• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.427-431
• /
• 2001

In this research, porous materials were made from mine's waste slime. As a temperature changes, a phase changes, a porosity, and a mechanical strength of porous materials were observed and measured. The process of pore-formation was observed by SEM according to the change of heat-treatment temperature and time. It fumed out that the foaming reaction of mine's waste slime was resulted from liquid phase by decomposition of the sanidine and the muscovite-3T. When heat- treated at over 120$0^{\circ}C$, it appeared high porosity. And, to activate the foaming reaction, an alkaline oxide concerned with liquid formation was added and its effects were examined.

• Journal of Technologic Dentistry
• /
• v.25 no.1
• /
• pp.21-28
• /
• 2003

The purpose of this study was to process bio-active glass ceramic composite, reinforced with sapphire fibers, by hot press. Also to study the interface of the matrix and the sapphire fiber, and the mechanical properties. Glass raw materials melted in Pt crucible at 1300$^{\circ}C$ during 3.5 hours. The melt was crushed in ball mill and then crushed material, ground and sieved to $<40{\beta}{\mu}m$. Sapphire fibers cut (30mm) and aligned. Powder and fibers hot pressed. The micrographs show good bonding between the matrix and the fiber and no porosity in the glass matrix. This means ideal fracture phenomena. Glass is fractured before the fiber. This is indication of good fracture strength. EDXS showing aluminum rich phase and crystalline phase. Bright field image of the matrix showing crystalline phase. Also diffraction pattern of TEM showing the crystalline phase and more than one phase. Strength of the samples was determined by 3 point bend testing. Strength of the 10vol% sample was approximately 69MPa, while strength of the control sample is 35MPa. Conclusions through this study as follow: 1. Micrographs show no porosity in the glass matrix and the interface. 2. The interface between the fiber and the glass matrix show no gaps. 3. Fracture of the glass indicates characteristic fiber-matrix separation. 4. Presence of crystalline phase at high processing temperature. 5. Sapphire is compatible with bioactive glass.

• Architectural research
• /
• v.20 no.1
• /
• pp.27-34
• /
• 2018

To improve the chloride ingress resistance of concrete, slag is widely used as a mineral admixture in concrete industry. And currently, most of experimental investigations about non steady state diffusion tests of chloride penetration are started after four weeks standard curing of concrete. For slag blended concrete, during submerged chloride penetration tests periods, binder reaction proceeds continuously, and chloride diffusivity decreases. However, so far the dependence of chloride ingress on curing ages are not detailed considered. To address this disadvantage, this paper shows a numerical procedure to analyze simultaneously binder hydration reactions and chloride ion penetration process. First, using a slag blended cement hydration model, degree of reactions of binders, combined water, and capillary porosity of hardening blended concrete are determined. Second, the dependences of chloride diffusivity on capillary porosity of slag blended concrete are clarified. Third, by considering time dependent chloride diffusivity and surface chloride content, chloride penetration profiles in hardening concrete are calculated. The proposed prediction model is verified through chloride immersion penetration test results of concrete with different water to binder ratios and slag contents.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.184-187
• /
• 2003

Complete prediction of second order permeability tensor for three dimensional circular braided preform is critical to understand the resin transfer molding process of composites. The permeability can be predicted by considering resin flow through the multi-axial fiber structure. In this study, permeability tensor for a 3-D circular braided preform is calculated by solving a boundary problem of a periodic unit cell. Flow field through the unit cell is obtained by using a 3-D finite volume method (FVM) and Darcy's law is utilized to obtain permeability tensor. Flow analysis for two cases that a fiber tow is regarded as impermeable solid and permeable porous medium is carried out respectively. It is found that the flow within the intra-tow region of the braided preform is negligible if inter-tow porosity is relatively high but the flow through the tow must be considered when the porosity is low. To avoid checkerboard pressure field and improve the efficiency of numerical computation, a new interpolation function for velocity variation is proposed on the basis of analytic solutions. Permeability of the braided preform is measured through a radial flow experiment and compared with the permeability predicted numerically.

• Journal of Korea Foundry Society
• /
• v.28 no.5
• /
• pp.231-236
• /
• 2008

H-NCM(Hong-Nanocast Method)has several benefits such as a lower porosity defect and high quality casting comparing to conventional die casting. Influence of casting parameters of hybrid-lower arm in rheocasting process on the slurry flow and the amount of porosity defect was investigated using experimental and simulation methods. In the present study, the Carreau model was adopted to simulate the pattern of rheological flow. Optimal casting paremeters such as injection speed and stroke variations were established. Sound products with integral microstructure and sound shape of joinning different materials of Al and steel pipe without deforming the steel pipe were obtained by the H-NCM slurry and X-ray analysis also showed integral condition throughout the entire parts.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.130-136
• /
• 2005

The effects of additional Mg content, the size and volume fraction of reinforcement phase on the mechanical properties of ceramic particle reinforced aluminium matrix composites fabricated by pressureless metal infiltration process were investigated. The hardness of $SiC_p/AC8A$ composites increased gradually with an increase in the additive Mg content, while the bending strength of $SiC_p/AC8A$ composites increased with an increase in additive Mg content up to 5%. However, this decreased when the level of additive Mg content was greater than 5% due to the formation of coarse precipitates by excessive Mg reaction and an increase in the porosity level. The hardness and strength of the composites increased with decreasing the size of SiC particle. It was found that the composites with smaller particles enhanced the interfacial bonding than those with bigger particles from fractography of the composites. The hardness of $Al_2O_{3p}/AC8A$ composites increased gradually with an increase in the volume fraction, however, the bending strength of $Al_2O_{3p}/AC8A$ composites decreased when the volume fraction of alumina particle was greater than 40% owing to the high porosity level.

• Journal of the Korean Society of Tobacco Science
• /
• v.7 no.2
• /
• pp.179-188
• /
• 1985

From the combination of cigarette papers, tipping papers and plug wrapping papers, whose physical properties and effect of cigarette smoke dilution were studied. The result obtained from this study are as follows. Envelop ventilation (Env-V'R) cigarettes used high porous cigarette papers showed less changes of unencapsulated pressure drop VPD) compared to tip ventilation (Tip-VR) cigarettes. Higher cigarette paper porosity increased, more decreased the WD of cigarette by Tip-VR. With cigarette length shortening, the UPD or VR changed a little in Tip-VR cigarette, while changed very much in Env-VR cigarettes. The ratio of nicotine/tar was higher in Env-VB cigarettes than in Tip-VR cigarettes, and CO/nicotine value of the former was lower than those of the later. The effect of Tip-VR cigarettes on the delivery reduction of tar and nicotine was more effective compared to Env-VR cigarettes and the reduction prefer Env-VR cigarettes to Tip-VR cigarettes in CO delivery. From the results investigated above it was noted that each defect appeared in the Tip-VR and the Env-VR cigarettes could be complemented by the combination of them.

• Journal of the Korean Society of Food Culture
• /
• v.33 no.1
• /
• pp.62-69
• /
• 2018

The purpose of this study was to investigate the antioxidative and physical properties of finger food type rice snacks and pumpkin rice snacks for infants aged 6 to 12 months old. The addition of rice germ did not affect density or porosity, and there was no significant difference when compared with commercial products. The addition of rice germ to the rice snack group did not reduce the longitudinal expansion quality of the rice snack. The WAI of RW and SW values were 9.83 and 8.93, respectively, which were significantly higher than those of other samples (p<0.05). The results of this study show that the addition of rice germ to rice snack resulted in reduced density and porosity of rice snacks and maintenance of a high water absorption index, which are more desirable characteristics for products. The products with rice germ showed significantly higher antioxidative activities among all samples (p<0.05).

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.186-187
• /
• 2008

Electrical resistivity in hydrate-bearing sediments is sensitive to porosity, gas hydrate saturation, gas content, pore fluid composition, and temperature, so electrical measurements such as well logs and electromagnetic surveys have been used to explore gas hydrate-bearing formation. The high pressure tomography cell is designed considering the effect of electrode configuration and electrical shielding on tomography measurements and the safety. The evolution of electrical conductivity during $CO_2$ hydrate formation and dissociation reflects the combined effects of concurrent changes that include ionization of dissolved $CO_2$, temperature-dependent ionic mobility, changes in the degree of saturation, ion exclusion, surface conduction, and porosity changes. Measurements during hydrate formation and dissociation require careful analysis to properly interpret signatures, in particular when out-of plane conductivity anomalies prevail.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.278-284
• /
• 2012

$Al_2O_3$ foam is an important engineering material because of its exceptional high-temperature stability, low thermal conductivity, good wear resistance, and stability in hostile chemical environment. In this work, $Al_2O_3$ foams were designed to control the microstructure, porosity, and cell size by varying different parameters such as the amount of amphiphile, solid loading, and stirring speed. Particle stabilized direct foaming technique was used and the $Al_2O_3$ particles were partially hydrophobized upon the adsorption of valeric acid on particles surface. The foam stability was drastically improved when these particles were irreversibly adsorbed at the air/water interface. However, there is still considerable ambiguity with regard to the effect of process parameters on the microstructure of particle-stabilized foam. In this study, the $Al_2O_3$ foam with open and closed-cell structure, cell size ranging from $20{\mu}m$ to $300{\mu}m$ having single strut wall and porosity from 75% to 93% were successfully fabricated by sintering at $1600^{\circ}C$ for 2 h in air.