evaporation were shorter and more increased as the injection timing was retarded, respectively.

• Journal of the Korean Society of Combustion
• /
• v.18 no.1
• /
• pp.27-33
• /
• 2013

Hydrogen-dimethy ether(DME) partially premixed compression ignition(PCCI) engine combustion was investigated in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME was injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME inejction timing was varied to find the optimum PCCI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. As the DME injection was retarded, the CO and HC emissions were decreased due to high combustion efficiency. NOx emissions were increased due to the high in-cylinder temperature. When DME were injected at $-30^{\circ}CA$ aTDC, reduction of HC, CO and NOx emissions was possible with high value of IMEP.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.58-65
• /
• 2003

The conventional forming process such as squeeze casting or die casting for fabricating metal matrix composites products have a disadvantage such as non homogenous distribution of reinforcement, weak bonding between matrix and reinforcement and cost increase in parts fabrication. Thixoforming process has been accepted as a new method for fabricating the net shaped metal matrix composites with lightweight and wear resistance. In this paper, the effect of volume fraction and reinforcement sizes on mechanical properties in cylinder liner part of metal matrix composites has been investigated with processes parameters such as pressure and velocity. Moreover, the methods to obtain the thixoforged composites cylinder liner with high quality has been proposed. To evaluate the composites cylinder linear fabricated at the conditions proposed in this study, mechanical properties of fabricated composites cylinder linear were compared with those of commercial composites cylinder linear.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.656-661
• /
• 2003

Modem reciprocating air compressors have tendency to a multi-stage W-type or V-type cylinder arrangement for the purpose of high outlet pressure, compactness and low vibration and noise. A valid counter weight calculation method using the complex expression is proposed for reducing the inertia forces of the compressor. Counter weight removes only 1st forward whirl component. Counter weight formulations are applied to the six various compressor structures which are (a) 1 cylinder single-throw crank shaft, (b) 2 cylinder single-throw crank shaft (c) 2 cylinder double-throw clank shaft, (d) 3 cylinder single-throw crank shaft, (e) 4 cylinder single-throw crank shaft and (f) 4 cylinder double-throw crank shaft. The improvement of performance is verified through available vibration test.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.3
• /
• pp.201-207
• /
• 2016

In this paper, an aluminum pressure vessel (cylinder) for a 200 m water depth is designed and analyzed. Because of their lack of usage in the deep sea, only a few papers about pressure vessels subjected to external pressures have previously been published. Moreover, the high level of imported external-pressure-vessel products limits the academic pursuit. Yet, research on internal pressure vessels is widely available because of their broad usage at onshore. This paper presents the process of basic designing and modelling of pressure vessels using the design rules of American Standard of Mechanical Engineering (ASME) Section VIII Division 1. To promote understanding, finite element analysis (FEA) result of an existing sample cylinder which was not designed by ASME code is compared with the design obtained in this paper. Several methodologies are used for the finite element analysis, including rectangular, cylindrical, and axisymmetric coordinate, to attain an accurate stress result. Same dimensions except the thickness of the cylinder and loading condition of 0.200 MPa was given for the current study. Finally, a rigorous design procedure is added for the bolt and boundary conditions of the cylindrical body and its ends. The obtained stress level satisfies the allowable design stress value specified in the ASME code.

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.98-103
• /
• 2015

Liquefied petroleum gas can be charged up to 85% of cylinder volume by enforcement regulations of safety control and business of liquefied petroleum gas act. The charged mass by enforcement regulations is considered by liquid expansion of internal liquefied petroleum gas at $65^{\circ}C$. But the temperature of liquid would not be suspended under $65^{\circ}C$ in a cylinder or portable vessel at certain situation. In the thermodynamics view point, the cylinder can be exposed to high pressure by liquid expansion. Consequently, it can be possible to potential risk such as physical explosion. Hence, this paper will offer a method of estimated internal pressure by liquid expansion at critical state in the closed system. Also, the structural factor which is given rise to volume increasement of cylinder is offered by experiment. This paper is expected as crucial reference for a cylinder design of liquefied petroleum gas.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2424-2429
• /
• 2015

In an oil hydraulic piston pump, the cylinder block and valve plate in high speed relative sliding motion have the characteristics which should be extremely controlled for the optimization of leakage and friction losses, and pressure-resistance design of them is very important for high pressure performance. But the studies on the stress analysis of those parts have not been performed briskly. Therefore, in this paper, the stress and displacement distributions of the cylinder block and valve plate in the oil hydraulic piston pump with a swash plate type are discussed through the static stress analysis using CATIA V5. The stress and displacement of the cylinder block are more influenced by the axial pressure than by the radial pressure, and are larger by approximately 66% and 30%, respectively. The results show that a review of the material and shape of the valve plate is required.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.4
• /
• pp.457-463
• /
• 2002

The closed cycle diesel engine is used in a closed circuit system which has no air breathing. The working fluid as intake mixture are consisted of oxygen, argon and recirculated exhaust gas in order to obtain underwater or underground power sources. In the present study, the high pressure diesel engine which can be operated by the closed cycle system with high intake pressure for increasing the net power rate is designed. It has been carried out to investigate the combustion characteristics of high pressure diesel engine according to the power rate. The maximum cylinder pressure and heat release rate were investigated. Also, major experimental data such as specific fuel consumption rate, oxygen concentrations, fuel conversion efficiency, polytropic exponent, and IMEP were compared with low pressure diesel engine experimental data.

• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.1-8
• /
• 2018

FCV is installed with a automatic valve attached in an high pressure cylinder to control the hydrogen flow. The supply of hydrogen from the cylinder into the fuel cell stack is controlled via the on/off operation of a solenoid attached to the automatic valve. The solenoid needs to provide the necessary attraction force even at any saturation temperature caused by drive of the vehicle. In this study, the simplified prediction equations for the saturation temperature are suggested. The finite element analysis was performed by steady state technique, according to the boundary condition in order to predict the saturation temperature and attraction force. Finally, the saturation temperature was validated through comparison between the analysis results and measurement results. From the results, the measured saturation temperature $5.9^{\circ}C$ lower with respect to the analysis results. And the error of attraction force ranged from 1.0 to 2.1 N at testing conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.9-16
• /
• 2006

Variable valve timing is one of the attractive ways to control homogeneous charge compression ignition (HCCI) engine. Hot internal residual gas which can be controlled by variable valve timing(VVT) device, makes fuel evaporated easily, and ignition timing advanced. Regular gasoline was used as main fuel and di-methyl ether(DME) was used as ignition promoter in this research. HCCI engine operating range is limited by high combustion peak pressure and engine noise. High combustion pressure can damage the engine during operation. To avoid engine damage, the rich limits have to define using various methods. Peak combustion pressure, rate of cylinder pressure rise was considered to determine rich limit of engine operating range. Knock probability was correlated with the rate of cylinder pressure rise as well as the peak combustion pressure.