• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.15-20
• /
• 2002

We demonstrate a widely-tunable wavelength converter based on four-wave mixing in a semiconductor-fiber ring laser with no external pump light. Applying 10 GHz short pulses at -8 dBm as a probe signal, we achieve continuous wavelength tuning over the semiconductor optical amplifier gain-bandwidth reaching 30 nm down- and 17 m up-wavelength conversion. In addition to the wide tuning capability, the converter shows high-speed conversion and low saturation power capabilities.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.657-662
• /
• 2005

In this study, the deposition of micrometer-scale metallic interconnects on LCD glass for the repair of open-circuit type defects is investigated. Although there had been a few studies Since 1980 s for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and $W(CO)_6$ was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 nm depending on laser power and scan speed while the width was controlled between $3\~50{\mu}$ using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below 1 $O\cdot{\mu}m$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.165-173
• /
• 2005

This paper presents the results for deposition of micrometer-scale metal lines on glass for the development of TFT-LCD circuit repair-system. Although there had been a few studies in the late 1980's for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and W(CO)s was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 m depending on laser power and scan speed while the width was controlled between 50um using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below $1{\Omega}{\cdotu}um$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.

• Journal of the Optical Society of Korea
• /
• v.17 no.2
• /
• pp.182-187
• /
• 2013

We present a comparative experimental analysis of the thermal spectroscopic characteristics of a phosphosilicate (P)-based ytterbium-doped fiber (YDF) against an aluminosilicate (Al)-based YDF in the temperature range of 25 to $150^{\circ}C$. We also characterize the fibers as gain media in a cladding-pumped amplifier configuration. While both fibers exhibit comparable trends in their thermal characteristics, there are noticeable distinctions in the fluorescence lifetime reduction rate and the spectral dependence of the transition cross-sections. The P- and Al-based YDFs present thermal lifetime reduction rates of $0.012%/^{\circ}C$ and $0.026%/^{\circ}C$, respectively. In particular, in the spectral region at ~940 nm, the absorption cross-section of the P-based YDF undergoes significantly less thermal change compared to that of the Al-YDF. In the cladding-pumped amplifier configuration operating at a total gain of 10 dB, the Al-based YDF generally performs betters than the P-based YDF in the temperature range of 25 to $75^{\circ}C$. However, it is highlighted that in the high temperature range of over $75^{\circ}C$, the latter shows a less gain reduction rate than the former, thereby yielding higher relative output power by 3.3% for a 1060-nm signal, for example.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.666-672
• /
• 2003

In this paper, we described the fabrication and the performance of wavelength tunable distributed bragg reflector (DBR) laser diode (LD), having different waveguide coupling mechanisms; integrated-twin-guide (ITG) DBR-LD and butt coupled (BT) DBR-LD. This deviceis fabricated by metal organic vapor phase epitaxy (MOVPE) growth and planar buried heterostructure (PBH)-type transverse current confinement structure. The result of measurement, the optical performance of BT-DBR-LD is better over 2 times than that of ITG-DBR-LD at the variation of threshold current and output power, and slop efficiency due to the higher coupling efficiency of the butt coupled structure than the integrated twin guide structure. The maximum wavelength tuning range is about 7.2nm for ITG DBR-LD and 7.4nm for BT DBR-LD. Both types of lasers have a very high yield of single mode operation with a side-mode suppression ratio of more than 35dB.

• Journal of Welding and Joining
• /
• v.25 no.3
• /
• pp.18-27
• /
• 2007

Laser welding process is widely used in the industrial field due to its numerous advantages: a small heat affected zone(HAZ), deep penetration, high welding speed, ease of automation, single-pass thick section capability, enhanced design flexibility, and small distortion after welding. The objective of this research works is to investigate the influence of the process parameters, such as the welding fur metals with CW Nd:YAG lasers. The bead-on-plate and Lap welding experiments are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the welding quality of the cross section, tensile stress behavior and the hardness of the welded part are investigated in comparison of the Nickel coated and Nickel uncoated S45C steel. As a result of experiment, nickel coated S45C Steel showed more even weld zone than Nickel uncoated counterpart upon lap welding. Also, it showed relatively small amount of internal defects and spatter, and Nickel coated S45C showed better weldability than Nickel uncoated S45C steel. The optimum welding process upon lap welding of Nickel coated S45C steel is when each laser power is 1900W; focal positions is -1mm; welding speed is $0.9{\sim}1.0m/min$. The heat input was $4.178{\sim}4.36{\times}103J/cm^2$.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.2
• /
• pp.201-207
• /
• 2012

Pulsed lasers at the 613 nm and 1064 nm wavelengths on nanoseconds have been utilized to characterize the damage on Si photodiode exposed to intense illumination. Morphological damages and structural changes at sites on the photodiode irradiated during microseconds of laser pulses were analyzed by FE-SEM images and XRD patterns, respectively. The removal of oxide coating, ripple, melting marks, ridges, and crater on photodiodes were definitely observed in order of increasing the pulse intensities generated above the damage threshold. Then, the degradation in photosensitivity of the Si photodiode irradiated by high power density pulses was measured as a function of laser irradiation time at the various wavelengths. The free charge carrier and thermal diffusion mechanisms could have been invoked to characterize the damage. The relative photosensitivity data calculated using the thermal diffusion model proposed in this paper have been compared with the experimental data irradiated above the damage threshold.

• Physical Therapy Rehabilitation Science
• /
• v.12 no.2
• /
• pp.185-191
• /
• 2023

Objective: Transcutaneous electrical nerve stimulation (TENS) is a treatment method for pain, and it can be divided into conventional TENS (C-TENS) and acupuncture-like TENS (A-TENS). More recently, high power lasers have increasingly been used to reduce pain caused by arthritis, residual neuralgia, and musculoskeletal disorders. The aim of this study was to compare the laser needle with C-TENS and A-TENS in terms of pain and blood flow in healthy people, as well as to confirm that the laser needle can replace TENS to treat pain. Design: A randomized controlled trial. Methods: The selected participants were divided using Minimize computer software into a laser group (n=13), a C-TENS group (n=13), and an A-TENS group (n=14); they underwent a pre-test for blood flow and pain in their forearm. The three groups received their respective interventions; they then underwent a second pain and blood flow test on the same spot. Results: No significant differences were observed in the A-TENS group between the pre- and post-tests, and a comparison among the three groups revealed no significant differences between the laser needle group and the C-TENS group in terms of pain. Regarding blood flow, no significant differences were found between the pre- and post-tests in the laser needle group; a comparison among the three groups only revealed a significant between the laser needle and A-TENS groups. Conclusions: This study confirmed that the laser needle can be used to treat pain when it is necessary to control blood flow.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.400-403
• /
• 2002

The fundamental experiments for measuring soft x-ray characteristics from the vacuum capillary are described. These experiments were primarily performed in order to generate line spectra such as x-ray lasers. The generator consists of a high-voltage power supply, a polarity-inversion ignitron pulse generator, a turbo-molecular pump, and a radiation tube with a capillary. A high-voltage condenser of 200 nF in the pulse generator is charged up to 20 kV by the power supply, and the electric charges in the condenser are discharged to the capillary in the tube after closing the ignitron. During the discharge, weakly ionized plasma forms on the inner and outer sides of a capillary. In the present work, the pump evacuates air from the tube with a pressure of about 1 mPa, and a demountable capillary was developed in order to measure x-ray spectra according to changes in the capillary length. In this capillary, the anode (target) and cathode elements can be changed corresponding to the objectives. The capillary diameter is 2.0 mm, and the length is adjusted from 1 to 50 mm. When a capillary with aluminum anode and cathode electrodes was employed, both the cathode voltage and the discharge current almost displayed damped oscillations. The peak values of the voltage and current increased when the charging voltage was increased, and their maximum values were -10.8 kV and 4.7 kA, respectively. The x-ray durations observed by a 1.6 ${\mu}$m aluminum filter were less than 30 ${\mu}$s, and we detected the aluminum characteristic x-ray intensity using a 6.8 ${\mu}$m aluminum filter. In the spectrum measurement, two sets of aluminum and titanium electrodes were employed, and we observed multi-line spectra. The line photon energies seldom varied according to changes in the condenser charging voltage and to changes in the electrode element. In the case where the titanium electrode was employed, the line number decreased with corresponding decreases in the capillary length. Compared with incoherent visible light, these rays from the capillary were diffracted and diffused greatly after passing through two slits.

• Korean Journal of Optics and Photonics
• /
• v.32 no.2
• /
• pp.49-54
• /
• 2021

In this paper, we design and construct the equipment to manufacture large-diameter optical fiber end caps, which are the core parts of high-power fiber lasers, and we fabricate large-diameter optical fiber end caps using the home-made equipment. This equipment consists of a CO2 laser as a fusion-splice heat source, a precision stage assembly for transferring the position of a large-diameter optical fiber and an end cap, and a vision system used for alignment when the fusion splice is interlocked with the stage assembly. The output of the laser source is interlocked with the stage assembly to control the output, and the equipment is manufactured to align the polarization axis of the large-diameter polarization-maintaining optical fiber with the vision system. Optical fiber end caps were manufactured by laser fusion splicing of a large-diameter polarization-maintaining optical fiber with a clad diameter of 400 ㎛ and an end cap of 10×5×2 ㎣ (W×D×H) using home-made equipment. Signal-light insertion loss, polarization extinction ratio, and beam quality M2 of the fabricated large-diameter optical fiber end caps were measured to be 0.6%, 16.7 dB, and 1.21, respectively.